Search

DC circuit breakers (DCCBs) are the key equipment to rapidly interrupt the fault current in high-voltage DC power grids and ensure the safe operation of the system. However, most DCCBs do not take current-limiting measures and rely solely on current-limiting reactors in the system to limit the rate of current rise during the interruption process. The extensive use of fully controlled power electronic devices in circuit breakers (CBs) results in high costs. To address the issues above, this paper proposes a DCCB topology with a current-limiting function based on thyristors and diodes, which can reduce the cost of CB while ensuring reliable interruption. The impact of various parameters on CB performance is analyzed using numerical calculations to optimize the parameters. Then, a simulation model of a 500 kV/16 kA DCCB is built in PSCAD/EMTDC, and the performance of the proposed CB topology is compared with the other CB topologies. By comparison, the proposed DCCB topology can reliably isolate fault currents and reduce the amplitude of fault currents and the cost of CBs. Significantly, the energy absorbed by the metal oxide varistor (MOV) during the interruption process decreases by 64.2%, reducing the cost and volume of the MOV. Finally, the feasibility of the CB is further verified in the ±500 kV 4-terminal high-voltage DC power grid simulation model. The results show that the proposed DCCB topology can limit the fault current rise rate, interrupt and isolate the fault reliably, and reduce the cost. [ABSTRACT FROM AUTHOR]

Aimed at the optimization design of the parameters of the commutation circuit of a hybrid DC-current-limiting circuit breaker (HDCCLCB), a parameter selection model considering the short-time withstand of the thyristor and the volume of the commutation circuit is proposed by simplifying the object, and the commutation circuit parameters were preliminarily obtained. In order to verify the correctness of the method of selecting the commutation circuit parameters, the circuit simulation model of the HDCCLCB was built. The experimental platform was built, and the breaking experiment was completed under the fault condition with the current rising rate of 20 A/μs. The correctness of the simulation model and parameter design method was verified by comparing the circuit model simulation results with the experimental results. In order to further optimize the parameters of the commutation circuit, a mathematical model for optimization design was established. Taking the maximum critical breakdown voltage under unit capacitance energy as the objective function, the arcing time before commutating and the current-limiting inductance and capacitance are enumerated to obtain the optimized commutation circuit parameters. By comparing this result with the result of the preliminary design, the objective function is improved by 20.7%, laying a solid foundation for further research and the development of current-limiting circuit breakers for medium-voltage DC systems. [ABSTRACT FROM AUTHOR]

This paper proposes a thyristor-based hybrid DC circuit breaker (HDCCB), which is composed of a fast mechanical circuit breaker and an LC resonant circuit with thyristor switches. The proposed HDCCB provides a zero-crossing point for fault current by injecting a resonant current in the reverse direction of the fault current. The proposed HDCCB has a low conduction loss in normal operation using a mechanical circuit breaker, and it offers the advantages of low cost, high reliability, and large capacity using thyristor switches instead of IGBT switches. It also has the design flexibility to adjust the magnitude of the injection current depending on the fault current level. A bidirectional HDCCB is also proposed by adding several components to the developed unidirectional HDCCB, which can offer compact system size and low system cost. Design considerations of the proposed structure are discussed. The validity of the proposed HDCCB is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

High voltage direct current (HVdc) power transmission systems do not encounter any natural zero crossing unlike the ac systems, and hence, the dc circuit breakers employed should be fast-acting and reliable to ensure safe operation. Circuit breakers (CBs) that have fast response time with lower energy loss dissipation are required for subsea HVdc transmission systems. This article investigates the performance of various CB topologies, including ultrafast coupled inductor hybrid CB (CIHCB) topology without and with the integration of resistive-type superconducting fault current limiter (R-SFCL) for a 100-kV, 100-MW HVdc transmission systems. It is found that the addition of R-SFCL with 1.7-ms response time decreases the peak current through the breaker and, hence, the power dissipated in the CB during short-circuit fault conditions. Thus, the rating of CB can be significantly decreased with the proposed topology. Furthermore, a comparison of power loss in CIHCB with the existing topologies, such as mechanical CB, resonant CB, and HVdc-hybrid CB, are also presented in this article. [ABSTRACT FROM AUTHOR]

High-voltage direct current (HVDC) circuit breaker development and deployment strongly depend on the testing process, which ensures that the HVDC circuit breakers will satisfy design requirements. This article presents an HVDC circuit breaker test bench circuit configuration that can provide controllable large output currents to simulate different fault conditions for the current breaking test and high output voltage for the dielectric withstand test. The current breaking test circuit is based on multiple cascaded power converters connected in parallel to provide the necessary output current capability. Each cascaded power converter is composed of multiple cells that are operated by a phase-shifted pulsewidth-modulated signal for greater controllability and higher quality of the output waveform. The dielectric withstand test circuit is a simple high-voltage source with a low power rating that can also be used to charge the test bench and the internal circuitry of the circuit breaker that is to be tested. The proposed test bench ensures that fault conditions can be replicated accurately and offers greater flexibility by being able to test mechanical, semiconductor-based, or hybrid HVDC circuit breakers with different current and voltage ratings on the same hardware without any changes. The idea and the operating principle of the proposed test bench are verified experimentally on a downscaled system that consists of three cascaded power converters connected in parallel with three cells per cascaded power converter and with a total equivalent switching frequency of 92.5 kHz. [ABSTRACT FROM AUTHOR]

It has been widely accepted to apply dc circuit breakers (DCCBs) to protect dc grids. Nevertheless, existing DCCBs have one or more following limitations: insulation recovery scheme of mechanical switch, additional precharge power supply, high conduction loss, unreliable current-breaking process, and unidirectional design. In this letter, a new DCCB with low conduction loss, simple precharging scheme, and reliable breaking ability is proposed. The proposed DCCB could break both fault and operating current actively with the same simple operation sequences. Moreover, bidirectional topology possessing all advantages mentioned previously is also presented. Topology introduction, parameters designing, and scaled-down experiment of the proposed DCCB are all presented in the letter. [ABSTRACT FROM AUTHOR]

Multi‐port hybrid DC circuit breakers (MP‐HCBs) are rapidly developing due to their obvious advantages in economy compared to traditional two‐port hybrid circuit breakers (HCBs). However, most of the existing MP‐HCB topologies do not have the current‐limiting capability, and a large number of insulated‐gate bipolar transistors (IGBTs) are still needed in their main breakers. In response to the problems, a multi‐port current‐limiting hybrid DC circuit breaker (MP‐CLHCB) based on thyristors is proposed in this paper. MP‐CLHCB uses low‐cost thyristors instead of IGBTs, and suppresses the rise of fault current through current‐limiting branch. In an attempt to prevent the MP‐CLHCB from reclosing in a permanent fault and causing damage to the DC grid again, an adaptive reclosing scheme is also proposed. In this paper, the topology, operation stages, theoretical derivation, and parameter design of the MP‐CLHCB are provided. Finally, the performance of the MP‐CLHCB is verified and compared through simulations in PSCAD/EMTDC. © 2021 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Medium voltage direct current (MVDC) power systems are in their early phase of development, but the lack of efficient and reliable DC circuit breakers is currently one of the most significant bottlenecks for widespread adoption of MVDC applications. Compared to protection devices in high voltage direct current (HVDC) systems, MVDC circuit breakers are expected to interrupt fault currents with higher rates of rise in more power-dense and more controllable structures. A hybrid approach with a piezoelectrically actuated fast mechanical switch in parallel to a solid-state circuit breaker is expected to meet the above requirements. A prototype of a 15 kV-class piezoelectrically actuated fast mechanical switch is presented in this paper. The prototype demonstrates an actuator opening time of 1 ms, a breakdown voltage of over 20 kV, and a continuous current rating of 500 A. After integrating the fast mechanical switch into a hybrid circuit breaker testbed, the fast mechanical switch was able to open within 1.5 ms and the fault was cleared within 5 ms. Therefore, piezoelectrically actuated fast mechanical switches can enable fast, reliable and controllable protection for various MVDC systems like electric ships, electric aircraft and microgrids that integrate distributed energy resources. [ABSTRACT FROM AUTHOR]

Recently the hybrid multi-port DC circuit breaker (MP-DCCB) is becoming popular in protecting HVDC grids, thanks to their reduction of power electronics devices. In this paper, an enhanced multi-port current-limiting DCCB (MP-CLCB) for multiple line protection is proposed. The integrated fault current limiter (FCL) inside the MP-CLCB can clear the fault faster with slightly increased costs. To reduce the energy dissipation requirement for the surge arresters caused by the newly added current-limiting path, an energy transfer path which provides a loop with the inductors during the current decay stage is designed. The theoretical analysis of the pre-charging, current-limiting, fault interruption and energy dissipation of the MP-CLCB is carried out. Moreover, the design principles of the energy dissipation and the key parameters of the MP-CLCB are provided. The proposed approaches are verified through simulations in PSCAD/EMTDC. The results show that the MP-CLCB can replace multiple DCCBs, accelerate the fault current interruption and reduce the energy dissipation requirement for the surge arresters. [ABSTRACT FROM AUTHOR]

Hybrid dc circuit breaker (HCB) is an effective device for interrupting dc fault currents in dc grids. Conventional two-port HCB requires too many insulated gate bipolar transistors (IGBTs) in series in its main breaker, resulting in considerable costs. Recently proposed multiport hybrid dc circuit breakers (multiport HCBs, and the number of ports is greater than or equal to 2) interrupt fault currents on multiple lines using only one shared main breaker, significantly reducing the implementation costs but losing some fault handling capabilities. To overcome these obstacles, we propose a novel high-performance economical multiport hybrid dc circuit breaker (MP-HCB) in this article. The topology and its control method are proposed. Due to the designed ring-connection structure, the proposed MP-HCB can avoid dc bus fault, and thus is more reliable. The electrical stresses of the breaker are theoretically analyzed, and the parameters are determined to make the MP-HCB capable of multiple-line faults. Compared with the typical two-port HCB and the existing multiport HCBs, the proposed MP-HCB can achieve full fault current interruption capability with lower costs. To protect a dc node connecting with three lines, the cost of the semiconductors of the proposed MP-HCB is only 1/3 of the typical two-port HCB and 1/2 of the existing multiport HCB. Finally, the performances of the proposed MP-HCB are verified via a four-terminal HVdc system in power systems computer aided design/ electromagnetic transients including DC (PSCAD/EMTDC). [ABSTRACT FROM AUTHOR]

This paper proposes a coupled inductor-based hybrid dc circuit breaker topology with zero current switching for fast fault interruption in dc systems. A series resonant circuit comprising of the secondary winding of a two-winding coupled inductor and a charged capacitor (commutation capacitor) is switched on during fault to inject a counter-current pulse, and, consequently, force a zero crossing of fault current. Proposed solution facilitates arcless breaking for a mechanical circuit breaker due to zero current turn-off. The proposed circuit breaker exhibits fast fault response ($\sim$ 30  $\mu$ s), and the response time is programmable based on the design of the coupled inductor and commutation capacitor. Furthermore, presented solution mitigates the requirement of energy-absorbing elements for demagnetizing the dc network following fault interruption, in contrast to conventional dc breakers. The paper also presents two modified circuit-breaker topologies to achieve unipolar voltage profile on the capacitor, which will enable the use of electrolytic capacitors for commutation so that the capacitor stack size is reduced in high-voltage applications. Detailed analysis and design equations are presented to explain the operation of the proposed topologies. Functionality of the proposed circuit breakers is verified through simulation, and experimental results are based on two laboratory prototypes. [ABSTRACT FROM AUTHOR]

• Hybrid DC circuit breaker with coupled inductor enables automatic current commutation. • The current commutation is faster when the rate of rise of the fault current is higher. • Flexibility in the design of the coupled inductor for current commutation. • The prototype has successful interrupted 200 A DC current within 4 ms. • Very low operating loss hybrid DC circuit breaker topology. HVDC transmission systems using voltage source converters (VSC-HVDC) have been identified as an attractive solution for bulk power delivery over long distance. However if DC grids are to be built using this technology, fast DC circuit breakers are needed. This work proposes a new hybrid DC circuit breaker utilizing a series connected coupled inductor connected, which enables automatic current commutation from the mechanical switch to the semiconductor switch during a fault. The key advantage of the proposed DC circuit breaker is that the current in the mechanical switch automatically reduces to zero when a fault happens. This paper focuses on comparison of different mechanisms to commutate the current from the mechanical switch to the semiconductor switch and create a zero current for the mechanical switch. Three types of hybrid DC circuit breaker topologies including proactive hybrid DC circuit breaker, hybrid DC circuit breaker with commutation booster, and hybrid DC circuit breaker with coupled inductor for a 500 kV HVDC system are simulated and compared using Matlab/Simulink. A prototype hybrid DC circuit breaker with coupled inductor is designed and built. The prototype is capable of interrupting 200 A direct current within 4 ms. The automatic current commutation compensates for the fault detection and location time in the selective protection scheme, which provides faster fault current interruption. [ABSTRACT FROM AUTHOR]