Search

The multiterminal dc (MTDC) grid plays an important role in large-scale power transmission and renewable energy integration owing to its excellent performance. However, there are still some problems existing in the MTDC grid, such as difficult fault current interruption and current flow control, which impedes its development. Currently, the mentioned two problems can be separately solved by hybrid dc circuit breaker (HCB) and current flow controller (CFC). However, when configured separately, they are expensive and have large footprints. Therefore, this article proposes a multiport hybrid dc circuit breaker (MHCB) with current flow control capability. The HCBs near the same dc bus are first integrated into a single MHCB and then novel CFCs are embedded into the MHCB to replace the load commutation switches. Compared with the existing MHCBs, the proposed topology shows advantages in the aspects of implementation cost, power loss, and operation speed. The operation principle is analyzed and the basis for parameter design is given in detail. The effectiveness of the proposed topology is verified by extensive simulations and experiments. Besides, the proposed MHCB is compared with the existing solutions. [ABSTRACT FROM AUTHOR]

The dc circuit breaker plays an important protection role in the dc distribution systems. Hybrid dc circuit breaker (HCB) offers low conduction losses and reasonably fast response times. In this article, a high power density, modular, and scalable power electronic interrupter (PEI) design is introduced for medium-voltage (MV) HCB platforms. Following this concept, the single low-voltage module is first investigated in terms of the high pulse current ratio and the voltage clamping circuit. After the comparison and test among different devices, a compact module with 1.7-kV discrete IGBTs are selected as main switches. While the voltage clamping circuit is carefully designed to guarantee no tail current bump and sufficient turn-off voltage margin. Next the whole system with series modules is optimized on the aspects of the turn-off strategy, power supply structure, and layout of modules. An improved staged turn-off scheme is proposed, which can not only reduce the peak current and total metal oxide varistor (MOV) energy, but also help balance the MOV energy distribution. A 12-kV and 1-kV breaking capable PEI was demonstrated based on the proposed PEI design, achieving a peak power density of 7.4 kW/cm3, much higher than the IGBT module-based solution. The breaking capability and effectiveness of the modular PEI is demonstrated in a 6-kV MVDC HCB device. [ABSTRACT FROM AUTHOR]

To improve the consumption of renewable energy and to meet complex load demands. A model of a multi-terminal flexible DC distribution network with multiple overhead branch lines is constructed. Aiming at frequent non-permanent faults of overhead lines, a fast pilot protection scheme is proposed to cover the whole fault process. Using the hybrid DC circuit breaker (HDCCB) action as the boundary mark, the fast pilot protection can be divided into two phases: post-fault and fault restart. The first phase highlights rapidity, sending a trip command to HDCCB within 1-2 ms after the fault. The second stage emphasizes reliability, and points out that the data of the whole fault process should be fully utilized, and to fully excavate the characteristics of fault current. A multi-time scale and multi-criteria fusion protection scheme is proposed, which can effectively improve the reliability of fault area identification. Finally, a corresponding model was built based on PSCAD, a large number of simulation tests and robustness analysis proved that the proposed fast pilot protection scheme is feasible. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) high-voltage direct current (HVdc) transmission is a promising method to integrate renewable energies. However, limiting the dc-link fault current and accelerating the fault-current clearance are critical issues for MMC-HVdc systems. In this article, we propose an air-core-transformer-based fault-current limiter (ACT-FCL) in cooperation with the dc circuit breaker to limit fault-current rising and decrease fault-clearing time. Compared with the conventional dc reactor, hybrid current-limiting circuit, current-commutation-based fault-current limiter (FCL), and magnetic coupling FCL, the ACT-FCL can increase the equivalent inductance during the dc fault stage to reduce the rising rate and peak of fault current. The ACT-FCL can also decrease the equivalent inductance during the fault-current-clearing stage to reduce the fault-clearing time. The simulations and laboratory experiments verify the effectiveness of the proposed ACT-FCL in the bidirectional HVdc systems. The ACT-FCL may be extended to more fields, such as dc microgrid and domestic dc transmission. [ABSTRACT FROM AUTHOR]

Multi‐port hybrid DC circuit breakers (MP‐HCBs) are rapidly developing due to their obvious advantages in economy compared to traditional two‐port hybrid circuit breakers (HCBs). However, most of the existing MP‐HCB topologies do not have the current‐limiting capability, and a large number of insulated‐gate bipolar transistors (IGBTs) are still needed in their main breakers. In response to the problems, a multi‐port current‐limiting hybrid DC circuit breaker (MP‐CLHCB) based on thyristors is proposed in this paper. MP‐CLHCB uses low‐cost thyristors instead of IGBTs, and suppresses the rise of fault current through current‐limiting branch. In an attempt to prevent the MP‐CLHCB from reclosing in a permanent fault and causing damage to the DC grid again, an adaptive reclosing scheme is also proposed. In this paper, the topology, operation stages, theoretical derivation, and parameter design of the MP‐CLHCB are provided. Finally, the performance of the MP‐CLHCB is verified and compared through simulations in PSCAD/EMTDC. © 2021 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

The diode bridge submodule (SM) is one of the basic units of a hybrid high-voltage dc circuit breaker. This article works on the low inductance design of a single SM and series SMs. For the layout design of a single SM, this article proposes a simple and clear +-shaped SM layout, the low inductance design is simplified to the optimization of two laminated busbars with a simple structure. Based on the +-shaped SM layout, this article further proposes an SM structure with holes in diodes region, the stray inductance is further reduced, and only one integrated laminated busbar is needed in a single SM. For the layout design of series SMs, this article makes full use of the layout of a single SM and the mutual inductances between the SMs, series SMs are alternately connected in reverse. The single SM layout proposed in this article is effective in reducing the stray inductance. The loop stray inductance in stage II reduced from 148.4 to 72.3 nH, a 51.3% reduction. When the two parallel IGBTs turn off a 6 kA fault current in 2 μs, the voltage spike is reduced from 786.1 to 423.4 V, a 46.1% reduction. And the stray inductance difference of the bidirectional current path is controlled to about 10 nH. The layout of series SMs proposed in this article is effective in reducing the length of the series SMs, the length is reduced by 16.7%. The experimental results show that the SMs layout proposed in this article is effective. [ABSTRACT FROM AUTHOR]

Hybrid circuit breaker (HCB) has shown good performance for interrupting dc fault current. However, a massive number of IGBTs in series is needed. These will lead to high costs and significant difficulty in balancing IGBT dynamic voltage. This paper proposes a bidirectional hybrid circuit breaker based on a cascaded half-bridge submodule structure to reduce the overall costs and implementation difficulty of HCB. The number of IGBTs is reduced by 50%, and the operating speed is fast enough. A model of a four-terminal modular multilevel converter (MMC) system with a proposed hybrid circuit breaker in different stages is developed to describe the fault blocking process more clearly. The performance of the proposed HCB is validated and compared with other HCB structure through both theoretical derivation and time-domain simulation. [ABSTRACT FROM AUTHOR]

Hybrid dc circuit breaker (HCB) is currently the most promising dc circuit breaker. However, since it requires hundreds of semiconductor switches to withstand high transient interruption voltage, the implementation cost is high. Besides, in the multiterminal dc grid, three or more HCBs may be required at a dc bus, which worsens the disadvantages of HCBs in economy and volume. In order to solve this problem, this article designs a diode-bridge multiport HCB (DB-MPB) with its control procedures. By integrating the n HCBs at the dc bus to a single n-port HCB, the number of semiconductor switches and the footprint can be reduced, while the good current interruption performance can be still maintained. Besides, for the possibility of ultrafast disconnector (UFD) failure, the proposed DB-MPB has the function of UFD failure protection. The effectiveness of the designed DB-MPB under different scenarios is verified by simulations and experimental tests. In addition, the performance comparisons in economy and functionality of the proposed DB-MPB with existed solutions are presented to highlight the advantages of the proposed solution. [ABSTRACT FROM AUTHOR]

Hybrid dc circuit breaker (HCB) is an effective device for interrupting dc fault currents in dc grids. Conventional two-port HCB requires too many insulated gate bipolar transistors (IGBTs) in series in its main breaker, resulting in considerable costs. Recently proposed multiport hybrid dc circuit breakers (multiport HCBs, and the number of ports is greater than or equal to 2) interrupt fault currents on multiple lines using only one shared main breaker, significantly reducing the implementation costs but losing some fault handling capabilities. To overcome these obstacles, we propose a novel high-performance economical multiport hybrid dc circuit breaker (MP-HCB) in this article. The topology and its control method are proposed. Due to the designed ring-connection structure, the proposed MP-HCB can avoid dc bus fault, and thus is more reliable. The electrical stresses of the breaker are theoretically analyzed, and the parameters are determined to make the MP-HCB capable of multiple-line faults. Compared with the typical two-port HCB and the existing multiport HCBs, the proposed MP-HCB can achieve full fault current interruption capability with lower costs. To protect a dc node connecting with three lines, the cost of the semiconductors of the proposed MP-HCB is only 1/3 of the typical two-port HCB and 1/2 of the existing multiport HCB. Finally, the performances of the proposed MP-HCB are verified via a four-terminal HVdc system in power systems computer aided design/ electromagnetic transients including DC (PSCAD/EMTDC). [ABSTRACT FROM AUTHOR]

DC fault isolation is one of the main challenges of the HVDC grid. DC fault current can be interrupted within several milliseconds by employing hybrid HVDC circuit breaker. However, this scheme is not cost-effective, especially in meshed HVDC grid. In this paper, a novel integrated HVDC circuit breaker by sharing components is proposed to overcome these drawbacks. Suppose that a converter in a meshed HVDC grid is connected to m DC lines. The integrated HVDC circuit breaker consists of m + 1 ultra-fast disconnectors (UFDs), m + 1 load commutation switches (LCSs), m + 1 mechanical disconnectors (DSs), and only one main breaker (MB) and surge arrester (SA). The behavior of the proposed integrated HVDC circuit breaker is similar to that of the conventional hybrid HVDC circuit breaker. These two kinds of breakers have the same operating time, which means the integrated HVDC circuit breaker is fast enough to clear DC faults. Besides, the IGBT modules in the MB and LCSs of the proposed integrated HVDC circuit breaker are connected in one direction, and the m DC lines share a single MB. Therefore, this scheme is more cost-effective compared to the conventional hybrid HVDC circuit breaker. Moreover, the adjacent lines can still be used to transmit power after DC bus faults. Simulation results on a three-terminal HVDC grid are presented to verify the effectiveness and feasibility of the proposed scheme. [ABSTRACT FROM AUTHOR]

This paper examines two new bidirectional hybrid dc circuit breaker (CB) topologies for application in meshed dc grids. The goal is to retain performance of hybrid dc CB with bidirectional current interruption while reducing semiconductor count, dc CB size, and weight. The fault current is routed to the unidirectional internal valve using multiple additional ultrafast disconnectors. Operation of both topologies is studied using a 320-kV, 16-kA simulation model, as well as demonstrated on a 900-V, 500-A lab prototype. The control systems are presented and discussed in detail. The low-voltage hardware prototypes verify performance of several new technical and operating solutions in laboratory conditions. A comparison is made with the existing dc CB topologies and performance and reliability compromises of each topology are assessed. The conclusion is that it might be possible to halve the dc CB semiconductor count while retaining same 2 ms opening speed and bidirectional operation. [ABSTRACT FROM AUTHOR]

Owing to the increased demand for DC interruption, a prototype current-limiting hybrid DC circuit breaker incorporating a fuse and a semiconductor device was developed, based on a completely novel design concept. Recently, hybrid DC breakers have been attracting attention because of their low conduction loss and high-speed current interruption capability. The superiority of this hybrid DC circuit breaker lies in the simultaneous use of the high-speed current-limiting performance of the fuse and the highly reliable current-interruption performance of the semiconductor device. Furthermore, the hybrid DC circuit breaker performs the current interruption without any mechanical contact, thus preventing any delay in operation induced by the mechanical contact. The feasibility of the proposed concept was demonstrated by the successful application of the circuit breaker in a 1 kA fault current interruption procedure. Hence, the current-limiting hybrid DC circuit breaker is suitable for low voltage and medium voltage DC system protection. As the fuses and semiconductor modules progress, the hybrid DC circuit breaker may also adapt to HVDC systems. [ABSTRACT FROM AUTHOR]

The dc fault current has a high amplitude and a fast rising speed, therefore with regard to the hybrid dc circuit breaker, it is hard to meet the requirement of a high breaking capacity while maintaining economically efficient. The SI-SFCL can prevent the speed of the fault current from rising too fast, and ensure the current remains under the interrupting capability of the dc circuit breaker, so the couse of the SI-SFCL and the dc circuit breaker is an effective solution for fault clearing in dc grids. In this paper, the current-limiting requirement of the DCCB is given, and a simplified equivalent circuit of the active SI-SFCL is proposed, based on which the matching between the electrical parameters of the active SI-SFCL and the dc circuit breaker is studied. Parameter constraint and the protection voltage range of the active SI-SFCL are given. Finally, the conclusion on the matching between the electrical parameters of the active SI-SFCL and the DCCB is verified by MATLAB/Simulink. [ABSTRACT FROM AUTHOR]

• We propose a multiport hybrid DC circuit breaker (MHCB) for fault isolation. • The MHCB is highly economical and capable of adaptive reclosing. • We describe the operating principle of the MHCB and design its parameters. • We design the reclosing criterion for the MHCB to avoid blind reclosing. • Simulations and comparisons with other schemes show the superiority and of the MHCB. In a high voltage direct current (HVDC) grid, hybrid DC circuit breakers (HCBs) are one of the effective solutions to interrupt fault currents. The conventional two-port HCB features high economic costs since the expensive insulated gate bipolar transistors (IGBTs) are needed. Each line in the multiterminal HVDC grid must be equipped with the HCB, which is extremely costly to implement. In addition, the likelihood of temporary faults is considerably raised by the fact that the HVDC grid transfers power across overhead lines (OHLs). By reclosing operations after temporary faults, the HVDC grid can resume normal operation. However, it is vital to discern between temporary faults and permanent faults before reclosing operation to prevent secondary shocks to the HVDC grid caused by blindly reclosing on permanent faults. For the problems of high cost and blind reclosing of HCBs, this article proposes a multiport HCB (MHCB) with high economy and adaptive reclosing capability. All ports of the MHCB share a single main breaker (MB) for fault isolation. The MHCB utilizes the capacitor voltage to lower the operating voltage of the metal oxide varistor (MOV), which reduces the number of IGBTs connected together at both ends of the MOV. With the above design, the expense of the MHCB is significantly decreased. Additionally, the MHCB achieves adaptive reclosing by using the difference of current amplitudes in the capacitor branch under permanent and temporary faults. [ABSTRACT FROM AUTHOR]