Search

The impact of respiratory particle composition on the equilibrium morphology and phase are not well understood. Furthermore, the effects of these different phases and morphologies on the viability of viruses embedded within these particles are equally unknown. Physiologically relevant respiratory fluid analogues were constructed, and their hygroscopic behavior were measured using an ensemble technique. A relationship between hygroscopicity and protein concentration was determined, providing additional validation to the high protein content of respiratory aerosol measured in prior works (>90%). It was found that the salt component of the respiratory particles could crystallize as a single crystal, multiple crystals, or would not crystallize at all. It was found that dried protein particles at indoor-relevant climatic conditions could exist separately in a glassy (~77% of particles) or viscoelastic state (~23% of particles). The phase state and morphology of respiratory particles may influence the viability of embedded pathogens. We recommend that pathogen research aiming to mimic the native composition of respiratory fluid should use a protein concentration of at least 90% by solute volume to improve the representativity of the pathogen’s microenvironment.

Relative humidity (RH) can affect influenza A virus (IAV) survival. However, the mechanism driving this relationship is unknown. We hypothesized that the RH-dependent survival of airborne IAV could be predicted by the efflorescence/deliquescence divergent infectivity (EDDI) hypothesis. We determined three distinct RH response zones based on the hygroscopic growth factor of carrier aerosols. These zones were classified as the super-deliquescence zone (RH > 75%), the hysteresis zone (43% < RH < 75%), and the sub-efflorescence zone (RH < 43%). We added IAV (H3N2) to protein-enriched saline and aerosolized it into sub-efflorescence or superdeliquescence zone air, yielding aerosols in the effloresced or noneffloresced state, respectively. We then adjusted the RH to an ergonomically comfortable RH (60%). Fifteen minutes post-aerosolization, the surviving fractions (arithmetic means ± standard errors) of virus were higher in effloresced aerosols (9.5 ± 0.5%) than in non-effloresced aerosols (0.40 ± 0.05%). A virus suspension was also aerosolized directly into air within the super-deliquescence, hysteresis, and sub-efflorescence zones to assess the impact of the sudden change in RH from an initial 100% saturated RH to these zonal ranges. Fifteen minutes post-aerosolization, the surviving fractions were 3 ± 0.4%, 2 ± 0.1%, and 12 ± 2%, respectively. Survival following gradual adaptation to the hysteresis zone RH range was sustained in effloresced and reduced in the non-effloresced aerosols. The EDDI model predicted the survival of IAV under seasonal conditions, offering strategies for controlling indoor air infection.

The concentration, nature, and persistence of particulate matter (PM)-bound reactive oxygen species (ROS) are of significant interest in understanding how atmospheric pollution affects health. However, the inherent difficulties in their measurement, particularly regarding the so-called "short-lived" ROS, have limited our understanding of their persistence and concentrations in the atmosphere. This paper aims to address this limitation through the analysis of PM-bound ROS measurements from the Particle Into Nitroxide Quencher (PINQ) system at an atmospheric monitoring site in the city of Heshan, Guangdong Province, China. The measured daily average and standard deviation for the measurement period was 0.050 ± 0.017 nmol·m-3. The averaged measured concentration of ROS per mass of PM and standard deviation was 0.0012 ± nmol·mg. The dataset was also correlated with standard pollutants, and a simplified model was constructed to separate the contributions of short-lived (t1/2 = 5 min) and long-lived (t1/2 ∼ infinity) ROS to total concentration using ozone, carbon monoxide, and PM mass. This showed that the short-lived ROS contribute an average of 33% of the daily PM-bound ROS burden over the measurement period, up to 52% of daily average on elevated days, and up to 71% for hourly averages. These results highlight the need for accurate measurements of short-lived ROS and provide the starting point for a general model to predict PM-bound ROS concentrations using widely available standard pollutants for future epidemiological research.

Black carbon (BC) aerosols significantly contribute to radiative budgets globally, however their actual contributions remain poorly constrained in many under-sampled ocean regions. The tropical waters north of Australia are a part of the Indo-Pacific warm pool, regarded as a heat engine of global climate, and are in proximity to large terrestrial sources of BC aerosols such as fossil fuel emissions, and biomass burning emissions from northern Australia. Despite this, measurements of marine aerosols, especially BC remain elusive, leading to large uncertainties and discrepancies in current chemistry-climate models for this region. Here, we report the first comprehensive measurements of aerosol properties collected over the tropical warm pool in Australian waters during a voyage in late 2019. The non-marine related aerosol emissions observed in the Arafura Sea region were more intense than in the Timor Sea marine region, as the Arafura Sea was subject to greater continental outflows. The median equivalent BC (eBC) concentration in the Arafura Sea (0.66 μg m

Diesel emissions contain high levels of particulate matter (PM) which can have a severe effect on the airways. Diesel PM can be effectively reduced with the substitution of diesel fuel with a biofuel such as vegetable oil. Unfortunately, very little is known about the cellular effects of these alternative diesel emissions on the airways. The aim of this study was to test whether coconut oil substitution in diesel fuel reduces the adverse effect of diesel emission exposure on human bronchial epithelial cells. Human bronchial epithelial cells were cultured at air-liquid interface for 7 days and exposed to diesel engine emissions from conventional diesel fuel or diesel fuel blended with raw coconut oil at low (10%), moderate (15%) and high (20%) proportions. Cell viability, inflammation, antioxidant production and xenobiotic metabolism were measured. Compared to conventional diesel, low fractional coconut oil substitution (10% and 15%) reduced inflammation and increased antioxidant expression, whereas higher fractional coconut oil (20%) reduced cell viability and increased inflammation. Therefore, cellular responses after exposure to alternative diesel emission are dependent on fuel composition.

The chemical composition and evolution of secondary organic aerosol (SOA) in the atmosphere represents one of the largest uncertainties in our current understanding of air quality. Despite vast research, the toxicological mechanisms relating to adverse human health effects upon exposure to particulate matter are still poorly understood. Particle-bound reactive oxygen species (ROS) may substantially contribute to observed health effects by influencing aerosol oxidative potential (OP). The role of radicals in both the formation and aging of aerosol, as well as their contribution to aerosol OP, remains highly uncertain. The profluorescent spin trap BPEAnit (9,10-bis(phenylethynyl)anthracenenitroxide), previously utilized to study combustion-generated aerosol, has been applied to provide the first estimate of particle-bound radical concentrations in SOA. We demonstrate that SOA from different atmospherically important VOC precursors have different particle-bound radical concentrations, estimated for the ozonolysis of α-pinene (0.020 ± 0.0050 nmol/μg), limonene (0.0059 ± 0.0010 nmol/μg), and β-caryophyllene (0.0025 ± 0.00080 nmol/μg), highlighting the potential importance of OH-initiated formation of particle-bound organic radicals. Additionally, the lifetime of particle-bound radical species in α-pinene SOA was estimated, and a pseudo-first-order rate constant of k = 7.3 ± 1.7 × 10–3 s–1 was derived, implying a radical lifetime on the order of minutes.

Atmospheric semi-volatile organic compounds (SVOCs) are complex in their chemical and toxicological characteristics with sources from both primary combustion emissions and secondary oxygenated aerosol formation processes. In this study, thermal desorption of PM2.5 in association with online measurement of reactive oxygen species (ROS) was carried out to study the role of SVOCs in its gas-particle partitioning. The mass concentrations of PM2.5, black carbon (BC) and p-PAHs downstream of a thermodenuder were measured online at different temperature settings (25, 50, 100, and 200 °C) to characterize PM physico-chemical properties. While the mass concentrations of PM2.5 and p-PAHs reduced to ∼34% at 200 °C compared to that in ambient temperature, BC mass concentration has decreased by 30% at the highest temperature. Furthermore, the submicron particle size distribution showed reduced particle number concentration in Aitken mode at 200 °C heating. The ROS, measured by Particle-into-Nitroxide-Quencher, also showed reduction and followed a similar trend with PM measurements, where the total ROS decreased by 12%, 31%, and 53% at 50 °C, 100 °C, and 200 °C, respectively, compared to the ambient sample. When a HEPA filter was included in the upstream of samples, 39% of gas phase ROS reduction was observed at 200 °C. This provided a good estimate of the contribution of SVOCs in ROS production in PM2.5, where decreased SVOCs concentration at 200 °C increased the percentage of particle surface area. This concludes that the surface chemistry of these organic coatings on the particles is important for assessing the health impacts of PM.

The International Agency of Research on Cancer identifies high-temperature frying, which features prominently in Chinese cooking, as producing group 2A carcinogens. This study simultaneously characterized particulate and gaseous-phase cooking emissions, monitored their reactive oxygen species (ROS) concentrations, and evaluated their impact on genetic damage and expression in exposed human bronchial epithelial cells. Five types of edible oil, three kinds of seasonings, and two dishes were assessed. Among tested edible oils, heating of soybean oil released the largest particle number concentration (2.09 × 1013 particles/(g cooking material and oil)·h) and volatile organic compounds (VOCs) emissions (12103.42 μg/(g cooking material and oil)·h). Heating of lard produced the greatest particle mass concentration (0.75 mg/(g cooking material and oil)·h). The main finding was that sunflower and rapeseed oils produced the highest ROS concentrations (80.48 and 71.75 nmol/(g cooking material and oil)·h, respectively). ROS formation most likely occurred during the autoxidation of both polyunsaturated and monounsaturated fatty acids. Among all the tested parameters, only ROS concentrations exhibited consistency with cell viability and showed significant correlations with the expression levels of CYP1A1, HIF-1a, and especially with IL-8 (the marker for oxidative stress within the cell). These findings indicate that ROS concentration is potentially a suitable metric for direct assessment of exposure levels and potential toxicity.

Recently, there has been a substantial increase in the availability and use of low-cost particulate matter sensors in a wide range of air quality applications. They carry the promise of revolutionising air quality monitoring, yet considerable reservations exist regarding their performance and capabilities, thus hindering the broader-scale utilization of these devices. In order to address these concerns and assess their feasibility and accuracy for various applications, we evaluated six low-cost PM2.5 sensors (the Sharp GP2Y1010AU0F, Shinyei PPD42NS, Plantower PMS1003, Innociple PSM305, Nova SDS011 and Nova SDL607) in laboratory and field conditions using two combustion aerosols, concrete dust and ambient particles. In assessing the performance of these sensors, we focussed on indicators such as the linearity, accuracy and precision, critically differentiating between these qualities, and employed inter-comparison (the coefficient of determination, R2). In the laboratory, all sensors responded well, with an R2 > 0.91 when the PM2.5 concentration was > 50 µg m–3, as measured by the DustTrak. In particular, the PMS1003 demonstrated good accuracy and precision in both laboratory and ambient conditions. However, some limitations were noted for the tested sensors at lower concentrations. For example, the Sharp and Shinyei sensors showed poor correlations (R2

Mosquito-repellent incense is popular for dispelling mosquitos indoors in Asia, Africa and South America. However, the released large amounts of particulate and gaseous pollutants have a negative effect on human health. We conducted real-time measurements in laboratory chamber to characterize the particulate matter, volatile organic species (VOCs), reactive oxygen species (ROS) released from the Disc and Liquid mosquito-repellent incenses using. And further to evaluate the secondary organic aerosol (SOA) formation potential indoors attributed to the main VOCs species and the health exposure risk. Results show that the disk type produces more particles but less VOCs. The particle number concentration produced by the disc and the liquid types were 130085 part/cm3 and 7963 part/cm3, respectively. The former one concentrated at the size bins below 100 nm, in comparison with the latter one mainly between 100 and 500 nm. Burning disk type produced particles carrying much higher oxidative potential (OP) 0.0430 nmol/mg. The VOCs species produced by the disc and liquid types were mainly VOC to m/z 79(benzene) and VOC to m/z 33(methanol), and the corresponding benzene concentration were 40.7 ppb and 58.6 ppb, respectively, and the methanol concentration was 26.3 ppb and 35.2 ppb, respectively. SOA formation rate related to benzene of liquid type using was larger compared to disk type, which was 0.015 mg/(m3s) and 0.012 mg/(m3s), respectively. The health risk assessment coefficient of the disc and liquid types were 6.2×10−5 and 9.1×10−5, respectively, both exceeding the limit of 1×10−6, indicating mosquito-repellent incenses is harmful to human health.

Chinese-style cooking often involves volatilization of oils which can potentially produce a large number of pollutants, which have adverse impact on environment and human health. Therefore, we have reviewed 75 published studies associated with research topic among Mainland China, Hong Kong and Taiwan, involving studies on the roles of food ingredients and oil type, cooking style impacting on generated pollutants, and human health. The highest concentration occurred including: 1) when peat, wood, and raw coal were used in stoves; 2) olive oil was adopted; 3) cooking with high temperatures; and 4) without cleaning technology. We conclude that PM concentrations for cooking emissions were between 0.14 and 24.46mg/cm3. VOC concentrations varied from 0.35 to 3.41mg/m3. Barbeque produced the greatest mass concentrations compared to Sichuan cuisine, canteen and other restaurants. The PAHs concentration emitted from the exhaust stacks, dining area and kitchen ranged from 0.0175μg/m3 to 83μg/m3. The largest amount of gaseous pollutants emitted was recorded during incomplete combustion of fuel or when a low combustion efficiency (CO2/ (CO+CO2)

Highlights • Gas phase emissions can be potentially as hazardous as the particle phase ones. • Gas phase diesel exhaust has a stronger inflammation effect on human lung cells. • Fuel oxygen content is negatively correlated to the gas phase OP. • Total VOC content is not correlated to the gas phase OP. • Idling produces emissions with the highest OP in the gas phase. Abstract The oxidative potential (OP) of the gas phase is an important and neglected aspect of environmental toxicity. Whilst prolonged exposure to particulate matter (PM) associated reactive oxygen species (ROS) have been shown to lead to negative health effects, the potential for compounds in gas phase to cause similar effects is yet to be understood. In this study we describe: the significance of the gas phase OP generated through vehicle emissions; discuss the origin and evolution of species contributing to measured OP; and report on the impact of gas phase OP on human lung cells. The model aerosol for this study was exhaust emitted from a Euro III Common-rail diesel engine fuelled with different blends of diesel and biodiesel. The gas phase of these emissions was found to be potentially as hazardous as the particle phase. Fuel oxygen content was found to negatively correlate with the gas phase OP, and positively correlate with particle phase OP. This signifies a complex interaction between reactive species present in gas and particle phase. Furthermore, this interaction has an overarching effect on the OP of both particle and gas phase, and therefore the toxicity of combustion emissions.

Biomass burning (BB) is a significant air pollution source, with global, regional and local impacts on air quality, public health and climate. Worldwide an extensive range of studies has been conducted on almost all the aspects of BB, including its specific types, on quantification of emissions and on assessing its various impacts. China is one of the countries where the significance of BB has been recognized, and a lot of research efforts devoted to investigate it, however, so far no systematic reviews were conducted to synthesize the information which has been emerging. Therefore the aim of this work was to comprehensively review most of the studies published on this topic in China, including literature concerning field measurements, laboratory studies and the impacts of BB indoors and outdoors in China. In addition, this review provides insights into the role of wildfire and anthropogenic BB on air quality and health globally. Further, we attempted to provide a basis for formulation of policies and regulations by policy makers in China.

The aerosol-driven radiative effects on marine low-level cloud represent a large uncertainty in climate simulations, in particular over the Southern Ocean, which is also an important region for sea spray aerosol production. Observations of sea spray aerosol organic enrichment and the resulting impact on water uptake over the remote Southern Hemisphere are scarce, and therefore the region is under-represented in existing parameterisations. The Surface Ocean Aerosol Production (SOAP) voyage was a 23 d voyage which sampled three phytoplankton blooms in the highly productive water of the Chatham Rise, east of New Zealand. In this study we examined the enrichment of organics to nascent sea spray aerosol and the modifications to sea spray aerosol water uptake using in situ chamber measurements of seawater samples taken during the SOAP voyage. Primary marine organics contributed up to 23 % of the sea spray mass for particles with diameter less than approximately 1 µm and up to 79 % of the particle volume for 50 nm diameter sea spray. The composition of the submicron organic fraction was consistent throughout the voyage and was largely composed of a polysaccharide-like component, characterised by very low alkane-to-hydroxyl-concentration ratios of approximately 0.1–0.2. The enrichment of organics was compared to the output from the chlorophyll-a-based sea spray aerosol parameterisation suggested by Gantt et al. (2011) and the OCEANFILMS (Organic Compounds from Ecosystems to Aerosols: Natural Films and Interfaces via Langmuir Molecular Surfactants) models. OCEANFILMS improved on the representation of the organic fraction predicted using chlorophyll a, in particular when the co-adsorption of polysaccharides was included; however, the model still under-predicted the proportion of polysaccharides by an average of 33 %. Nascent 50 nm diameter sea spray aerosol hygroscopic growth factors measured at 90 % relative humidity averaged 1.93±0.08 and did not decrease with increasing sea spray aerosol organic fractions. The observed hygroscopicity was greater than expected from the assumption of full solubility, particularly during the most productive phytoplankton bloom (B1), during which organic fractions were greater than approximately 0.4. The water uptake behaviour observed in this study is consistent with that observed for other measurements of phytoplankton blooms and can be partially attributed to the presence of sea salt hydrates, which lowers the sea spray aerosol hygroscopicity when the organic enrichment is low. The inclusion of surface tension effects only marginally improved the modelled hygroscopicity, and a significant discrepancy between the observed and modelled hygroscopicity at high organic volume fractions remained. The findings from the SOAP voyage highlight the influence of biologically sourced organics on sea spray aerosol composition; these data improve the capacity to parameterise sea spray aerosol organic enrichment and water uptake.

Soot particles, mainly coming from fuel combustion, affect climate forcing through absorbing light and also result in adverse human health outcomes. Though biodiesel or additives blending with diesel was considered environmentally friendly, the understanding on absorbing and oxidative capacity of soot emitted from them are still unclear. The water-soluble organic carbon (WSOC) content, surface chemical structure, light absorption and oxidative potential (OPDTT) of soot from biodiesel/diesel and chemicals/diesel blends were investigated utilizing total organic carbon analyzer, X-ray photoelectron spectrometer, ultraviolet–visible spectrophotometry and dithiothreitol (DTT) assay. The differences and correlations between soot properties were statistically analyzed. Chemicals/diesel blends soot owned significantly higher WSOC content, ratio of mass absorbing efficiency (MAE) in 250 and 365 nm (E2/E3), OPDTT, and higher surface carbonyl content. Coconut biodiesel/diesel blends soot contained evidently higher aromatic carbon–oxygen single bond (Ar_C–O) content, and higher MAE365. The individual comparison of biodiesel/diesel blends showed 20% coconut biodiesel blend owned the lowest WSOC, E2/E3 and OPDTT, while highest Ar_C–O and MAE365, representing strongest absorbing properties. Association analysis showed OPDTT was significantly positively correlated with WSOC. Further, the evident negative correlation between MAE365 and OPDTT was observed. Our results showed coconut biodiesel/diesel blends soot induced lower levels of oxidative potential, whereas absorption of light was higher, which have far reaching consequences on climate forcing. Therefore, it is important to evaluate the balance point between light-absorbing properties and oxidative potential, under the wide use of biodiesel.

The rapid environmental changes in Australia prompt a more thorough investigation of the influence of transportation, local emissions, and optical–chemical properties on aerosol production across the region. A month-long intensive measurement campaign was conducted during spring 2016 at Mission Beach, a remote coastal site west of the Great Barrier Reef (GBR) on the north-east coast of Australia. One aerosol pollution episode was investigated in early October. This event was governed by meteorological conditions and characterized by the increase in black carbon (BC) mass concentration (averaged value of 0.35 ± 0.20 μg m−3). Under the influence of the continental transportation, a new layer of nucleation-mode aerosols with an initial size diameter of 20 nm was observed and aerosol number concentrations reached the peak of 6733 cm−3 at a diameter of 29 nm. The averaged aerosol extinction coefficient at the height of 2 km was 150 Mm−1, with a small depolarized ratio (3.5–5%). Simultaneously, the boundary layer height presented a fall–rise trend in the presence of these enhanced aerosol concentrations and became stable in a later stage of the episode. We did not observe clear boundary layer height diurnal variations from the LiDAR observations or from the Weather Research and Forecasting (WRF) model outputs, except in an earlier stage of the aerosol episode for the former. Although the sea breeze may have been responsible for these particles, on the balance of available data, we suggest that the aerosol properties at the GBR surface during this period are more likely influenced by regional transportation of continental sources, including biomass-burning aerosols.

The dicarbonyls glyoxal (Gly) and methylglyoxal (Mgly) are key tracers for the oxidation of volatile organic compounds (VOCs) in the atmosphere, but their atmospheric chemistry in remote forest environments is not well understood. A study was carried out during Jul. 31–Nov. 5 of 2016 at the summit of Mt. Tianjing (1690 m.a.s.l.), a remote mountaintop site in southern China, to measure the levels of Gly and Mgly and explore their sources and fate. During the study period, the average mixing ratios of Gly and Mgly were 509 ± 31 pptv and 340 ± 32 pptv, respectively, with the Gly/Mgly ratios averaging 1.8 ± 0.2. Both the dicarbonyl concentrations and the Gly/Mgly ratios were significantly higher than those observed in other background sites. Production yield calculations and meteorological data analysis indicate that high levels of Gly and Mgly observed at the study site were largely a combined result of rapid in-situ formation and regional transport by prevailing winds. On average, in-situ formation from precursors is estimated to account for 67% of the observed Mgly and about 9% of the observed Gly. There were significant changes in Gly and Mgly mixing ratios among different time periods when air masses from different source regions dominated, indicating contribution of regional transport to the observed dicarbonyl mixing ratios at the study site. Biogenic emissions in eastern China and anthropogenic emissions in the Pearl River Delta region were the two main sources responsible for the dicarbonyls observed at the site during most of the sampling period, but large-scale biomass burning in central China was also important in the late autumn, as supported by a backward trajectory analysis of fire spot data and the identification of biomass burning tracers. This study provides insights into the background atmospheric chemistry and the impact of biogenic and anthropogenic sources on the dicarbonyls speciation.

Prescribed burnings are conducted in Queensland each year from August until November aiming to decrease the impact of bushfire hazards and maintain the health of vegetation. This study reports chemical characteristics of the ambient aerosol, with a focus on source apportionment of the organic aerosol (OA) fraction, during the prescribed biomass burning (BB) season in Brisbane 2013. All measurements were conducted within the International Laboratory for Air Quality and Health (ILAQH) located in Brisbane's Central Business District. Chemical composition, degree of ageing and the influence of BB emission on the air quality of central Brisbane were characterized using a compact Time of Flight Aerosol Mass Spectrometer (cToF-AMS). AMS loadings were dominated by OA (64%), followed by, sulfate (17%), ammonium (14%) and nitrates (5%). Source apportionment was applied on the AMS OA mass spectra via the multilinear engine solver (ME-2) implementation within the recently developed Source Finder (SoFi) interface. Six factors were extracted including hydrocarbon-like OA (HOA), cooking-related OA (COA), biomass burning OA (BBOA), low-volatility oxygenated OA (LV-OOA), semivolatile oxygenated OA (SV-OOA), and nitrogen-enriched OA (NOA). The aerosol fraction that was attributed to BB factor was 9%, on average over the sampling period. The high proportion of oxygenated OA (72%), typically representing aged emissions, could possess a fraction of oxygenated species transfored from BB components on their way to the sampling site.

Volatile organic compounds (VOCs) in the headspace of bubble chambers containing branches of live coral in filtered reef seawater were analysed using gas chromatography with mass spectrometry (GC-MS). When the coral released mucus it was a source of dimethyl sulfide (DMS) and isoprene; however, these VOCs were not emitted to the chamber headspace from mucus-free coral. This finding, which suggests that coral is an intermittent source of DMS and isoprene, was supported by the observation of occasional large pulses of atmospheric DMS (DMSa) over Heron Island reef on the southern Great Barrier Reef (GBR), Australia, in the austral winter. The highest DMSa pulse (320 ppt) was three orders of magnitude less than the DMS mixing ratio (460 ppb) measured in the headspace of a dynamically purged bubble chamber containing a mucus-coated branch of Acropora aspera indicating that coral reefs can be strong point sources of DMSa. Static headspace GC-MS analysis of coral fragments identified mainly DMS and seven other minor reduced sulfur compounds including dimethyl disulfide, methyl mercaptan, and carbon disulfide, while coral reef seawater was an indicated source of methylene chloride, acetone, and methyl ethyl ketone. The VOCs emitted by coral and reef seawater are capable of producing new atmospheric particles < 15 nm diameter as observed at Heron Island reef. DMS and isoprene are known to play a role in low-level cloud formation, so aerosol precursors such as these could influence regional climate through a sea surface temperature regulation mechanism hypothesized to operate over the GBR.

Biomass burning (BB) plumes were measured at the Cape Grim Baseline Air Pollution Station during the 2006 Precursors to Particles campaign, when emissions from a fire on nearby Robbins Island impacted the station. Measurements made included non-methane organic compounds (NMOCs) (PTR-MS), particle number size distribution, condensation nuclei (CN) > 3 nm, black carbon (BC) concentration, cloud condensation nuclei (CCN) number, ozone (O3), methane (CH4), carbon monoxide (CO), hydrogen (H2), carbon dioxide (CO2), nitrous oxide (N2O), halocarbons and meteorology. During the first plume strike event (BB1), a 4 h enhancement of CO (max ~ 2100 ppb), BC (~ 1400 ng m-3) and particles > 3 nm (~ 13 000 cm-3) with dominant particle mode of 120 nm were observed overnight. A wind direction change lead to a dramatic reduction in BB tracers and a drop in the dominant particle mode to 50 nm. The dominant mode increased in size to 80 nm over 5 h in calm sunny conditions, accompanied by an increase in ozone. Due to an enhancement in BC but not CO during particle growth, the presence of BB emissions during this period could not be confirmed. The ability of particles > 80 nm (CN80) to act as CCN at 0.5 % supersaturation was investigated. The ΔCCN / ΔCN80 ratio was lowest during the fresh BB plume (56 ± 8 %), higher during the particle growth period (77 ± 4 %) and higher still (104 ± 3 %) in background marine air. Particle size distributions indicate that changes to particle chemical composition, rather than particle size, are driving these changes. Hourly average CCN during both BB events were between 2000 and 5000 CCN cm-3, which were enhanced above typical background levels by a factor of 6–34, highlighting the dramatic impact BB plumes can have on CCN number in clean marine regions. During the 29 h of the second plume strike event (BB2) CO, BC and a range of NMOCs including acetonitrile and hydrogen cyanide (HCN) were clearly enhanced and some enhancements in O3 were observed (ΔO3 / ΔCO 0.001–0.074). A short-lived increase in NMOCs by a factor of 10 corresponded with a large CO enhancement, an increase of the NMOC / CO emission ratio (ER) by a factor of 2–4 and a halving of the BC / CO ratio. Rainfall on Robbins Island was observed by radar during this period which likely resulted in a lower fire combustion efficiency, and higher emission of compounds associated with smouldering. This highlights the importance of relatively minor meteorological events on BB emission ratios. Emission factors (EFs) were derived for a range of trace gases, some never before reported for Australian fires, (including hydrogen, phenol and toluene) using the carbon mass balance method. This provides a unique set of EFs for Australian coastal heathland fires. Methyl halide EFs were higher than EFs reported from other studies in Australia and the Northern Hemisphere which is likely due to high halogen content in vegetation on Robbins Island. This work demonstrates the substantial impact that BB plumes can have on the composition of marine air, and the significant changes that can occur as the plume interacts with terrestrial, aged urban and marine emission sources.

The airborne particulate matter (PM) is known to cause adverse pulmonary and cardiovascular health effects. This study investigated the diurnal characteristics of PM induced PM-bound ROS from real time measurements in typical roadside and urban background sites in Hong Kong, and identified potential influencing factors to its variation in atmosphere. A nitroxide probe (BPEAnit) was employed in the real-time measurement of separate PM and gas phase induced reactive oxygen species (ROS) with a Particle-into-Liquid-Sampler. Measurements were carried in 2 h intervals over a 24 h period, and repeated for 6 days at each site. The total ROS (particle + gas phase) measurements resulted in multiple peaks at 08:00, 16:00 and 20:00 h time periods at background site, compared to non-intermittent decrease/increase trends at roadside. The total ROS generation was noted significantly higher by 50–100% (n = 6 p < .05) at roadside compared to the background site. While the contribution of PM2.5- and gas phase-induced ROS to the total ROS was on average 48 ± 8% and 52 ± 8% across 24 h at background site, the ratio of gas phase-induced ROS increased to 79 ± 4% and that of particle phase decreased to 21 ± 4% at roadside site. The total ROS well correlated with black carbon (BC) and particle-bound PAHs (p-PAHs), which are 4–8 fold and 10–20 fold higher at roadside than background. The ratio of p-PAHs/BC was high at roadside during peak hours compared to late nights suggesting fresh PM may have induced more total ROS generation compared to aged aerosols using this specific ROS probe.

Nitrogen (N) content in algae hydrothermal liquefaction (HTL) biocrude is high (5–8 wt%) and generally presumed to result in high NOx emissions during combustion. However, to our knowledge a very limited previous work on diesel engine performance and emissions of N-containing fuels. In order to investigate this issue, pyridine, an N-heterocyclic compound commonly found in algae biocrude, was blended with diesel fuel. This study investigated the influence of N in fuels, using a surrogate fuel to simulate algal biocrude, to determine the combustion behavior and emissions profile of an industrial multi-cylinder diesel engine. The presence of N in the fuel affected its physical properties. Density was slightly higher than neat diesel, while the viscosity, the flash point and the higher heating value (HHV) of the N-containing fuels reduced with increasing N content. The flash point of N-containing fuels were reduced, which affects the storage and transportation of the fuel. The engine load between 25 and 75% was observed to have an effect on engine performance parameters. Compared to diesel, N-containing fuels emitted both lower carbon monoxide (CO) and unburned hydrocarbons (HC). Increasing nitrogen oxides (NOx) emissions were observed with increasing N content in the fuels. At 50% and 75% loads, NOx emissions from N0.1 (0.1 wt% N), N0.5 (0.5 wt% N) and N2 (2 wt% N) were lower than for EUROIII. Particulate matter (PM) was lower for N-containing fuels compared to diesel fuel except for N0.1.

Internally and externally mixed aerosols present significant challenges in assessing the hygroscopicity of each aerosol component. This study presents a new sampling technique which uses differences in volatility to separate mixtures and directly examine their respective composition and hygroscopic contribution. A shared thermodenuder and unheated bypass line are continuously cycled between an aerosol mass spectrometer and a volatility and hygroscopicity tandem differential mobility analyser, allowing real-time comparative analysis of heated and unheated aerosol properties. Measurements have been taken of both chamber-generated secondary organic aerosol and coastal marine aerosol at Cape Grim, Australia, to investigate system performance under diverse conditions. Despite rapidly changing aerosol properties and the need to restrict analysis to a narrow size range, the former experiment separated the hygroscopic influences of ammonium sulfate and two distinct organic components with similar oxygen to carbon ratios but different volatilities. Analysis of the marine aerosol revealed an external mixture of non-sea-salt sulfates and sea spray aerosol, which likely shared similar volatile fractions composed of sulfuric acid and a non-hygroscopic organic component.

Air pollution exposure is associated with a range of adverse health effects, including cardiovascular and respiratory diseases. Particle-bound ROS has been recognised as one of the prevailing parameters to indicate the toxic potential of airborne particulate matter (PM). The temporal variability of particle-bound ROS is a very important metric crucial for the improvement of public health and risk assessment policies. To our knowledge this is the first study aiming to investigate diurnal ROS profiles in both the particle and gas phase and associate them with diurnal variations of important pollutants. For that purpose, we have successfully applied a new instrument to continuously monitor diurnal ROS profiles at two locations in Hong Kong: a busy roadside and an urban background. Data was collected over both the working week and during weekends. We have observed a high correlation between particle-bound ROS and lower concentrations of black carbon (BC) at the roadside during the working week. These associations were less significant over the weekend and at all times with ozone. Our results suggest that most of the particle-bound ROS from both the particle and the gas phase arises from fresh emission sources directly from the traffic. A very interesting observation came out as a result of this study where measured ROS concentration was decreasing with the rise of ozone in conjunction with particle number, suggesting potential role of ROS in particle growth and aging.

This study is seeking to investigate the effect of non-thermal plasma technology in the abatement of particulate matter (PM) from the actual diesel exhaust. Ozone (O3) strongly promotes PM oxidation, the main product of which is carbon dioxide (CO2). PM oxidation into the less harmful product (CO2) is the main objective whiles the correlation between PM, O3 and CO2 is considered. A dielectric barrier discharge reactor has been designed with pulsed power technology to produce plasma inside the diesel exhaust. To characterise the system under varied conditions, a range of applied voltages from 11 kVPP to 21 kVPP at repetition rates of 2.5, 5, 7.5 and 10 kHz, have been experimentally investigated. The results show that by increasing the applied voltage and repetition rate, higher discharge power and CO2 dissociation can be obtained. The PM removal efficiency of more than 50% has been achieved during the experiments and high concentrations of ozone on the order of a few hundreds of ppm have been observed at high discharge powers. Furthermore, O3, CO2 and PM concentrations at different plasma states have been analysed for time dependence. Based on this analysis, an inverse relationship between ozone concentration and PM removal has been found and the role of ozone in PM removal in plasma treatment of diesel exhaust has been highlighted.

In the prospect of limited energy resources and climate change, effects of alternative biofuels on primary emissions are being extensively studied. Our two recent studies have shown that biodiesel fuel composition has a significant impact on primary particulate matter emissions. It was also shown that particulate matter caused by biodiesels was substantially different from the emissions due to petroleum diesel. Emissions appeared to have higher oxidative potential with the increase in oxygen content and decrease of carbon chain length and unsaturation levels of fuel molecules. Overall, both studies concluded that chemical composition of biodiesel is more important than its physical properties in controlling exhaust particle emissions. This suggests that the atmospheric aging processes, including secondary organic aerosol formation, of emissions from different fuels will be different as well. In this study, measurements were conducted on a modern common-rail diesel engine. To get more information on realistic properties of tested biodiesel particulate matter once they are released into the atmosphere, particulate matter was exposed to atmospheric oxidants, ozone and ultra-violet light; and the change in their properties was monitored for different biodiesel blends. Upon the exposure to oxidative agents, the chemical composition of the exhaust changes. It triggers the cascade of photochemical reactions resulting in the partitioning of semi-volatile compounds between the gas and particulate phase. In most of the cases, aging lead to the increase in volatility and oxidative potential, and the increment of change was mainly dependent on the chemical composition of fuels as the leading cause for the amount and the type of semi-volatile compounds present in the exhaust.

The effect of non-thermal plasma technology for particulate matter removal and nitrogen oxide emission reduction from diesel exhaust has been investigated. A sample of exhaust was cooled to the ambient temperature and passed through a dielectric barrier discharge reactor. This reactor was employed for producing plasma inside the diesel exhaust. A range of discharge powers by varying the applied voltage from 7.5 to 13.5 kV (peak–peak) at a frequency of 50 Hz has been evaluated during the experiments. Regarding the NOx emission concentration, the maximum removal efficiency has been achieved at energy density of 27 J/L. Soot, soluble organic fraction and sulphate components of diesel particulate matter have been analysed separately, and the consequence of plasma exposure on particle size distribution on both the nucleation and accumulation modes has been studied. Plasma was found to be very effective for soot removal, and it could approach complete removal efficiency for accumulation mode particles. However, when applied voltage approached 12 kV, the total number of nucleation mode particles increased by a factor of 50 times higher than the total particle numbers at the reactor inlet. This increase in nucleation mode particles increased even more when applied voltage was set at 13.5 kV.

Several cell-free assays are currently used to quantify and detect the Reactive Oxygen Species (ROS). All of them have certain limitations, do not provide direct comparison of results and, to date, none of these assays have been acknowledged as the most suitable acellular assay and none has yet been adopted for investigation of potential PM toxicity. These assays include DTT, ascorbic acid, DCFHDA and PFN assays which have been used in measurements of the particles generated from various combustion sources such as diesel engine, wood smoke (or biomass burning) and cigarette smoke, as well as for outdoor measurements. All the probes use different units for expressing redox properties of PM. Also, their reactivity is being triggered by different types of ROS. This limits the direct comparison of the results that are reporting the toxicity of the same aerosol type measured with various probes. This study is evaluating and comparing the various assays in order to develop deeper understanding of their capabilities, selectivity as well as improve understanding of the underlying chemical mechanisms. Keywords: DTT, DCFH-DA, PFN, BPEA-nit, Ascorbic acid, oxidative potential

In aerosol research, a common approach for the collection of particulate matter (PM) is the use of filters in order to obtain sufficient material to undertake analysis. For subsequent chemical and toxicological analyses, in most of cases the PM needs to be extracted from the filters. Sonication is commonly used to most efficiently extract the PM from the filters. Extraction protocols generally involve 10 - 60 min of sonication. The energy of ultrasonic waves causes the formation and collapse of cavitation bubbles in the solution. Inside the collapsing cavities the localised temperatures and pressures can reach extraordinary values. Although fleeting, such conditions can lead to pyrolysis of the molecules present inside the cavitation bubbles (gases dissolved in the liquid and solvent vapours), which results in the production of free radicals and the generation of new compounds formed by reactions with these free radicals. For example, simple sonication of pure water will result in the formation of detectable levels of hydroxyl radicals. As hydroxyl radicals are recognised as playing key roles as oxidants in the atmosphere the extraction of PM from filters using sonication is therefore problematic. Sonication can result in significant chemical and physical changes to PM through thermal degradation and other reactions. In this article, an overview of sonication technique as used in aerosol research is provided, the capacity for radical generation under these conditions is described and an analysis is given of the impact of sonication-derived free radicals on three molecular probes commonly used by researchers in this field to detect Reactive Oxygen Species in PM.

Compression ignition (CI) engine design is subject to many constraints, which present a multicriteria optimization problem that the engine researcher must solve. In particular, the modern CI engine must not only be efficient but must also deliver low gaseous, particulate, and life cycle greenhouse gas emissions so that its impact on urban air quality, human health, and global warming is minimized. Consequently, this study undertakes a multicriteria analysis, which seeks to identify alternative fuels, injection technologies, and combustion strategies that could potentially satisfy these CI engine design constraints. Three data sets are analyzed with the Preference Ranking Organization Method for Enrichment Evaluations and Geometrical Analysis for Interactive Aid (PROMETHEE-GAIA) algorithm to explore the impact of (1) an ethanol fumigation system, (2) alternative fuels (20% biodiesel and synthetic diesel) and alternative injection technologies (mechanical direct injection and common rail injection), and (3) various biodiesel fuels made from 3 feedstocks (i.e., soy, tallow, and canola) tested at several blend percentages (20-100%) on the resulting emissions and efficiency profile of the various test engines. The results show that moderate ethanol substitutions (∼20% by energy) at moderate load, high percentage soy blends (60-100%), and alternative fuels (biodiesel and synthetic diesel) provide an efficiency and emissions profile that yields the most "preferred" solutions to this multicriteria engine design problem. Further research is, however, required to reduce reactive oxygen species (ROS) emissions with alternative fuels and to deliver technologies that do not significantly reduce the median diameter of particle emissions. © 2013 American Chemical Society.

Highlights - The first review of shipping emissions in China - An overview of the broad field of ship emissions and their atmospheric impacts in China - Future work in shipping related air pollution field has been outlooked. Abstract China has > 400 ports, is home to 7 of 10 biggest ports in the world and its waterway infrastructure construction has been accelerating over the past years. But the increasing number of ports and ships means increasing emissions, and in turn, increasing impact on local and regional air pollution. This paper presents an overview of the broad field of ship emissions in China and their atmospheric impacts, including topics of ship engine emissions and control, ship emission factors and their measurements, developing of ship emission inventories, shipping and port emissions of the main shipping areas in China, and quantitative contribution of shipping emissions to the local and regional air pollution. There have been an increasing number of studies published on all the above aspects, yet, this review identified some critical research gaps, filling of which is necessary for better control of ship emissions, and for lowering their impacts. In particular, there are very few studies on inland ports and river ships, and there are few national scale ship emission inventories available for China. While advanced method to estimate ship emission based on ship AIS activities makes it now possible to develop high spatial- and temporal-resolution emission inventories, the ship emission factors used in Chinese studies have been based mainly on foreign measurements. Further, the contribution of ship emissions to air pollution in coastal cities, the dispersion of pollution plumes emitted by ships, or the chemical evolution process along the transmission path, have so far not been systematically studied in China.

Particles emitted by vehicles are known to cause detrimental health effects, with their size and oxidative potential among the main factors responsible. Therefore, understanding the relationship between traffic composition and both the physical characteristics and oxidative potential of particles is critical. To contribute to the limited knowledge base in this area, we investigated this relationship in a 4.5 km road tunnel in Brisbane, Australia. On-road concentrations of ultrafine particles (

A 4-cylinder Ford 2701C test engine was used in this study to explore the impact of ethanol fumigation on gaseous and particle emission concentrations. The fumigation technique delivered vaporised ethanol into the intake manifold of the engine, using an injector, a pump and pressure regulator, a heat exchanger for vaporising ethanol and a separate fuel tank and lines. Gaseous (Nitric oxide (NO), Carbon monoxide (CO) and hydrocarbons (HC)) and particulate emissions (particle mass (PM2.5) and particle number) testing was conducted at intermediate speed (1700 rpm) using 4 load settings with ethanol substitution percentages ranging from 10% to 40% (by energy). With ethanol fumigation, NO and PM2.5 emissions were reduced, whereas CO and HC emissions increased considerably and particle number emissions increased at most test settings. It was found that ethanol fumigation reduced the excess air factor for the engine and this led to increased emissions of CO and HC, but decreased emissions of NO. PM2.5 emissions were reduced with ethanol fumigation, as ethanol has a very low "sooting" tendency. This is due to the higher hydrogen-to-carbon ratio of this fuel, and also because ethanol does not contain aromatics, both of which are known soot precursors. The use of a diesel oxidation catalyst (as an after-treatment device) is recommended to achieve a reduction in the four pollutants that are currently regulated for compression ignition engines. The increase in particle number emissions with ethanol fumigation was due to the formation of volatile (organic) particles; consequently, using a diesel oxidation catalyst will also assist in reducing particle number emissions. © 2011 Elsevier Ltd. All rights reserved.

Particulate matter (PM) emissions involve a complex mixture of solid and liquid particles suspended in a gas, where it is noted that PM emissions from diesel engines are a major contributor to the ambient air pollution problem. While epidemiological studies have shown a link between increased ambient PM emissions and respiratory morbidity and mortality, studies of this design are not able to identify the PM constituents responsible for driving adverse respiratory health effects. This review explores in detail the physico-chemical properties of diesel PM (DPM) and identifies the constituents of this pollution source that are responsible for the development of respiratory disease. In particular, this review shows that the DPM surface area and adsorbed organic compounds play a significant role in manifesting chemical and cellular processes that if sustained can lead to the development of adverse respiratory health effects. The mechanisms of injury involved included inflammation, innate and acquired immunity, and oxidative stress. Understanding the mechanisms of lung injury from DPM will enhance efforts to protect at-risk individuals from the harmful respiratory effects of air pollutants.

Oxidative stress caused by generation of free radicals and related reactive oxygen species (ROS) at the sites of deposition has been proposed as a mechanism for many of the adverse health outcomes associated with exposure to particulate matter (PM). Recently, a new profluorescent nitroxide molecular probe (BPEAnit) developed at QUT was applied in an entirely novel, rapid and non-cell based assay for assessing the oxidative potential of particles (i.e. potential of particles to induce oxidative stress). The technique was applied on particles produced by several combustion sources, namely cigarette smoke, diesel exhaust and wood smoke. One of the main findings from the initial studies undertaken at QUT was that the oxidative potential per PM mass significantly varies for different combustion sources as well as the type of fuel used and combustion conditions. However, possibly the most important finding from our studies was that there was a strong correlation between the organic fraction of particles and the oxidative potential measured by the PFN assay, which clearly highlights the importance of organic species in particle-induced toxicity.

Volatile properties of particle emissions from four compressed natural gas (CNG) and four diesel buses were investigated under steady-state and transient driving modes on a chassis dynamometer. The exhaust was diluted utilizing a full-flow continuous volume sampling system and passed through a thermodenuder at controlled temperature. Particle number concentration and size distribution were measured with a condensation particle counter and a scanning mobility particle sizer, respectively. We show that while almost all the particles emitted by the CNG buses were in the nanoparticle size range, at least 85% and 98% were removed at 100 and 250 °C, respectively. Closer analysis of the volatility of particles emitted during transient cycles showed that volatilization began at around 40 °C, with the majority occurring by 80 °C. Particles produced during hard acceleration from rest exhibited lower volatility than those produced during other times of the cycle. On the basis of our results and the observation of ash deposits on the walls of the tailpipes, we suggest that these nonvolatile particles were composed mostly of ash from lubricating oil. Heating the diesel bus emissions to 100 °C removed ultrafine particle numbers by 69-82% when a nucleation mode was present and just 18% when it was not.

Alternative fuels and injection technologies are a necessary component of particulate emission reduction strategies for compression ignition engines. Consequently, this study undertakes a physicochemical characterization of diesel particulate matter (DPM) for engines equipped with alternative injection technologies (direct injection and common rail) and alternative fuels (ultra low sulfur diesel, a 20% biodiesel blend, and a synthetic diesel). Particle physical properties were addressed by measuring particle number size distributions, and particle chemical properties were addressed by measuring polycyclic aromatic hydrocarbons (PAHs) and reactive oxygen species (ROS). Particle volatility was determined by passing the polydisperse size distribution through a thermodenuder set to 300 °C. The results from this study, conducted over a four point test cycle, showed that both fuel type and injection technology have an impact on particle emissions, but injection technology was the more important factor. Significant particle number emission (54%-84%) reductions were achieved at half load operation (1% increase-43% decrease at full load) with the common rail injection system; however, the particles had a significantly higher PAH fraction (by a factor of 2 to 4) and ROS concentrations (by a factor of 6 to 16) both expressed on a test-cycle averaged basis. The results of this study have significant implications for the health effects of DPM emissions from both direct injection and common rail engines utilizing various alternative fuels. © 2011 American Chemical Society.

Reactive oxygen species (ROS) and related free radicals are considered to be key factors underpinning the various adverse health effects associated with exposure to ambient particulate matter. Therefore, measurement of ROS is a crucial factor for assessing the potential toxicity of particles. In this work, a novel profluorescent nitroxide, BPEAnit, was investigated as a probe for detecting particle-derived ROS. BPEAnit has a very low fluorescence emission due to inherent quenching by the nitroxide group, but upon radical trapping or redox activity, a strong fluorescence is observed. BPEAnit was tested for detection of ROS present in mainstream and sidestream cigarette smoke. In the case of mainstream cigarette smoke, there was a linear increase in fluorescence intensity with an increasing number of cigarette puffs, equivalent to an average of 101 nmol ROS per cigarette based on the number of moles of the probe reacted. Sidestream cigarette smoke sampled from an environmental chamber exposed BPEAnit to much lower concentrations of particles, but still resulted in a clearly detectible increase in fluorescence intensity with sampling time. It was calculated that the amount of ROS was equivalent to 50 ± 2 nmol per mg of particulate matter; however, this value decreased with ageing of the particles in the chamber. Overall, BPEAnit was shown to provide a sensitive response related to the oxidative capacity of the particulate matter. These findings present a good basis for employing the new BPEAnit probe for the investigation of particle-related ROS generated from cigarette smoke as well as from other combustion sources.

The influence of biogenic particle formation on climate is a well recognised phenomenon. To understand the mechanisms underlying the biogenic particle formation, determining the chemical composition of the new particles and therefore the species that drive the particle production is of utmost importance. Due to the very small amount of mass involved, indirect approaches are frequently used to infer the composition. We present here the results of such an indirect approach by simultaneously measuring volatile and hygroscopic properties of newly formed particles in a forest environment. It is shown that the particles are composed of both sulphates and organics, with the amount of sulphate component strongly depending on the available gas-phase sulphuric acid, and the organic components having the same volatility and hygroscopicity as photo-oxidation products of a monoterpene such as α-pinene. Our findings agree with a two-step process through nucleation and cluster formation followed by simultaneous growth by condensation of sulphates and organics that take the particles to climatically relevant sizes.

Particle deposition indoors is one of the most important factors that determine the effect of particle exposure on human health. While many studies have investigated the particle deposition of non-biological aerosols, few have investigated biological aerosols and even fewer have studied fungal spore deposition indoors. The purpose of this study was, for the first time, to investigate the deposition rates of fungal particles in a chamber of 20.4 m3 simulating indoor environments by: 1) releasing fungal particles into the chamber, in sufficient concentrations so the particle deposition rates can be statistically analysed; 2) comparing the obtained deposition rates with non-bioaerosol particles of similar sizes, investigated under the same conditions; and 3) investigating the effects of ventilation on the particle deposition rates. The study was conducted for a wide size range of particle sizes (0.54 – 6.24 µm), at three different air exchange rates (0.009, 1.75 and 2.5 h-1). An Ultraviolet Aerodynamic Particle Sizer Spectrometer (UVAPS) was used to monitor the particle concentration decay rate. The study showed that the deposition rates of fungal spores (Aspergillus niger and Penicillium species) and the other aerosols (canola oil and talcum powder) were similar, especially at very low air exchange rates (in the order of 0.009). Both the aerosol and the bioaerosol deposition rates were found to be a function of particle size. The results also showed increasing deposition rates with increasing ventilation rates, for all particles under investigation. These conclusions are important in understanding the dynamics of fungal spores in the air.

The volatile and hygroscopic properties of diesel nanoparticles were simultaneously determined under a range of engine loads using the volatilization and humidification tandem differential mobility analyzer (VH-TDMA). Additionally, the VH-TDMA was used to measure changes in the hygroscopic behavior of the heterogeneously nucleated diesel nanoparticles as one or more semivolatile species were removed via thermal evaporation or decomposition. Particles produced at high loads exhibited high, dual-step volatility, while those particles produced at low loads were less volatile and exhibited continuous volatilization curves. The hygroscopic growth factor of the particles was shown to be load dependent with high-load particles exhibiting growth factors similar to that of ammonium sulfate. At 85% relative humidity, particles produced at moderate loads exhibited growth factors of approximately 1.1 while low-load particles were shown to be hydrophobic. Growth factors and volatilization temperatures measured for high-load particles clearly indicate that ternary nucleation is involved in particle formation.

Oxidative potential (OP) is related to the organic phase, specifically to its oxygenated organic fraction (OOA). Furthermore, the oxygen content of fuel molecules has significant influence on particulate OP. Thus, this study aimed to explore the actual dependency of the OOA and ROS to the oxygen content of the fuel. In order to reach the goal, different biodiesels blends, with various ranges of oxygen content; have been employed. The compact time of flight aerosol mass spectrometer (c-ToF AMS) enabled better identification of OOA. ROS monitored by using two assays: DTT and BPEA-nit. Despite emitting lower mass, both assays agreed that oxygen content of a biodiesel is directly correlated with its OOA, and highly related to its OP. Hence, the more oxygen included in the considered biodiesels, the higher the OP of PM emissions. This highlights the importance of taking oxygen content into account while assessing emissions from new fuel types, which is relevant from a health effects standpoint.

Microalgae are considered to be one of the most viable biodiesel feedstocks for the future due to their potential for providing economical, sustainable and cleaner alternatives to petroleum diesel. This study investigated the particle emissions from a commercially cultured microalgae and higher plant biodiesels at different blending ratios. With a high amount of long carbon chain lengths fatty acid methyl esters (C20 to C22), the microalgal biodiesel used had a vastly different average carbon chain length and level of unsaturation to conventional biodiesel, which significantly influenced particle emissions. Smaller blend percentages showed a larger reduction in particle emission than blend percentages of over 20%. This was due to the formation of a significant nucleation mode for the higher blends. In addition measurements of reactive oxygen species (ROS), showed that the oxidative potential of particles emitted from the microalgal biodiesel combustion were lower than that of regular diesel. Biodiesel oxygen content was less effective in suppressing particle emissions for biodiesels containing a high amount of polyunsaturated C20–C22 fatty acid methyl esters and generated significantly increased nucleation mode particle emissions. The observed increase in nucleation mode particle emission is postulated to be caused by very low volatility, high boiling point and high density, viscosity and surface tension of the microalgal biodiesel tested here. Therefore, in order to achieve similar PM (particulate matter) emission benefits for microalgal biodiesel likewise to conventional biodiesel, fatty acid methyl esters (FAMEs) with high amounts of polyunsaturated long-chain fatty acids (≥C20) may not be desirable in microalgal biodiesel composition.

The method outlined provides for emission factor measurements to be made for unmodified vehicles driving under real world conditions at minimal cost. The method consists of a plume capture trailer towed behind a test vehicle. The trailer collects a sample of the naturally diluted plume in a 200 L conductive bag and this is delivered immediately to a mobile laboratory for subsequent analysis of particulate and gaseous emissions. The method offers low test turnaround times with the potential to complete much larger numbers of emission factor measurements than have been possible using dynamometer testing. Samples can be collected at distances up to 3 m from the exhaust pipe allowing investigation of early dilution processes. Particle size distribution measurements, as well as particle number and mass emission factor measurements, based on naturally diluted plumes are presented. A dilution profile relating the plume dilution ratio to distance from the vehicle tail pipe for a diesel passenger vehicle is also presented. Such profiles are an essential input for new mechanistic roadway air quality models.

The role of different chemical compounds, particularly organics, involved in the new particle formation (NPF) and its consequent growth are not fully understood. Therefore, this study was conducted to investigate the chemistry of aerosol particles during NPF events in an urban subtropical environment. Aerosol chemical composition was measured along with particle number size distribution (PNSD) and several other air quality parameters at five sites across an urban subtropical environment. An Aerodyne compact Time-of-Flight Aerosol Mass Spectrometer (c-TOF-AMS) and a TSI Scanning Mobility Particle Sizer (SMPS) measured aerosol chemical composition and PNSD, respectively. Five NPF events, with growth rates in the range 3.3–4.6 nm, were detected at two sites. The NPF events happened on relatively warmer days with lower humidity and higher solar radiation. Temporal percent fractions of nitrate, sulphate, ammonium and organics were modelled using the Generalised Additive Model (GAM), with a basis of penalised spline. Percent fractions of organics increased after the NPF events, while the mass fraction of ammonium and sulphate decreased. This uncovered the important role of organics in the growth of newly formed particles. Three organic markers, factors f43, f44 and f57, were calculated and the f44 vs. f43 trends were compared between nucleation and non-nucleation days. f44 vs. f43 followed a different pattern on nucleation days compared to non-nucleation days, whereby f43 decreased for vehicle emission generated particles, while both f44 and f43 decreased for NPF generated particles. It was found for the first time that vehicle generated and newly formed particles cluster in different locations on f44 vs. f43 plot and this finding can be used as a~tool for source apportionment of measured particles.

We have studied the effect of chemical composition of biodiesel fuel on the physical (volatility) and chemical (reactive oxygenated species concentration) properties of nano particles emitted from a modern common-rail diesel engine. Particle emissions from the combustion of four biodiesels with controlled chemical compositions and different varying unsaturation degrees and carbon-chain lengths, together with a commercial diesel, were tested and compared in terms of volatility of particles and the amount of reactive oxygenated species carried by particles. Different blends of biodiesel and petro diesel were tested at several engine loads and speeds. We have observed that more saturated fuels with shorter carbon chain lengths result in lower particle mass but produce particles that are more volatile and also have higher levels of Reactive Oxygen Species. This highlights the importance of taking into account metrics that are relevant from the health effects point of view when assessing emissions from new fuel types.

The charge and chemical composition of ambient particles in an urban environment were determined using a neutral particle and air ion spectrometer and an aerodyne compact time-of-flight aerosol mass spectrometer. Particle formation and growth events were observed on 20 of the 36 days of sampling, with eight of these events classified as strong. During these events, peaks in the concentration of intermediate and large ions were followed by peaks in the concentration of ammonium and sulfate, which were not observed in the organic fraction. Comparison of days with and without particle formation events revealed that ammonium and sulfate were the dominant species on particle formation days while high concentrations of biomass burning OA inhibited particle growth. Analyses of the degree of particle neutralization lead us to conclude that an excess of ammonium enabled particle formation and growth. In addition, the large ion concentration increased sharply during particle growth, suggesting that during nucleation the neutral gaseous species ammonia and sulfuric acid react to form ammonium and sulfate ions. Overall, we conclude that the mechanism of particle formation and growth involved ammonia and sulfuric acid, with limited input from organics.

Particulate emissions from 11 gasoline powered and 2 liquefied petroleum (LPG) powered passenger vehicles were characterised during the Accelerated Simulation Mode driving cycles on a chassis dynamometer. The test fleet consisted of 10 catalyst-equipped vehicles operated with unleaded gasoline (5 Ford Falcons and 5 Holden Commodores), 2 LPG powered vehicles (both Ford Falcons), and 1 older type noncatalyst vehicle operated with leaded gasoline. Particulate characterisation included determination of total particulate number concentration and size distribution using the Scanning Mobility Particle Sizer (SMPS) and the Aerodynamic Particle Sizer (APS). The average particle number concentrations in the SMPS range for all modes was lower for Ford Falcons and somewhat higher for Commodores, with values of 1.5x104 and 4.1x104 cm-3, respectively. This difference is significant and was observed for all modes. The number concentration levels were higher for the LPG fuelled cars (8.4x104 cm-3) and for the leaded gasoline powered vehicle (7.9x105 cm-3). There was not a significant variation in particle count median diameter in the SMPS and the APS ranges, either for different operating conditions of the vehicles investigated, or between different vehicle groups. The observed size distributions were bimodal with average values of CMD ranged from 39.1 to 60.2nm in the SMPS range and from 0.9 to 1.4µm in the APS range. The results obtained from this study can be used as a first order estimation towards emission inventories for vehicle groups included in the investigations.

Generally, the magnitude of pollutant emissions from diesel engines running on biodiesel fuel is ultimately coupled to the structure of the fuel's constituent molecules. Previous studies demonstrated the relationship between the organic fraction of particulate matter (PM) and its oxidative potential. Herein, emissions from a diesel engine running on different biofuels were analyzed in more detail to explore the role that different organic fractions play in the measured oxidative potential. In this work, a more detailed chemical analysis of biofuel PM was undertaken using a compact time of flight aerosol mass spectrometer (c-ToF AMS). This enabled a better identification of the different organic fractions that contribute to the overall measured oxidative potentials. The concentration of reactive oxygen species (ROS) was measured using a profluorescent nitroxide molecular probe 9-(1,1,3,3- tetramethylisoindolin-2-yloxyl-5-ethynyl)-10-(phenylethynyl)anthracene (BPEAnit). Therefore, the oxidative potential of the PM, measured through the ROS content, although proportional to the total organic content in certain cases, shows a much higher correlation with the oxygenated organic fraction as measured by the c-ToF AMS. This highlights the importance of knowing the surface chemistry of particles for assessing their health impacts. It also sheds light onto new aspects of particulate emissions that should be taken into account when establishing relevant metrics for assessing health implications of replacing diesel with alternative fuels. © 2013 American Chemical Society.