Search

A piezoelectric (PE) energy harvesting system with one-cycle maximum power point (MPP) sensing is presented. The one-cycle MPP sensing method uses a very small size sensing capacitor and it can make the transducer output voltage reach the open circuit voltage within one cycle. The proposed MPP sensing block can sense the open circuit voltage with a proposed peak detector and stores the MPP voltage using charge sharing blocks. The one-cycle MPP sensing approach simplifies the design of an MPP tracking algorithm and greatly reduces the tracking time. All control blocks are self-biased and choose the higher voltage between the input or output voltages of the switching converter as a supply voltage (V $_{DD}$ ). Therefore, a voltage multiplexer and a low-power ramp generator with V $_{DD}$ independence are also proposed to control the system without additional DC to DC converter. The entire system has been implemented in a 0.35 µm BCDMOS process. It operates at 90 kHz with a 10-mH inductor. The total power dissipation of the controller is 10 µW at a V $_{DD}$ of 2.7 V. The MPP tracking time is only 9.09 ms/V when the input voltage of the switching converter is changed from 3.4 V to 1.2 V.

Design of low-voltage and efficient energy-harvesting circuits is becoming increasingly important, particularly, for autonomous systems. Since the amount of energy that can be harvested from the surrounding environment is limited, the available output voltage of a harvester is low. Therefore, the design of a low-input-voltage (low-VIN) up-converter is critical to self-powered systems [1-3]. Moreover, the form factor is very constrained in applications such as wearable electronic devices and sensor networks. Recently, low-VIN charge pumps (CPs) for energy harvesting has been compared with DC-DC converters using a large inductor [1-3]. CPs introduced in [1] and [2] use the advanced process technology to push VIN down to the subthreshold region. The CP in [1] introduces a forward-body-biasing (FBB) technique, which improves the voltage conversion efficiency (VCE) for low VIN but shows poor power conversion efficiency (PCE). The CP in [2] achieves the lowest operation voltage. However, the design with a 10-stage CP provides low output power. This paper presents a CP with switching-body-biasing (SBB), adaptive-dead-time (AD), and switch-conductance (SW-G) enhancement techniques to improve the PCE for low VIN as well as to extend the maximum load current.

This paper presents a dc-dc boost converter with the maximum power point tracking (MPPT) technique for thermoelectric energy harvesting applications. The technique realizes variation tolerance by adjusting the switching frequency of the converter. A finely controlled zero-current switching (ZCS) scheme together with the accurate MPPT technique enhances the overall efficiency of the converter because of an optimal turn-on time generated by a one-shot pulse generator that is proposed. Moreover, the ZCS technique can deal with low- and high-temperature differences applied to the thermoelectric generator. This allows a wider range of conversion ratios compared to those of conventional converters used for thermal energy harvesting. Experimentally, the converter implemented in a 0.35-μm BCDMOS process had a peak efficiency of 72% at the input voltage of 500 mV while supplying a 5.62-V output.

Coarse grained arrays (CGAs) with run-time reconfigurability play an important role in accelerating reconfigurable computing applications. It is challenging to design on-chip communication networks (OCNs) for such CGAs with dynamic run-time reconfigurability whilst satisfying the tight budgets of power and area for an embedded system. This paper presents a silicon-proven design of a 64-PE circuit-switched OCN fabric with a dynamic path-setup scheme capable of supporting an embedded coarse-grained processor array. A proof-of-concept test chip fabricated in a 0.13 μm CMOS process occupies a silicon area of 23 mm2 and consumes a peak power of 200 mW @ 128 MHz and 1.2 Vcc, at room temperature. The OCN overhead consumes 9.4% of the area and 18% of the power of the total chip. Experimental results and analysis show that the proposed OCN fabric with its dynamic path-setup is suitable for use in an embedded CGA supporting fast run-time reconfigurability.

This brief presents a regulated charge pump (CP) with an integrated optimum power point tracking (OPPT) algorithm designed for indoor solar energy harvesting. The proposed OPPT circuit does not require a current sensor that consumes power proportionally to the load. The solar cell voltage is regulated at the optimum power point; the CP output is regulated according to the target voltage. The controller of the OPPT circuit and CP dissipates only 450 nW; thus, the proposed technique is appropriate for indoor solar energy harvesting applications under dim lighting conditions.

This paper presents a boost converter with the maximum power point tracking (MPPT) technique for thermoelectric energy harvesting (EH) applications. The technique realizes variation tolerance by adjusting the switching frequency fSW of the converter. A finely controlled zero-current switching (ZCS) scheme together with the accurate MPPT technique enhances the overall efficiency (η) of the converter because of an optimal turn-on time generated by a one-shot pulse generator that is proposed. Moreover, the ZCS technique can deal with low and high temperature differences applied to the thermoelectric generator. Experimentally, the converter implemented in a 0.35 um BCDMOS process had a peak of 72% at the input voltage VIN of 500mV while supplying a 5.62V output.

This paper describes a time-limited power distribution control (TPDC) technique that can be used for single-inductor multiple-output (SIMO) DC-DC converter with many unbalanced loads. Furthermore, the true all-comparator control technique that raises no stability or complexity issues is proposed. This all-comparator technique for SIMO converters is realized only with a single shared hysteresis comparator at a constant switching frequency of 800 kHz. The maximum efficiency reaches 92%. The fabricated chip with 8-channel outputs occupies 2.4×2.1 mm2 in a 0.35-um CMOS process.

This paper presents a low-voltage high-efficiency voltage doubler for thermoelectric energy harvesting. A negative charge pump is used to reduce on-resistance of PMOSFET load switches. Additional circuitry for achieving high efficiency just requires small chip-area and low-cost. The voltage doubler is implemented in 0.13-μm 1.2V CMOS process. The proposed doubler improves the low-voltage power efficiency by 17%, compared to conventional voltage doublers. Moreover, the proposed doubler can support wider load range. The maximum power efficiency reaches 52% at the input voltage of 0.2V.

This paper presents a regulated charge pump (CP) with an integrated optimum power point tracking (OPPT) algorithm designed for indoor solar energy harvesting. The proposed OPPT circuit does not require a current sensor that consumes power proportionally to the load. The solar cell voltage is regulated at the optimum power point; the CP output is regulated according to the target voltage. The controller of the OPPT circuit and CP dissipates only 450nW, so the proposed technique is appropriate for indoor solar energy harvesting applications under dim lighting conditions.

A compact soft-start technique, with an internal circuitry, is presented for the start-up of current mode DC-DC converters for biomedical applications. Examples of medical applications in DC-DC converters include bio-patch, wireless medical sensor node, RFID applications and medical instruments that must have a high stability. To achieve this, a soft-start circuit is proposed to prevent inrush current and output voltage overshoot, during the start-up of the current mode DC-DC converters. The output of the error amplifier is controlled by a stair-case waveform signal generator during the start-up period. The proposed soft-start circuit is fully integrated on chip for portable and wireless medical devices, so that the external components are not required, leading to a reduction in the PCB space and cost. The new soft-start circuit which is digitally-controlled unlike conventional ones was fabricated in a CMOS 0.35-µm process and occupies an active area of 0.19 mm2 with a 3.3 V supply voltage.