Search

The aim of this work is to develop a tool to predict some pulp properties e.g., pulp yield, Kappa number, ISO brightness (ISO 2470:2008), fiber length and fiber width, using the sapwood and heartwood proportion in the raw-material. For this purpose, Acacia melanoxylon trees were collected from four sites in Portugal. Percentage of sapwood and heartwood, area and the stem eccentricity (in N-S and E-W directions) were measured on transversal stem sections of A. melanoxylon R. Br. The relative position of the samples with respect to the total tree height was also considered as an input variable. Different configurations were tested until the maximum correlation coefficient was achieved. A classical mathematical technique (multiple linear regression) and machine learning methods (classification and regression trees, multi-layer perceptron and support vector machines) were tested. Classification and regression trees (CART) was the most accurate model for the prediction of pulp ISO brightness (R = 0.85). The other parameters could be predicted with fair results (R = 0.64–0.75) by CART. Hence, the proportion of heartwood and sapwood is a relevant parameter for pulping and pulp properties, and should be taken as a quality trait when assessing a pulpwood resource. info:eu-repo/semantics/acceptedVersion

Submitted by Maria Eduarda Pereira Rodrigues (erodrigues@ipcb.pt) on 2016-02-18T12:18:20Z No. of bitstreams: 1 BioRes_11_1_1892_GarciaGonzalo_SMPSGA_Prediction_Softwood_Paper_Props_Density_Regression_8080.pdf: 885317 bytes, checksum: a53ab4c4bcb7710090b598a213c3ce5f (MD5) Approved for entry into archive by Maria Eduarda Pereira Rodrigues (erodrigues@ipcb.pt) on 2016-02-18T16:00:29Z (GMT) No. of bitstreams: 1 BioRes_11_1_1892_GarciaGonzalo_SMPSGA_Prediction_Softwood_Paper_Props_Density_Regression_8080.pdf: 885317 bytes, checksum: a53ab4c4bcb7710090b598a213c3ce5f (MD5) Made available in DSpace on 2016-02-18T16:00:40Z (GMT). No. of bitstreams: 1 BioRes_11_1_1892_GarciaGonzalo_SMPSGA_Prediction_Softwood_Paper_Props_Density_Regression_8080.pdf: 885317 bytes, checksum: a53ab4c4bcb7710090b598a213c3ce5f (MD5) Previous issue date: 2016

In this paper, the morphological properties of fiber length (weighted in length) and of fiber width of unbleached Kraft pulp of Acacia melanoxylon were determined using TECHPAP Morfi® equipment (Techpap SAS, Grenoble, France), and were used in the calibration development of Near Infrared (NIR) partial least squares regression (PLS-R) models based on the spectral data obtained for the wood. It is the first time that fiber length and width of pulp were predicted with NIR spectral data of the initial woodmeal, with high accuracy and precision, and with ratios of performance to deviation (RPD) fulfilling the requirements for screening in breeding programs. The selected models for fiber length and fiber width used the second derivative and first derivative + multiplicative scatter correction (2ndDer and 1stDer + MSC) pre-processed spectra, respectively, in the wavenumber ranges from 7506 to 5440 cm−1. The statistical parameters of cross-validation (RMSECV (root mean square error of cross-validation) of 0.009 mm and 0.39 μm) and validation (RMSEP (root mean square error of prediction) of 0.007 mm and 0.36 μm) with RPDTS (ratios of performance to deviation of test set) values of 3.9 and 3.3, respectively, confirmed that the models are robust and well qualified for prediction. This modeling approach shows a high potential to be used for tree breeding and improvement programs, providing a rapid screening for desired fiber morphological properties of pulp prediction. info:eu-repo/semantics/publishedVersion

Aim of the study: The ability of NIR spectroscopy for predicting the ISO brightness was studied on unbleached Kraft pulps of Acacia melanoxylon R. Br.Area of study: Sites covering littoral north, mid interior north and centre interior of Portugal.Materials and methods: The samples were Kraft pulped in standard identical conditions targeted to a kappa number of 15. A Near Infrared (NIR) partial least squares regression (PLSR) model was developed for the ISO brightness prediction using 75 pulp samples with a variation range of 18.9 to 47.9 %.Main results: Very good correlations between NIR spectra and ISO brightness were obtained. Ten methods were used for PLS analysis (cross validation with 48 samples), and a test set validation was made with 27 samples. The 1stDer pre-processed spectra coupling two wavenumber ranges from 9404 to 7498 cm-1 and 4605 to 4243 cm-1 allowed the best model with a root mean square error of ISO brightness prediction of 0.5 % (RMSEP), a r2 of 99.5 % with a RPD of 14.7.Research highlights: According to AACC Method 39-00, the present model is sufficiently accurate to be used for process control (RPD ≥ 8).Key words: Acacia melanoxylon; unbleached Kraft pulps; ISO Brightness; NIR; RPD.

The pulping properties of cypress species are not known and the present paper aims to filling this gap. Namely, Cupressus lusitanica Mill., C. sempervirens L. and C. arizonica Greene have been submitted to kraft pulping and the pulp properties are compared with those of Pinus pinaster Aiton. and P. sylvestris Watereri as references. Schopper Riegler degree, density, Bekk’s smoothness, tensile index, tear index, burst index, stretch, dry zero-span strength, wet zero-span strength, brightness, opacity and light scattering coefficient have been tested. The pulp yields and delignification degrees of cypress woods were lower than those of the pine references. Fibre length, width and coarseness were statistically different between pines and cypress species and C. sempervirens pulps have corresponding data close to those of pine species. Cypress pulps can be refined much faster than pine pulps. The papers sheets of cypress fibres have, in general, lower mechanical performance than those of pine fibres. Papers from C. arizonica and C. lusitanica are similar and C. sempervirens has intermediate properties being between the other cypress and pine species. However, cypress fibres are relatively short, flexible and collapsible and can be refined with low energy demand, and thus could be incorporated into papers resulting in products with better light scattering and smoothness.

Wood density and pulp yield are key parameters in the evaluation of tree productivity and quality for pulping and their relationships are of high practical importance. The influence of wood density on pulp yield and other pulp quality parameters was investigated using Acacia melanoxylon and its natural variability as a case study. Twenty trees were harvested (five trees in each of four sites in Portugal), and wood discs taken at different height levels, from the base to the top of the tree, providing 100 wood samples, covering the natural variability of wood density ranging from 449 kg m−3 to 649 kg m−3. Under the same experimental conditions of kraft pulping, screened pulp yield ranged 47.0–58.2 %, Kappa number 10.9–18.4, ISO brightness 14.9–45.6, fibre length 0.660–0.940 mm and fibre width 16.2–22.9 μm. The pulp yield and Kappa number were not correlated with wood density. Higher pulp yields were associated with lower Kappa numbers and alkali consumption, suggesting the important role of chemical composition of wood on kraft cooking. The results confirm the high pulping potential of Acacia melanoxylon trees grown in Portugal and suggest the possibility of tree selection using both wood density and pulp yield.

Paper properties determine the product application potential and depend on the raw material, pulping conditions, and pulp refining. The aim of this study was to construct mathematical models that predict quantitative relations between the paper density and various mechanical and optical properties of the paper. A dataset of properties of paper handsheets produced with pulps of Acacia dealbata, Acacia melanoxylon, and Eucalyptus globulus beaten at 500, 2500, and 4500 revolutions was used. Unsupervised classification techniques were combined to assess the need to perform separated prediction models for each species, and multivariable regression techniques were used to establish such prediction models. It was possible to develop models with a high goodness of fit using paper density as the independent variable (or predictor) for all variables except tear index and zero-span tensile strength, both dry and wet. info:eu-repo/semantics/publishedVersion