Search

The adsorption of locust bean gum (LBG) onto Northern Bleached Softwood Kraft (NBSK) pulp improved paper tensile and burst strength and lowered refining energy by strengthening inter-fibre bonding. Adsorption kinetics and isotherms were investigated to develop a fundamental understanding of the adsorption mechanism. The adsorption rate followed pseudo-second-order kinetics and the activation energy was 99.34 kJ·mol−1, suggesting chemisorption. The adsorption rate constant increased rapidly with temperature from 25 to 45 °C (k = 1.93 to 24.03 g·mg−1·min−1), but the amount adsorbed at equilibrium decreased (qe = 1.91 to 0.48 mg·g−1 o.d. fibre). LBG adsorption to NBSK at 25 °C was consistent with the Langmuir adsorption model for LBG n = 5.00, and the equilibrium constant Kf = 2.57 mg·g−1·(mg·L−1)−1/n at 25 °C. Favorable adsorption conditions for negatively charged LBG were identified: 25 °C for 10 min, low dosage level ( 150 r.p.m.), acidic or neutral conditions (pH 2–7) without salt addition. Graphic abstract

Introduction. The Shchuchiy Bay is located in the western part of the skerry area of Lake Ladoga near the town of Priozersk. For almost 20 years, the bay has experienced an anthropogenic impact from the ingress of untreated wastewater from the Priozersk Pulp and Paper Mill (PPM). Systematic microbiological studies of the Shchuchiy Bay ecosystem were started in the middle of the 1970s by the Institute of Limnology of the Russian Academy of Sciences and continued after the PPM closure in 1986. Materials and methods. The ecosystem of the bay was studied in detail during the growing season of 2013–2014; periodic studies were carried out in 2015–2018. Retrospective data were also used for the analysis. Water samples were taken at four stations from the surface horizon. The following microbiological indicators were determined: the abundance of bacterioplankton and the percentages of various morphological types of bacterial cells. Results and discussion. A comparison of the quantitative level of development of the bacterial community in the bay in different periods showed a gradual decrease in the abundance of bacterioplankton as the anthropogenic impact weakened after the closure of the Priozersky PPM from 12.40 million cells ml–1 in 1987 to an average value of 2.62±1.03 million cells ml–1 in 2013–2018. A positive correlation was found between the concentration of bacteria and water temperature. The percentage of rod-shaped microorganisms in the water of the bay also decreased as the anthropogenic impact weakened from 73.4 % in 1987 to 53.1±7.6 % in 2013–2018, which indicated an improvement in water quality. Conclusion. A stable decrease in the abundance of bacteria from the level characteristic of highly polluted and eutrophic water bodies to the level characteristic of mesotrophic and mesotrophic-eutrophic water bodies is a reliable criterion for the restoration of the ecosystem of the Shchuchiy Bay to the state characteristic of similar bays of Lake Ladoga.

The sorption properties of organomineral composite sorbents have been investigated by ICP-MS method. The diatomite of the Jradzor deposit and bentonite of the Sarigyuh deposit (Armenia) were used as inorganic constituents. Diatomite serves as a structure-forming component and provides mass transfer due to its high porosity (V = 2.0 cm3/g) and large pore sizes (150–200 nm). Bentonite is responsible for the functionality of the sorbents. The organic component is also responsible for the functionality of the obtained sorbents. Paper pretreated with acids (nitric and phosphoric) was used as an organic component. A synthetic solution containing cations of heavy metals was used as an object of study. The experiments were carried out in static mode on a Jar-Test device.

The pulp and paper industry is primarily dependent on fibrous wood for pulp and paper production. However, this over-dependence on fibrous wood poses serious environmental challenges such as the diminishing of the fibrous wood stocks, deforestation, emission of greenhouse gases, and global warming. Therefore, to mitigate these environmental challenges associated with its utilization for paper and pulp production, other sustainable raw material sources can also be considered for the production of paper and pulp. There are enormous benefits associated with the utilization of non-wood fibres as an alternative and sustainable raw materials source for the production of paper and pulp. These benefits have in the recent past prompted millers in China, India, Brazil, and the USA to consider the utilization of non-wood fibres in paper and pulp production. In Kenya, the pulp and paper industry is very much dependent on fibrous wood for production and the industry is yet to fully embrace the utilization of nonwood fibres for paper and pulp production. Further, the dependence on fibrous wood has contributed significantly to the decline of paper pulp and paper production, deforestation, and rise in paper importations due to insufficient raw material supplies. The importation of paper and pulp products has further led to the collapse of the paper industry in Kenya. The sector stands a chance of revival and vibrancy through the utilization of the abundant agricultural residues and feedstocks lying in the agricultural fields across the country. Similar experiences elsewhere have proved that the abundance of agricultural waste can be utilized for the production of paper and pulp due to their excellent fibre content for specialty papers, and easy pulpability. The agricultural residues are therefore considered a quintessential alternative and sustainable source of raw materials for the pulp and paper industry. Moreover, their utilization will mitigate environmental impacts such as deforestation, climate change, and pollution .

High per- and polyfluorinated alkyl substance (PFAS) concentrations have been detected in agricultural soils in Southwest Germany. Discharges of PFAS-contaminated paper sludge and compost are suspected to be the cause of the contamination. Perfluorinated carboxylic acids (PFCAs) have been detected also in groundwater, drinking water, and plants in this area. Recently, previously unknown compounds have been identified by high-resolution mass spectrometry (HRMS). Major contaminants were polyfluorinated dialkylated phosphate esters (diPAPs) and N-ethyl perfluorooctane sulfonamide ethanol–based phosphate diester (diSAmPAP). In this study, HRMS screening for PFAS was applied to 14 soil samples from the contaminated area and 14 impregnated paper samples which were from a similar period than the contamination. The paper samples were characterized by diPAPs (from 4:2/6:2 to 12:2/12:2), fluorotelomer mercapto alkyl phosphates (FTMAPs; 6:2/6:2 to 10:2/10:2), and diSAmPAP. In soil samples, diPAPs and their transformation products (TPs) were the major contaminants, but also FTMAPs, diSAmPAP, and their TPs occurred. The distribution patterns of the carbon chain lengths of the precursor PFAS in soil samples were shown to resemble those in paper samples. This supports the hypothesis that paper sludge is a major source of contamination. The presence of major degradation products like PFCAs, FTSAs, or PFOS and their distribution of carbon chain lengths indicate the activity of biotic or abiotic degradation processes and selective leaching processes from the upper soil horizons. Graphical abstract Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03463-9.

The paper presents a research on the disposal of the toxic waste of pulp and paper mill (sludge-lignin with the empirical formula CH1.51N0.05S0.03Cl0.01O0.54through its oxidation in supercritical water-oxygen fluid, including the case of using methane as a co-fuel. The experiments were carried out with a flow reactor of original design at a pressure of 25 MPa, temperature gradient along the vertical axis (from top to bottom: 390–600°C), and variation in the flow rate of the sludge-lignin (with the addition of NaOH, 1.6 wt %), oxygen, and methane. The experiments yielded data on the content of phenols in the water and the composition of the gaseous products collected at the outlet of the reactor versus the oxygen excess ratio. From these data, as well as the time dependences of the reactor wall temperature and the power of the ohmic heaters, it follows that using distributed supply of methane to compensate for the energy for heating of the reagents is preferable as compared with local inlet of methane to the upper part of the reactor. It has been shown that the addition of methane makes it possible to reduce the oxygen excess required for complete oxidation of the organic components of sludge-lignin.

The fibre characteristics of five Spondia mombin stands were studied to determine their suitability for pulp and paper production. Wood slivers obtained parallel to grain at three (3) different positions along the bole were macerated in combined identical amounts of glacial acetic acid plus hydrogen peroxide under heat at between 80-100o C. Macerated fibres were washed clean of mixture and mounted on slide for microscopic examination of fibre characteristics. Completely Randomized Design (CRD) was employed for the experiment. Data were analysed using one-way Analysis of Variance (ANOVA) while, the Duncan’s Multiple Range Test (DMRT) was used to separate means of significant differences among the treatments. Results show that significant differences existed in fibre characteristic of sampled trees, however the fibre length ranged from 0.98-1.0 mm, fibre diameter (18.22-21.47 um), lumen width (10.90-12.98 um) and cell wall thickness (3.86-4.60 um). Significant differences were also observed among the derived fibre characteristics, the Runkel ratio ranged from 0.66-8.89, elasticity coefficient (57.22-60.50 %), coefficient of rigidity (19.78-22.24 %), slenderness ratio (43.27-46.5). This implied that, the fibres of S. mombin were short and elastic which make the wood species an appropriate raw material for pulp and paper making especially when blended with other long fibre species.

The potential of alkaline cellulo-xylanolytic enzymes from non-pathogenic Bacillus subtilis strain was tested for deinking of photocopier waste paper. Cellulase and xylanase play a crucial role in deinking of different types of waste paper. Partial purification of cellulo-xylanolytic enzymes was carried out using ultrafiltration followed by ammonium sulfate precipitation. The ultrafiltered enzyme was used for deinking the photocopier waste paper along with chemical deinking. An enzyme dose of 0.6 IU/g and reaction time of 60 min for ultrafiltered cellulo-xylanolytic enzyme significantly increased deinking efficiency, tear index (9.52%) and folding endurance (5±2%) as compared to chemical deinking. There was improvement in strength properties such as tear index and double-fold along with freeness of pulp (18%). There was slight decrease in tensile index (0.6%) and burst index (16%) while ISO brightness remained unaffected. Enzymatic deinking (74.3%) by ultrafiltered cellulo-xylanolytic from Bacillus subtilis was found significant over conventional chemical deinking.

Today the print quality of digital printing techniques has improved and is considered satisfactory and competitive to analogue techniques for certain graphic products. Satisfactory print quality mostly depends on the interaction of ink and printing substrate where ink penetration has an important role. Namely, the ink penetration affects the parameters that describe the print quality together with visual appearance of print density and mottling. Therefore, it is important to select an adequate printing substrate for each printing technique. Awareness of environmental problems related to the shortage of wood raw materials has led to an increase in the use of recycled printing paper and in particular the implementation of new alternative sources of cellulose fibres instead of virgin wood fibres in the papermaking process. In this research the emphasis is precisely on defining the influence of ink penetration into laboratory papers made of triticale pulp on the final print quality. The laboratory printing papers were obtained by mixing triticale pulp with pulp from recycled fibres in three different portions. Papers were thereafter printed by ultraviolet (UV) inkjet printer and the ink penetration within laboratory papers with and without straw pulp was analysed using two methods of ink penetration analysis (microscopic/spectroscopic). The influence of ink penetration on the final print quality was observed and analysed based on several quality parameters (optical ink density, mottling and colorimetric values). These results confirmed that triticale pulp in laboratory papers provides equal print quality compared to laboratory papers made only from pulp from recycled fibres.

Cellulose based nanomaterials have the great potential to be applied to paper as bulk additive or coating material to improve overall final properties, especially in secondary fiber. In the present work, the effect of applying different kinds of cellulose nanofibrils (CNF) to papers obtained from recycled fibers using size press on physical, mechanical and barrier properties was investigated and compared with the sole use of starch as coating material. The coating process of CNF was carried out by the addition of size press grade starch to coating suspension. As a cellulose source, wheat straw was evaluated and CNF was obtained through oxidative and enzymatic pretreatments. Results indicate that starch/CNF suspension improves the overall paper properties. As a result of the deposition of coating suspension contains of 4 % wt. periodate-oxidized CNF onto paper surface, tensile and burst indices of papersheets increased as 52.2 % and 194.4 %. Significant decreases were observed in air permeability as 69.8 %. Compression tests also have been conducted to evaluate papersheets end-use properties. In comparison to the other pretreated CNF, due to is lower viscosity, applying periodate-oxidized CNF as size press significantly increased the mechanical properties of the papers fabricated from the recycled pulps. TUBITAK-TEYDEBTurkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [1505]; Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate [1505, 5180044] This work was supported by TUBITAK-TEYDEB 1505 (The Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate 1505), Project No. 5180044. WOS:000703585400013 2-s2.0-85108063350

In this study, it was aimed to investigate the chemical and morphological suitability of using pseudo-stem which are formed in large amounts during the fruit harvesting of the banana plant (Musa sapientum) with a widespread agricultural area in the world, as raw material in the paper industry. The main chemical constituents of banana pseudo-stem holocellulose, α-cellulose and lignin were determined as %77.5, %51.0 and %12.7, respectively. Hot water solubility was 17.3%, cold water solubility 13.0%, alcohol and 1% NaOH solubility values were 9.2% and 33.3%, respectively. It has been determined that banana pseudo-stem waste fibers, which are similar to softwood fibers in terms of fiber length and hardwood fibers in terms of fiber width, have high slenderness and flexibility ratios with low Runkel ratio, rigidity coefficient and Mühlstep ratio. The results obtained from chemical and morphological analyzes indicated that banana pseudo stem waste is a suitable raw material for pulp and paper production., Bu çalışmada dünyada yaygın bir tarım alanına sahip muz bitkisinin (Musa sapientum) meyve hasadı sırasında oldukça fazla miktarda oluşan gövde atıklarının, kağıt endüstrisinde hammadde olarak kullanılabilirliğinin kimyasal ve morfolojik açıdan uygunluğunun araştırılması amaçlanmıştır. Muz yalancı gövdesinin başlıca kimyasal bileşenleri holoselüloz, α-selüloz ve lignin sırasıyla %77.5, %51.0 ve %12.7 olarak tespit edilmiştir. Sıcak su çözünürlüğü %17.3, soğuk su çözünürlüğü %13.0, alkol ve %1 NaOH çözünürlük değerleri ise sırasıyla %9.2 ve %33.3 olarak bulunmuştur. Lif uzunluğu bakımından iğne yapraklı ağaç odunu liflerine, lif genişliği bakımından ise yapraklı ağaç odunu liflerine benzeyen muz yalancı gövde atığı liflerinin düşük Runkel oranı, rijitlik katsayısı ve Mühlstep oranı ile yüksek narinlik ve esneklik oranlarına sahip olduğu tespit edilmiştir. Kimyasal ve morfolojik analizlerden elde edilen sonuçlar, muz yalancı gövde atıklarının kağıt hamuru ve kağıt üretimi için uygun bir hammadde olduğunu göstermiştir.

This study optimizes a novel surfactant-assisted green liquor dregs (GLD) pretreatment of paper mill sludge (PMS), both of which are wastes from the kraft pulping industry, using a combined Response Surface Methodology (RSM) design. Optimized conditions give a maximal reducing sugar release of 16.38 g/L. A substantial reduction in heavy metals aluminum, chromium, cobalt, arsenic, lead, and copper after pretreatment illustrates the enhancement of substrate digestibility by reducing toxic elements. Separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) for hydrogen production are assessed. SSF produced a hydrogen yield of 3.72 mL/g, displaying a 36.26% increase from pretreated PMS compared to SHF. These findings provide insights into possible methods of reducing process duration, energy input, and costs incurred with waste disposal within the paper industry. Furthermore, improved hydrogen yield using an SSF process demonstrates the potential beneficiation of pulp and paper GLD and PMS wastes.

Fraudulent papers from paper mills are a serious threat to the entire scientific community. Naunyn-Schmiedeberg’s Archives of Pharmacology has become the target of a massive attack of fraudulent papers originating from paper mills. This editorial highlights 20 important features we observed with paper mills and explains how the journal is responding to this serious threat to restore the integrity of science. Hopefully, this editorial is also helpful for editors of other scientific journals.