Search

Cement plants are responsible for particle and gaseous emissions into the atmosphere. With respect to particle emission, the greater part of is in the range from 0.05 to 5.0 µm in diameter. In the last years attention was paid to submicron particles, but there is a lack of available data on the emission from stationary sources. In this paper, concentration and size distribution of particles emitted from four cement kilns, in relationship to operational conditions (especially the use of alternative fuel to coal) of the clinker process are reported. Experimental campaigns were carried out by measuring particles concentration and size distribution at the stack of four cement plants through condensation particle counter (CPC) and scanning mobility particle sizer spectrometer (SMPS). Average total particle number concentrations were between 2000 and 4000 particles/cm3, about 8–10 times lower that those found in the corresponding surrounding areas. As for size distribution, for all the investigated plants it is stable with a unimodal distribution (120–150 nm), independent from the fuel used. Implications: The study provides information on submicron particles emitted from cement kilns in different driving conditions. In particular, the total particle number is modest and considerably lower than that measured in ambient air, whereas the particle size distribution could be influenced by the operational conditions. [ABSTRACT FROM AUTHOR]

Nitrous oxide (N2O) is the third most important greenhouse gas after carbon dioxide and methane, and contributes about 6% to the greenhouse effect. Nitrous oxide is a minor component of the atmosphere, and it is a thousand times less than carbon dioxide (CO2). Nevertheless, it is much more potent than CO2and methane, owing to its long stay in the atmosphere of approximately 120 yr and the high global warming potential (GWP) of 298 times that of CO2. Although greenhouse gases are natural in the atmosphere, human activities have changed the atmospheric concentrations. Most of the values of emission of nitrous oxide are still obtained by means of emission factors and not actually measured; the lack of real data may result in an underestimation of current emissions. The emission factors used for the calculation of N2O can be obtained from the “Guidelines for the implementation of the national inventory of emissions” of the Intergovernmental Panel on Climate Change, which refer to all nations for the realization of their inventory. This study will present real data, measured in several Italian cement plants with different characteristics. The work also shows a comparison between N2O concentration measured with in situ Fourier transform IR (FTIR) and the reference method EN ISO 21258 based on nondispersive IR (NDIR), in order to investigate the interfering compounds in the measurement with NDIR.Implications:N2O may arise as an unwanted by-product of nitrogen oxide (NOx) abatement systems, in particular selective noncatalytic reduction (SNCR). Since it is applied in the cement plants, N2O emission from cement industry is evaluated, with both FTIR and NDIR instrument. Several considerations emerged from the results. First of all, the emission from this industrial sector is not negligible, and for that reason N2O concentration should be regulated; another observation is that the reference method based on the NDIR technique is not as selective as FTIR could be. [ABSTRACT FROM PUBLISHER]

A method to measure the emissive concentration of 5-ethylidene-2-norbornene (ENB), a reactive compound used in industrial synthesis of terpolymers, has been developed. The starting points for the development of the presented method are European and Italian reference methods for the quantification of nonreactive volatile organic compounds in industrial emission. In this study, sampling conditions and desorption solvent have been optimized in laboratory and the method was applied in an industrial plant. The laboratory tests showed a good recovery (88-95 %). The concentrations of ENB in industrial emission obtained with the developed method were compared with an online gas chromatography-flame ionization results ( R > 0.97). In addition, several manual measurements were performed in parallel, and the resulting %RSD repeatability was <9 %. The developed method provides a discontinuous technique to measure reactive volatile organic compounds using easy-to-use instruments and assures a very good accuracy and precision even with high-humidity gas flows. The method could be extended to other reactive compounds of the same class. [ABSTRACT FROM AUTHOR]

Active carbon-based sorbents are well known and are used in analytical chemistry. Activated carbon fibers (ACFs) are mainly used as abatement systems in industrial emission pollution control. The objective of this study was to extend the use of ACFs in analytical chemistry for the analysis of polychlorodibenzo-p-dioxins (PCDDs), polychlorodibenzofurans (PCDFs), dioxin-like polychlorobiphenyls (PCBs), and chlorobenzenes (CBs). For this purpose, the extraction efficiency was evaluated based on the QA/QC criteria defined by EPA/ISO reference methods on 13C-standards recovery rates. The procedures tested were ultrasonic assisted extraction (UAE), Soxhlet extraction (SE), accelerated solvent extraction (ASE), and microwave-assisted extraction (MAE). Each experiment was performed in triplicate to ensure the repeatability of the results, and a second extraction assessed the complete extraction. The comparison of the results of each set of experiments with the minimum requirements of the reference methods for each class of compounds led to SE being chosen as the best technique. SE with toluene resulted in a reduction of time and costs and with respect to the other investigated techniques. The present work demonstrated that ACFs can be used in environmental fields means of both prevention and control (exploiting the adsorbent characteristics) and for analytical purposes (exploiting the desorption) for the described chlorinated classes of pollutants. [ABSTRACT FROM AUTHOR]

A monitoring campaign of polychlorinated dibenzop- dioxins and dibenzofurans, polyaromatic hydrocarbons (PAHs), and polychlorinated biphenyl was carried out in an Italian iron ore sintering plant by sampling the combustion gases at the electrostatic precipitator (ESP) outlet, at the Wetfine scrubber (WS) outlet, and by collecting the ESP dust. Few data are available on these micropollutants produced in iron ore sintering plants, particularly from Italian plants. This study investigates the PAH emission profiles and the removal efficiency of ESPs and WS. PAHs were determined at the stack, ESP outlet flue gases, and in ESP dust to characterize the emission profiles and the performance of the ESP and the WS for reducing PAH emission. The 11 PAHs monitored are listed in the Italian legislative decree 152/2006. The mean total PAH sum concentration in the stack flue gases is 3.96 μg/N · m3, in ESP outlet flue gases is 9.73 μg/N · m3, and in ESP dust is 0.53 μg/g. Regarding the emission profiles, the most abundant compound is benzo(b)fluoranthene, which has a relative low BaP toxic equivalency factors (TEF) value, followed by dibenzo(a,l)pyrene, which has a very high BaP(TEF) value. The emission profiles in ESP dust and in the flue gases after the ESP show some changes, whereas the fingerprint in ESP and stack flue gases is very similar. The removal efficiency of the ESP and of WS on the total PAH concentration is 5.2 and 59.5%, respectively. [ABSTRACT FROM AUTHOR]

An experimental campaign was carried out on a hospital and cemetery waste incineration plant in order to assess the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs). Raw gases were sampled in the afterburning chamber, using a specifically designed device, after the heat recovery section and at the stack. Samples of slags from the combustion chamber and fly ashes from the bag filter were also collected and analyzed. PCDD/Fs and PAHs concentrations in exhaust gas after the heat exchanger (200–350°C) decreased in comparison with the values detected in the afterburning chamber. Pollutant mass balance regarding the heat exchanger did not confirm literature findings about the de novo synthesis of PCDD/Fs in the heat exchange process. In spite of a consistent reduction of PCDD/Fs in the flue gas treatment system (from 77% up to 98%), the limit of 0.1ngITEQNm−3 at the stack was not accomplished. PCDD/Fs emission factors for air spanned from 2.3 up to 44μgITEQt−1 of burned waste, whereas those through solid residues (mainly fly ashes) were in the range 41–3700μgITEQt−1. Tests run with cemetery wastes generally showed lower PCDD/F emission factors than those with hospital wastes. PAH total emission factors (91–414μgkg−1 of burned waste) were in the range of values reported for incineration of municipal and industrial wastes. In spite of the observed release from the scrubber, carcinogenic PAHs concentrations at the stack (0.018–0.5μgNm−3) were below the Italian limit of 10μgNm−3. [Copyright &y& Elsevier]