Search

Microwave photonic (MWP) filters using on-chip stimulated Brillouin scattering offer great potential for next-generation radio frequency (RF) applications due to the unprecedented high spectral resolution, flexible programmability, and ultra-wideband frequency agility. Although impressive functionalities have been reported, limited link performance, due to the amplification noise induced by the Brillouin gain process, hinders the practical deployment in existing RF applications. In this paper, we present the first comprehensive numerical and experimental study of chip-based Brillouin MWP bandpass filters implemented in a range of link configurations. In the experiments, key RF performance figures of merit, including link gain, noise figure, passband resolution, bandwidth tunability, and passband extinction of chip-based Brillouin filters are experimentally investigated and numerically analyzed. This comprehensive study points out a preferable filter scheme with optimized system-level performance. The numerical model developed in this paper allows for extrapolations to further improve the performance. The systematic work establishes a feasible design route for achieving high link-performance chip-based Brillouin microwave photonic bandpass filters.

LIDAR on a silicon chip holds strong potentials for LIDAR system solutions featuring low cost, small size, and high robustness. In line with this effort, on-chip circulators are of great interest as they bring significant benefit for system complexity reduction and SNR improvement by enabling the LIDAR transmitter and receiver to share a single common aperture. Here, we present our recent study on passive silicon photonics nonlinear switches as conditional circulators for LIDAR applications. We propose a device implementation to address the nonlinear switch working principle by controlling waveguide nonlinear coefficient using sub-wavelength gratings. This implementation is foundry-compatible using only regular passive silicon waveguide components and are fully demonstrated in the experiment. In addition, we propose a sub-splitting coupler-based switch potentially can achieve a better fabrication tolerance than sub-wavelength grating-based switch. This work builds up signal processing functions in silicon photonics technology for optical communication and sensing applications. In particular, for LIDAR applications, this work contributes to the critical components of important use, and the easy integration with other existing functions such as optical phased arrays and spectral filters pronounces the potential for LIDAR on a silicon chip.

Integrated optical signal processors have been identified as a powerful engine for optical processing of microwave signals. They enable wideband and stable signal processing operations on miniaturized chips with ultimate control precision. As a promising application, such processors enables photonic implementations of reconfigurable radio frequency (RF) filters with wide design flexibility, large bandwidth, and high-frequency selectivity. This is a key technology for photonic-assisted RF front ends that opens a path to overcoming the bandwidth limitation of current digital electronics. Here, the recent progress of integrated optical signal processors for implementing such RF filters is reviewed. We highlight the use of a low-loss, high-index-contrast stoichiometric silicon nitride waveguide which promises to serve as a practical material platform for realizing high-performance optical signal processors and points toward photonic RF filters with digital signal processing (DSP)-level flexibility, hundreds-GHz bandwidth, MHz-band frequency selectivity, and full system integration on a chip scale., Nanophotonics, 7 (2), ISSN:2192-8614

We present a Nyquist-filtering optical (de)multiplexer using a ring resonator-assisted interferometer circuit. It features a near-rectangular passband spectrum, scalable port count, and can be designed with sub-GHz spectral resolution. The circuit can be constructed using ordinary passive photonic-integrated circuit building blocks. In contrast to its counterparts using tapped-delay-line circuit topologies, this circuit has a chip area two-orders-of-magnitude smaller. The results of this study show the potential for realizing high-spectral-efficiency multicarrier transceivers and reconfigurable optical add-drop multiplexers in a fully integrated form.

Recently, there has been a growing interest in deploying smart materials as sensing components of structural health monitoring systems. In this arena, piezoelectric materials offer great promise for researchers to rapidly expand their many potential applications. The main goal of this study is to review the state-of-the-art piezoelectric-based sensing techniques that are currently used in the structural health monitoring area. These techniques range from piezoelectric electromechanical impedance and ultrasonic Lamb wave methods to a class of cutting-edge self-powered sensing systems. We present the principle of the piezoelectric effect and the underlying mechanisms used by the piezoelectric sensing methods to detect the structural response. Furthermore, the pros and cons of the current methodologies are discussed. In the end, we envision a role of the piezoelectric-based techniques in developing the next-generation self-monitoring and self-powering health monitoring systems.

Radio frequency (RF) switches are essential for implementing routing of RF signals. However, the increasing demand for RF signal frequency and bandwidth is posing a challenge of switching speed to the conventional solutions, i.e., the capability of operating at a sub-nanosecond speed or faster. In addition, signal frequency reconfigurability is also a desirable feature to facilitate new innovations of flexible system functions. Utilizing microwave photonics as an alternative path, we present here a photonic implementation of an RF switch providing not only the capability of switching at a sub-nanosecond speed but also options of frequency doubling of the input RF signals, allowing for flexible output waveforms. The core device is a traveling-wave silicon modulator with a device size of 0.2 mm × 1.8 mm and a modulation bandwidth of 10 GHz. Using microwave frequencies, i.e., 15 GHz and 20 GHz, as two simultaneous RF input signals, we experimentally demonstrated their amplitude and frequency switching as well as that of the doubled frequencies, i.e., 30 GHz and 40 GHz, at a switching frequency of 5 GHz. The results of this work point to a solution for creating high-speed RF switches with high compactness and flexibility.

Optical delay lines implemented in photonic integrated circuits (PICs) are essential for creating robust and low-cost optical signal processors on miniaturized chips. In particular, tunable delay lines enable a key feature of programmability for the on-chip processing functions. However, the previously investigated tunable delay lines are plagued by a severe drawback of delay-dependent loss due to the propagation loss in the constituent waveguides. In principle, a serial-connected amplifier can be used to compensate such losses or perform additional amplitude manipulation. However, this solution is generally unpractical as it introduces additional burden on chip area and power consumption, particularly for large-scale integrated PICs. Here, we report an integrated tunable delay line that overcomes the delay-dependent loss, and simultaneously allows for independent manipulation of group delay and amplitude responses. It uses a ring resonator with a tunable coupler and a semiconductor optical amplifier in the feedback path. A proof-of-concept device with a free spectral range of 11.5 GHz and a delay bandwidth in the order of 200 MHz is discussed in the context of microwave photonics and is experimentally demonstrated to be able to provide a lossless delay up to 1.1 to a 5 ns Gaussian pulse. The proposed device can be designed for different frequency scales with potential for applications across many other areas such as telecommunications, LIDAR, and spectroscopy, serving as a novel building block for creating chip-scale programmable optical signal processors.

We characterize an integrated silicon 4×5 Gb/s OFDM transmitter PIC (2.1×4.8 mm2) with four modulators and an optical Fourier transform. This PIC features a channel spacing of 5 GHz and an 80-GHz free spectral range.

Orthogonal time division multiplexing (OrthTDM) interleaves sinc-shaped pulses to form a high baud-rate signal, with a rectangular spectrum suitable for multiplexing into a Nyquist WDM (N-WDM)-like signal. The problem with generating sinc-shaped pulses is that they theoretically have infinite durations, and even if time bounded for practical implementation, they still require a filter with a long impulse response, hence a large physical size. Previously a method of creating chirped-orthogonal frequency division multiplexing (OFDM) pulses with a chirped arrayed waveguide (AWG) filter, then converting them into interleaved quasi-sinc pulses using dispersive fiber (DF), has been proposed. This produces a signal with a wider spectrum than the equivalent N-WDM signal. We show that a modification to the scheme enables the spectral extent to be reduced for the same data rate. We then analyse the key factors in designing an OrthTDM transmitter, and relate these to the performance of a N-WDM system. We show that the modified transmitter reduces the required guard band between the N-WDM channels. We also simulate a simpler scheme using an unchirped finite-impulse response filter of similar size, which directly creates truncated-sinc pulses without needing a DF. This gives better system performance than either chirped scheme.

Phase-coded radio frequency (RF) pulses are widely adopted for radar systems as an effective signal format to enable high-range resolution. However, generating such signals conventionally requires high-speed electronics and complex RF circuitry that impose burdens on the system cost and power consumption. In particular, modern radar systems desire features such as high frequencies, e.g., in the millimeter-wave region, high compactness, and high system flexibility, which pose great challenges for the conventional all-electronics solutions. In contrast, integrated microwave photonics opens a way to solutions that are able to provide those features simultaneously, together with potential for full integration and low cost fabrication. Here, we present an integrated microwave photonic method of a binary-phase-coded millimeter-wave signal generation. The core device is a silicon microring modulator with a device size of 0.13 mm×0.32 mm and a modulation bandwidth of 23 GHz. Using RF seed frequencies of 17.5 GHz and 20 GHz, respectively, we experimentally demonstrated the generation of binary-phase-coded signals at 35 GHz and 40 GHz using our proposed approach, the performance of which was verified by a pulse compression ratio of 94 and 106, respectively. The result of this work points to the realization of a chip-scale flexible millimeter-wave signal generator.

We propose a novel method to improve a system degraded by a low receiver electrical bandwidth. With optical pre-sampling, 4-dB sensitivity improvement at the 7% hard FEC limit is experimentally demonstrated.

We present an FPGA-based QPSK-encoded 9.375 Gb/s layered/enhanced ACO-OFDM transmitter giving a high spectral efficiency. The measured Q-factor is greater than 13 dB after 20­km standard single-mode fiber transmission.