Search

The inadequacy of conventional control strategies for multi-phase interleaved parallel circuits in terms of adaptive adjustment makes it difficult to meet the power source design requirements for transient electromagnetic detection systems. This paper introduces a novel approach, the variable-domain fuzzy proportional–integral (PI) adaptive control strategy. This strategy dynamically adjusts the fuzzy domain in real time based on the input error magnitude, ensuring improved control effectiveness. By leveraging the benefits of both the functional scaling factor and the fuzzy reasoning scaling factor, we design scaling factors for the input and output domains to enhance control precision. The focus of this study is on a four-phase interleaved parallel converter, emphasizing the design of the variable-domain fuzzy PI control strategy for the voltage outer loop within the traditional dual closed-loop structure. An experimental prototype with a 220 Vac input, 380 V output, and a power rating of 1000 W is constructed. A comparative analysis between fuzzy control and variable-domain fuzzy PI control is conducted in the voltage outer loop of the dual closed-loop control. Results reveal that dual closed-loop control with variable-domain fuzzy PI control for the voltage outer loop significantly enhances system stability. The startup time to reach the steady state is reduced to 0.632 s, with an overshoot of 28.8 V. Transitioning from 25% load to full load takes only 0.096 s, resulting in a minimal drop of 21.4 V and an overshoot of 13.4 V. Similarly, switching from full load to 25% load in 0.167 s exhibits an overshoot of only 19.6 V. The adaptive regulation capability of the converter is markedly improved, showcasing smaller overshoots and higher-level controlling effectiveness. [ABSTRACT FROM AUTHOR]

This paper proposes a nondestructive, separate transmitter-receiver (TX-RX) electromagnetic measurement system for near-surface detection. Different from the traditional dual-coil integrated design, the proposed transient electromagnetic (TEM) system performs shallow subsurface detection using independent TX coil and movable RX coils. This configuration requires a large primary field so that the far-away secondary field is able to generate reliably induced voltages. To achieve this goal, a bipolar current-pulsed power supply (BCPPS) with a late resonant charging strategy is designed to produce a sufficiently large magnetic moment for the exciting coil with low source interference. The magnetic dipole source (MDS) with a large proportion of weight is separated from the field observation device and does not need to be dragged or transported during the detection process. This setup lowers the weight of the scanning device to 3 kg and greatly improves the measurement efficiency. The results of the laboratory test verify the effectiveness of the separate MDS and RX module system. Field experimental detection further demonstrates that the proposed system can realize highly efficient and shallow surface detection within a 200 m range of the MDS device. [ABSTRACT FROM AUTHOR]

Faults in the grounding grid are a hidden danger to the safety of power systems and cause significant economic loss every year. This paper presents a new means to locate faults in grounding grids using the transient electromagnetic imaging method. The method compares the distribution characteristics of the equivalent resistivity of the underground covered by grids for the no-fault case and those with break points. We describe why and how the proposed method can be used for the break-point diagnosis of grounding grids. Simulation was performed using the Ansoft finite-element method package, and a field experiment was conducted to verify the effectiveness of the proposed method. This study provides a practical means for break-point diagnosis with no requirement of power shut down or soil excavation. Moreover, the proposed method does not require the design drawings of grounding grids. [ABSTRACT FROM PUBLISHER]

The rapid detection of urban road disasters has become an urgent problem. The continuous towed geophysical method is an important method for rapid general detection. Ground-penetrating radar and transient electromagnetic have realized continuous towed detection, but the seismic method cannot do it. The reflection seismic method has the advantages of deep detection depth and high resolution. To adapt to the rapid deployment of geophones on urban hardened pavement, a gravity geophone was designed to realize towed acquisition. However, the data acquisition is far from meeting the needs of large area rapid detection on urban roads. In this paper, a continuous towed seismic data collection method is proposed for the first time, that is, the vibration generated by the friction between the geophone base and the ground is used as the seismic source to realize the rapid data acquisition on the urban roads. When the vehicle-mounted seismic equipment is used and the required lateral resolution is 0.5 m, the continuous towed seismic data acquisition efficiency is about 5 km/h. Continuous towed seismic data has a low-resolution and low signal-to-noise ratio, and the real weak reflected signal is drowned by strong energy noise. To solve these problems, this paper proposes a correlation stack method to extract the stack section. When seismic data is collected with the continuous towed seismic equipment, the seismic source signal is not the approximate sharp plus signal, so the resolution of the extracted stack section is still low. Single detection results are difficult to distinguish near-surface structures. The continuous towed seismic acquisition method has a low cost and can realize the rapid repeated detection of the same survey line. The model data and measured data prove that the proposed data acquisition scheme and data processing method have the following advantages: 1) The continuous towed seismic acquisition method can improve the data acquisition efficiency, reduce the cost of data acquisition, and is suitable for large area rapid detection. 2) The correlation stack method can extract reflected signals with real weak energy. 3) Stack processing for multiple detection data can improve the resolution and enhance the energy of real weak signals. The continuous towed seismic data acquisition and the data processing method can realize the rapid inspection and detection of urban roads and has practical engineering application value. • The continuous towed seismic acquisition method can improve the data acquisition efficiency. • The correlation stack method can extract reflected signals with real weak energy. • Stack processing for multiple detection data can enhance the energy of weak signals. • The proposed method is the most efficient and environmentally friendly. [ABSTRACT FROM AUTHOR]

At present, there are no appropriate exploration methods for the shallow water geophysical surveys with depths less than 100 m. In this paper, the detection feasibility of small-loop transient electromagnetic method (TEM) in shallow water was researched from both theoretical and practical application aspects. Firstly, the propagation characteristics of the multi-turn small-loop electromagnetic field and the magnetic dipole in space were compared. Next, a homogeneous half-space shallow water model and a typical low-resistance abnormal body shallow water model were established by using the finite-difference time-domain (FDTD) method. The research results indicate that the strength of the magnetic field intensity is mainly affected by the depth of water, resistivity, and emission current. The response curve of the low-resistance abnormal body at different times indicates double-peak attenuation law. The response of low-resistance abnormal at different depths of shallow water indicates single-peak, double-peak, and peak-to-valley attenuation laws, and the response of low-resistance abnormal at different resistivity of shallow water indicates single-peak and peak-to-valley attenuation laws. The EA parameters were introduced to analyze the effects of different thicknesses and different resistivity on the response of low-resistance abnormal. Finally, the effectiveness and accuracy of the method were verified when comparing the high-density resistivity method with the results of the transient electromagnetic method on water. The research work provides a theoretical reference for the qualitative analysis of the response characteristics and data processing interpretation of the small-loop transient electromagnetic method in shallow water. • A small-loop TEM method suitable for shallow water exploration is proposed. • The EA parameters were redefined. • The detection results of the small-loop TEM in shallow water were verified. [ABSTRACT FROM AUTHOR]