Search

The effects of moisture, oxygen, and acidity upon the aging of Kraft and thermally upgraded ('Insuldur[R]') papers have been studied in detail. The results for Kraft are consistent with the kinetic model and parameters proposed earlier by Emsley et al., and with the principle that moisture promotes acid-hydrolysis by causing carboxylic acids to dissociate. Moisture is released during the aging of Kraft and, hence, its aging is auto-acceleratory. In contrast, Insuldur consumed moisture under the same conditions, aged more slowly, and its aging was less accelerated by added moisture. 2-Furfuraldehyde (2FAL), which is a dehydration product of pentosans and, hence, an index of moisture production, is also released from Kraft during aging, but not from Insuldur. Acids are, however, produced from both types of paper. Theoretical explanations for these findings are proposed, and their practical implications for transformer maintenance are discussed. Index Terms--Acids, aging, hydrolysis, maintenance, oil, oxidation, paper, transformer, 2-Furfuraldehyde, water.

Dynamics of water penetration in mass impregnated cable insulation has been studied. For experimental purposes, artificial damage has been inflicted to a 40-cm-long cable sample and water ingress has been continuously monitored by frequency response measurements. A similar experiment has been conducted on 2.8-m-long cable sample, where both frequency response and time-domain reflectometry (TDR) measurements have been performed. After termination of both experiments, actual moisture content has been measured radially and axially. Based on dielectric measurements, a model of water ingress has been developed and diffusion coefficients have been estimated for mass impregnated cable paper. Index Terms--Dielectric response, Karl Fischer titration, mass impregnated cable, moisture content, oil paper insulation.

Dielectric spectroscopy (dielectric response measurements) has been applied for nondestructive estimation of humidity in oil-paper cable insulation. The experiments have been based upon two field-aged cables, 20 and 50 years old. Paper samples from these cables have been characterized and subjected to environments with different relative humidity. Dielectric loss and capacitance have been measured in a frequency range 1 MHz to 1 kHz and related to the moisture content determined by Karl Fisher titration. A method has been verified where the moisture content is correlated to the minimum value of loss tangent (tan [delta]). A number of field measurements have been performed where the method has been applied to estimate the moisture content in the distribution cables. Index Terms--Dielectric response, Karl Fischer titration, mass impregnated cable, moisture content, oil paper insulation.

Since power transformers are the most important pieces of equipment in electricity transmission and distribution systems, special attention must be paid to their maintenance in order to keep them in good condition for a long time. This paper reviews the main steps in the process of diagnosing the health of power transformer insulation, which involves the science of analysing the gases dissolved in power transformer oil for effective identification of faults. An accurate diagnosis of incipient faults is favourable to sustainable development and necessary to maintain a reliable supply of electricity. The methods presented for fault diagnosis in mineral-oil-immersed power transformers are divided into analytical and graphical methods and have been found to be simple, economical and effective. After describing the methods, both their strengths and weaknesses were identified, and over the years, the methods were complemented to provide highly accurate information, validated by field inspections. This paper focuses on practical information and applications to manage maintenance based on accurate and up-to-date data. The contents of this paper will be of particular use to engineers who manufacture, monitor and/or use high-power transformers in the energy sector, as well as to undergraduate, master's and PhD students interested in such applications. [ABSTRACT FROM AUTHOR]

Dielectric testing techniques, in both time and frequency domains, are currently widely used by power utilities for assessment of the condition of transformer oil-paper insulation systems. However, it has been reported that results of these tests are highly influenced by the operating temperature during measurements. The distribution, migration and equilibrium of moisture between oil and paper in a complicated insulation system is highly temperature dependent. It requires adequate experience and proper understanding to interpret the dielectric response results in the presence of temperature variations and thermal instability. Proper analysis of the dielectric test result is only possible with an understanding of the physical behavior of the insulation system in response to temperature. A circuit model, which describes the dielectric behavior of the transformers main insulation system, has been investigated in this paper. The values of the parameters of the model have been identified from the dielectric tests. A correlation has been observed between the operating temperature and the equivalent model parameters that can be used as additional information for better interpretation of the dielectric test results. This paper thus reports a detailed study on the effects of temperature on dielectric measurements of a transformer under controlled laboratory conditions. Some results of practical on-site testing are also presented to demonstrate the possibility of errors that may be introduced in dielectric test results analysis unless temperature effects are taken into consideration. [ABSTRACT FROM AUTHOR]

Abstract: HV transformers are taken into account as the heart of the power distribution system. The on-line monitoring based on the oil analysis offers a rapid diagnostic technique to detect the probable faults. In fact, the transformer malfunctions can be detected using UV laser spectroscopic methods. Here, a novel technique is presented based on simultaneous laser induced fluorescence (LIF) and laser induced breakdown (LIB) spectroscopy for hyper sensitive identification of the oil degradation. Oil is mainly degraded due to the internal transformer faults such as overheating and partial discharge. The spectroscopic characteristics of oil in paper substrate were obtained due to ArF laser irradiation. It was shown that the amplitude of fluorescence signal increases when the oil suffers aging and degradation. A couple of additional characteristic carbon and Hα emissions appear in the corresponding breakdown spectra too. [Copyright &y& Elsevier]

This article explores the impact of electric vehicle (EV) charging on power systems and emphasizes the importance of careful analysis and planning. It discusses various topics related to EV charging, including EV hosting capacity, optimal placement of EVs and charging stations, technical impacts of Vehicle-to-Grid (V2G) technology, shared vehicle rental, decentralised collaboration frameworks, intelligent energy management schemes, EV demand response, and optimal sizing and siting of public EV charging stations. The article provides valuable insights and solutions for utilities, academia, and policymakers to address the challenges and opportunities associated with EV charging. Additionally, the article introduces a new approach for determining the limits of transformers and overhead lines in relation to EV charging, using Monte Carlo simulations and proposing new parameters for evaluating maximum demands. The authors stress the need for further analysis and attention to the impact of EVs on power systems. [Extracted from the article]

The ongoing electrification of the transport sector is expected to cause an increase in electricity demand and, therefore, trigger significant network investments to accommodate it. This paper focuses on investment decision-making for electricity distribution grids and specifically on the strategic and incremental investment network planning approaches. In particular, the former involves network planning with the consideration of a long-term multi-stage study horizon, as opposed to a shorter–term view of the future that applies to the latter case. An investment analysis that is carried out underlines the economic savings generated from adopting a strategic investment perspective over an incremental one. These economic savings are achieved from the fact that the associated fixed investment costs are incurred only once in the horizon under strategic planning. On the other hand, incremental planning involves a series of network reinforcement decisions, thereby incurring the fixed cost multiple times. In addition, sensitivity analyses that are carried out capture the effect of key parameters, such as investment cost, discount rate and investment delay, on the generated economic savings. [ABSTRACT FROM AUTHOR]

With the growing movement of using direct current (DC) load demands, as well as DC distribution generations (DGs), the distribution system has undergone significant changes on the production and demand side. Due to alternating current (AC) and DC generators and load demands, it is not costeffective to continue in the AC distribution system. Therefore, AC/DC hybrid distribution system planning is economical despite various demands and generations. On the other hand, uncertainty in load demand and output power of DGs cause the possible behavior of the distribution system. This behavior leads to risk in the distribution system. In this paper, the AC/DC distribution system planning is discussed by considering the risk. The planning problem in the matrix laboratory and general algebraic modeling system (MATLAB/GAMS) hybrid space has been formulated and solved. Using the K-means algorithm, the uncertainty related to renewable DG output power and load demand has been modeled. To verify the proposed method, it was implemented in a sample distribution system. [ABSTRACT FROM AUTHOR]

During the energy transition, new types of electrical equipment, especially power electronic devices, are proposed to increase the flexibility of electricity distribution grids. One type is the solid-state transformer (SST), which offers excellent possibilities to improve the voltage quality in electricity distribution grids and integrate hybrid AC/DC grids. This paper compares SST to conventional copper-based power transformers (CPT) with and without an on-load tap changer (OLTC) and with additional downstream converters. For this purpose, a corresponding electricity distribution grid is set up in the power system analysis tool DIgSILENT PowerFactory 2022. A DC generator like a photovoltaic system, a DC load like an electric vehicle fast charging station, and an AC load are connected. Based on load flow simulations, the four power transformers are compared concerning voltage stability during a generator-based and a load-based scenario. The results of load flow simulations show that SSTs are most valuable when additional generators and loads are to be connected to the infrastructure, which would overload the existing grid equipment. The efficiency of using SSTs also depends on the parameters of the electrical grid, especially the lengths of the low-voltage (LV) lines. In addition, a flowchart-based decision process is proposed to support the decision-making process for the appropriate power transformer from an electrical perspective. Beyond these electrical properties, an evaluation matrix lists other relevant criteria like characteristics of the installation site, noise level, expected lifetime, and economic criteria that must be considered. [ABSTRACT FROM AUTHOR]

Many emerging applications, such as factory automation, electric power distribution, and intelligent transportation systems, require multicast Ultra-Reliable Low-Latency Communications (mURLLC). Since 3GPP Release 17, 5G systems natively support multicast functionality, including multicast Hybrid Automatic Repeat Request and various feedback schemes. Although these features can be promising for mURLLC, the specifications and existing studies fall short in offering guidance on their efficient usage. This paper presents the first comprehensive system-level evaluation of mURLLC, leveraging insights from 3GPP specifications. It points out (i) how mURLLC differs from traditional multicast broadband wireless communications, and (ii) which approaches to provide mURLLC require changing the paradigm compared with the existing solutions. Finally, the paper provides recommendations on how to satisfy strict mURLLC requirements efficiently, i.e., with low channel resource consumption, which increases the capacity of 5G systems for mURLLC. Simulation results show that proper configuration of multicast mechanisms and the corresponding algorithms for mURLLC traffic can reduce resource consumption up to three times compared to the baseline solutions proposed for broadband multicast traffic, which significantly increases the system capacity. [ABSTRACT FROM AUTHOR]

Line loss refers to the electrical energy that is dissipated as heat during the transmission and distribution of electricity through power lines. However, unusual causes, such as grid topology mismatch and communication failure, can cause abnormal line loss. Efficient abnormal line loss detection contributes not only to minimizing energy wastage and reducing carbon emissions but also to maintaining the stability and reliability of the entire distribution network. In actual situations, the cause of abnormal line loss is not labeled due to the expensive labor cost. This paper proposes a hierarchical abnormal line loss identification and category classification model, considering the unlabeled and unbalanced sample problem. First, an abnormal line loss identification model-based random forest is established to detect whether the line loss is abnormal. Then, an abnormal line loss category classification model is developed with semi-supervised learning for line loss abnormal category classification, considering the unlabeled samples. The real dataset in China is utilized to validate the performance of the proposed model. Its reliability implies the potential to be applied to real-world scenarios to improve the management level and safety of the power grid. [ABSTRACT FROM AUTHOR]

The aim of this study was to study the security problems faced by an Radio Frequency Identification (RFID) system in the whole process management of intelligent power distribution system equipment. Based on information security risks, the defects are analyzed, and how to protect distributed energy stations from information security threats in the energy Internet environment is discussed. This paper analyzes the new business communication requirements of distribution communication network and the security risks. The results are as follows: in the classification accuracy experiment, the accuracy of all kinds of classification is obtained through three algorithms [DAG-SVM based on minimum coupling degree, DAG-SVM based on maximum separability, and double-decision hyperplane (DDH)]. Among them, the accuracy of the optimized DDH algorithm in this paper is 98.65%, which is the highest of the three, and the time is the shortest, saving about 40%. A security protocol is proposed which has good protection against several attacks. Deep neural network was used to mine the power terminal attack by means of feature engineering and data enhancement, and the network-level security monitoring of power terminals is realized. The feasibility of the proposed method is verified by building a physical simulation platform, and the experimental results show that the proposed strategy can improve the security of power terminals. [ABSTRACT FROM AUTHOR]

Synchronous generator-based power stations, with their inherent inertia, can maintain frequency stability during sudden load switching, while distributed generating station-driven microgrids suffer from a lack of natural inertia. Cascaded power, voltage, and current controllers are a widespread control strategy used to regulate the power output of distributed generating stations to maintain frequency and voltage within stable limits. Virtual synchronous generator (VSG) control for the power controller is used as a potential solution to emulate inertia. To derive maximum benefit from VSG, proper tuning of its multiple parameters is required. In this direction, earlier works proposed the equivalence between the droop and VSG schemes, which suggested that the droop coefficient value could be directly used in the design of VSG. As an improvement to these conventional works, the proposed work in this paper identifies that VSG delivers a better response when an equalizing constant is used to adjust the droop coefficient value than using it directly. This paper proposes implementing the VSG with an equalizing constant as a new design parameter. A description of designing the parameters of this improved VSG considering the equalizing constant is also discussed in this paper. The performance of the conventional VSG and the proposed improved VSG are compared. From the results, it is observed that, at load switching, the output frequency of the proposed method in all test cases has settled at less than 3 s, while the conventional method took a maximum of 6 s in critical cases. Further, the output frequency's maximum peak with the proposed method is 3 Hz less than the conventional method. These, along with other metrics, validate the importance of the proposed improved VSG-based control scheme for the enhancement of transient responses in microgrids. [ABSTRACT FROM AUTHOR]

In recent years, Microgrids in integration with Distributed Energy Resources (DERs) are playing as one of the key models for resolving the current energy problem by offering sustainable and clean electricity. Selecting the best DER cost and corresponding energy storage size is essential for the reliable, cost-effective, and efficient operation of the electric power system. In this paper, the real-time load data of Bengaluru city (Karnataka, India) for different seasons is taken for optimization of a grid-connected DERs-based Microgrid system. This paper presents an optimal sizing of the battery, minimum operating cost and, reduction in battery charging cost to meet the overall load demand. The optimization and analysis are done using meta-heuristic, Artificial Intelligence (AI), and Ensemble Learning-based techniques such as Particle Swarm Optimization (PSO), Artificial Neural Network (ANN), and Random Forest (RF) model for different seasons i.e., winter, spring & autumn, summer and monsoon considering three different cases. The outcome shows that the ensemble learning-based Random Forest (RF) model gives maximum savings as compared to other optimization techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a new comprehensive load restoration (LR) method for electrical distribution networks. Since two main technologies of switching equipment are there in the modern distribution networks, namely manual switches (MSs) and remote‐controlled switches (RCSs), this article has benefited from this concept effectively. A two‐stage algorithm that provides the system operators with the ability to recover part of the loads in the shortest possible time by RCSs is proposed. After this step, the remaining loads will be restored by a combination of MSs and RCSs. The other strength of this algorithm is to provide accurate and practical solutions so that the sequence of switching actions is clearly defined. Also, using an innovative index called expected weighted energy not supplied as the objective function of the main problem will ensure the operators recover the maximum amount of load in the shortest time possible. This novel method was applied on a sample standard IEEE distribution test network. The simulation results proved the effectiveness of this proposed method. [ABSTRACT FROM AUTHOR]

To calculate the losses of distribution feeders, this paper uses an iterative method that is limited to restricted measurements. The approach presented in this paper uses bill data in addition to output information from a very small number of real-time measurements located on the secondary side of distribution transformers. This method attempts to estimate the load of distribution transformers injected into LV feeders. Energy losses for LV feeders are evaluated by first estimating the power and periodic energy injected to each of the LV feeders and then subtracting the total consumption bills from these estimated values. By using this method, the amount of energy loss is estimated. In this article, a new method called iterative power factor adjustment method is considered as a potential method for estimating losses. The power factor can be increased by repeatedly using evolutionary algorithms and including capacitors in the system. In order to reduce system losses and increase network effectiveness. In this paper, a new method for examining and evaluating Non-Technical Losses (NTL) is proposed. This method considers load estimation and limited measurement to place high priority feeders. [ABSTRACT FROM AUTHOR]

Transmission lines, the core part of the transmission and distribution system in the smart grid, require effective, efficient, and reliable protective measures against faults to avoid severe damage to physical infrastructure and financial losses. Due to their growing popularity, machine learning models are used in fault detection and classification, whose performances can be severely affected by cyber‐attacks due to their data dependency, posing a critical concern. Hence, this paper introduces false data injection attacks to address the vulnerability of machine learning‐based fault detectors and classifiers. A comparative study of 9 detection models and 6 classification models under normal conditions and during a combination of two models of false data injection attacks is presented to evaluate the severity of cyber‐attacks. Experimental results show that highly accurate models in normal conditions are more susceptible to cyber‐attacks, with up to 69% and 28% degradations in accuracy for fault detectors and classifiers, respectively. Furthermore, the detection models are found to be more vulnerable to cyber‐attacks than the classification models. With no robust detectors and classifiers being found, this work addresses the importance of developing attack‐resilient fault detection and classification schemes considering their academic and industrial significance. [ABSTRACT FROM AUTHOR]

This paper explores the complex interactions that exist between national ancillary service markets and local flexibility in Türkiye's changing power landscape. The significance of grid flexibility is escalating, especially with the country's transition from a predictable energy generation model to one predominantly fueled by intermittent renewable sources, coupled with the imminent integration of nuclear power. Ancillary services, encompassing functions such as frequency control, voltage regulation, and system restart, play a pivotal role in upholding grid stability. The study particularly underscores the significance of frequencyrelated ancillary services in preserving grid equilibrium. Moreover, it emphasizes how important electricity distribution businesses are as major players in improving grid stability. These businesses can actively participate in ancillary service markets and support grid stability by utilizing local flexibility solutions like distributed generation, energy storage, and demand response. This benefits the grid as well as consumers. The central objective of the study is to explore the synergies between local flexibility solutions and national ancillary markets. A case study is employed to evaluate the potential benefits and profitability associated with the integration of these components for an electrical distribution company. A combination solution utilizing solar panels, battery storage systems, electric vehicle charging infrastructure, and a natural gas turbine within the gearbox company's network is the subject of a case study that is presented. The concept of local flexibility and its mutually beneficial relationship with the national auxiliary service markets are also clarified in the study. The findings demonstrate the potential profitability and advantages of battery storage for the national energy grid. A substantial increase in prices for Frequency Restoration Reserve is imperative to render the natural gas turbine economically sustainable. [ABSTRACT FROM AUTHOR]

This paper investigates outage management in electricity distribution networks through the application of artificial intelligence techniques. The core of the system utilizes a diverse dataset compiled from outage management system records, weather forecasts, and geographical data to predict potential electricity outages. The data is rigorously analyzed to determine correlations between various weather conditions and outage occurrences, with particular emphasis on the impact of wind speed and storm conditions. The predictive model, a cornerstone of this research, employs a hybrid artificial intelligence algorithm that integrates outputs from convolutional neural networks, recursive neural networks, and extreme gradient boosting. The predictions are further refined using a feedforward neural network and distributed to specific districts based on historical data trends. Comparative analysis against a naive model based on historical averages highlights the superior performance of the hybrid model, showcasing its reduced error rates and enhanced predictive accuracy. This decision support system not only provides reliable outage predictions but also facilitates more effective management strategies, thus improving operational efficiencies and customer service in electricity distribution. The findings underscore the potential of advanced analytics in transforming utility management and pave the way for further innovations in smart grid technology and outage prevention strategies. [ABSTRACT FROM AUTHOR]

The significant growth in demand for electricity has led to increasing congestion on distribution networks. The challenge is twofold: it is needed to expand and modernize our grid to meet this increased demand but also to implement smart grid technologies to improve the efficiency and reliability of electricity distribution. In order to mitigate these congestions, novel approaches by using flexibility sources such as battery energy storage can be used. This involves the use of battery storage systems to absorb excess energy at times of low demand and release it at peak times, effectively balancing the load and reducing the stress on the grid. In this paper, two optimal power flow formulations are discussed: the branch flow model (non-convex) and the relaxed bus injection model (convex). These formulations determine the optimal operation of the flexibility sources, i.e., battery energy storage, with the objective of minimizing power losses while avoiding congestions. Furthermore, a comparison of the performance of these two formulations is performed, analyzing the objective function results and the flexibility operation. For this purpose, a real Spanish distribution network with its corresponding load data for seven days has been used. [ABSTRACT FROM AUTHOR]

The expansion of distributed renewable resources, together with increased demand from the electrification of transport and heating sectors, impacts distribution networks significantly. Additionally, the emergence of non-programmable and intermittent generators is set to diminish the dominance of traditional rotating and programmable generation, thereby affecting the overall stability of the system. Nevertheless, the flexibility offered by distributed resources has the potential to alleviate the necessity for network reinforcement and contribute to system stability at competitive costs. Local flexibility procurement should be rooted in local markets, serving as mechanisms to address distribution congestion and coordinate the provision of flexibility for transmission network services. The multitude of existing systems and the interdependence of flexibility services have given rise to diverse solutions, still undergoing experimentation in various countries. This paper aims to scrutinize key projects that have established local flexibility markets, delineating their fundamental characteristics, the most common solutions, identifying prevalent barriers and suggesting potential future improvements. The investigation focuses on the most uncertain aspects of local markets: possible TSO-DSO coordination schemes, the time horizon for the acquisition of services and the baseline definition methodologies. [ABSTRACT FROM AUTHOR]

It is widely recognised that improving the visibility and controllability of distributed energy resources (DERs) within electricity distribution networks will have significant benefits, particularly for the management of low-voltage (LV) and medium-voltage (MV) networks. Much work within the electricity distribution industry is currently focused on improving the visibility of DERs on LV networks. From a control-theoretic perspective, this enables closing the loop between the DER and the control room and enables a shift towards utilising data-driven model-based control strategies for DERs. The result is a system-wide performance that is closer to the theoretical optimal. In the Australian context, several jurisdictions are trialling techniques such as dynamic operating envelopes to enhance DER hosting capacity, using IEEE 2030.5-based architectures, with the implementation of distributed energy resource management (DERMS) systems at the enterprise level still quite limited. While there is significant activity focused on DER behaviour and control techniques by way of inverter grid codes and standards, the core issue of interoperability with distribution management systems (DMSs), market operators or participants, electric vehicles (EVs) or other DERs is still a work in progress. Importantly, this is also an impediment to realising distributed architectures for DER control in the grid. The unique characteristics of Australian distribution networks highlights several challenging problems for DER control and management. The objective of this paper is to provide a broad overview of DER control and management strategies in the Australian context, with an application focus on DER control in distribution network management. [ABSTRACT FROM AUTHOR]

The latest of a series of classified lists of power system relaying references, begun in 1927, is presented. This bibliography is in continuation to the bibliographies of relay literature, which were published previously and are contained in the following volumes of the IEEE Transactions: [ABSTRACT FROM AUTHOR]

Expressions have been developed to describe the influence of recirculation on the energy distribution on pulp in refiners. It was shown that for constant pulp flow to downstream operations, the average energy expenditure on pulp does not change with recirculation, but the energy expended on components of the pulp flow varies widely. In the case of reduced fiber flow, the recirculation to maintain constant flow and the power to maintain constant average specific energy produces a change in both the energy distribution on pulp and refining intensity. The implications of these findings to pulp refining are discussed in this work. [ABSTRACT FROM AUTHOR]

The latest of a series of classified lists of power system relaying references, begun in 1927, is presented. This bibliography is in continuation to the bibliographies of relay literature, which were published previously and are contained in the following volumes of the IEEE Transactions. [ABSTRACT FROM AUTHOR]

We report on the potential of today's LED technologies to approximate Spectral Power Distributions (SPDs) aimed at optimizing specific performance goals. We compare numerically optimal SPDs to actual SPDs produced by a 16-channel LED light source, aiming at optimizing performance for six different applications. These theoretical and practical limits of the potential of current LED technologies can serve as guidelines for the design of future LED sources for different applications. [ABSTRACT FROM AUTHOR]

A terminal for remote control of charging stations for electric vehicles (EV) powered by renewable energy has been presented in this paper. This terminal enables remote control of EV chargers, smart batteries, smart electricity meters, fiscal cash registers (FCR), as well as remote control of renewable energy sources and other devices within the station. This terminal also makes charging stations more accessible to electric vehicles users, to electricity distribution companies, to electricity suppliers, to tax administrations, and finally to users and owners of charging stations. Therefore, communication and control with all these devices and systems is integrated in one device. Realization of hardware and software of such a terminal has also been described in this paper. The net result of development and commercialization of terminals would encourage an increase in the use of electric vehicles powered by energy from renewable sources, which would cause a decrease in the level of air pollution and all negative effects it causes in the future. Different categories of this device are considered. Moreover, although it is a device with embedded software, a very advanced method was used, that is, a model-driven development method, which enables fast and more efficient development and maintenance of the device. The results of the application of this method to the terminal for remote control of fiscal cash registers are provided. They were compared with the results of the development of the terminal for remote control of smart meters without applying this method. A simulation of the development of the terminal for remote control of the station is also provided. The presented method can be used in the future for faster and better-quality development of embedded software. [ABSTRACT FROM AUTHOR]

The ESCOM (Electricity Supply Corporation of Malawi) currently faces difficulties in monitoring and controlling critical parameters, such as electricity generation, transmission, and distribution in real-time. Inefficient energy management, lack of fault detection mechanisms, manual interventions, and limited data-driven decision-making capabilities are hindering ESCOM's ability to deliver reliable and efficient electricity services to the people of Malawi. The main objective of this work is to address the pressing challenges faced by ESCOM (Electricity Supply Corporation of Malawi) in effectively managing and optimizing electricity distribution within their infrastructure. This paper introduces an IoT-based industrial management system designed to tackle these challenges and enhance ESCOM's operational efficiency, energy management, and overall performance. [ABSTRACT FROM AUTHOR]

In this paper, postmortem aging investigations on insulation material of power transformers are presented. A methodology for taking paper samples in a systematical manner and a scheme for calculating an average degree of polymerization (DP) for the entire transformer out of the DP values of the individual paper samples will be shown. The typical DP profile in the axial direction of transformer coils will be explained using calculated distribution of losses within the coils of a 740-MVA generator stepup transformer. Further, correlations between the furan (2-FAL) concentration in the oil and the average DP of the investigated German GSU transformers and grid transformers are derived and compared with existing correlations. [ABSTRACT FROM PUBLISHER]

This paper discusses a recent event in the western American power system when a forced oscillation was observed at a frequency that was close to a well-known 0.38-Hz inter-area electromechanical mode frequency of the western system. The event motivates a systematic investigation in this paper on the possibility of resonant interactions between forced oscillations and electromechanical inter-area oscillatory modes in power systems. When the natural oscillatory mode of a power system is poorly damped, and the forced oscillation occurs at a frequency close to system mode frequency at critical locations for the mode, resonance is observed in simulation test cases of the paper. It is shown that the MW oscillations on tie-lines can be as high as 477 MW from a 10-MW forced oscillation in Kundur test system because of resonance. This paper discusses the underlying system conditions and effects as related to resonance in power systems caused by forced oscillations and discusses ways to detect such scenarios using synchrophasors. Simulated data from Kundur two-area test power system as well as measurement data from western American power system are used to study the effect of forced oscillations in power systems. [ABSTRACT FROM AUTHOR]

Clustering-based reactive voltage partitioning is successful in reducing grid cascading faults, by using clustering methods to categorize different power-consuming entities in the power grid into distinct regions. In reality, each power-consuming entity has different electrical characteristics. Additionally, due to the irregular and uneven distribution of the population, the distribution of electricity consumption is also irregular and uneven. However, the existing method neglects the electrical difference among each entity and the irregular and uneven density distribution of electricity consumption, resulting in poor accuracy and adaptability of these methods. To address these problems, an enhanced density peak model-based power grid reactive voltage partitioning method is proposed in this paper, called EDPVP. First, the power grid is modeled as a weighted reactive network to consider entity electrical differences. Second, the novel local density and density following distance are designed to enhance the density peak model to address the problem that the traditional density peak model cannot adapt to weighted networks. Finally, the enhanced density peak model is further equipped with an optimized cluster centers selection strategy and an updated remaining node assignment strategy, to better identify irregular and uneven density distribution of electricity consumption, and to achieve fast and accurate reactive voltage partition. Experiments on two real power grids demonstrate the effectiveness of the EDPVP. [ABSTRACT FROM AUTHOR]

With the development of EVs (Electric Vehicles) and the rapidly developing policies on low carbon and environmental protection, electric power systems and natural gas systems become increasingly larger. Under these circumstances, the V2G (Vehicle-to-grid) and the coordinated operation of an integrated electricity–gas distribution system (IEGDS), considering CO2 emissions, can play a part together in the process of energy conservation. Firstly, the V2G model is discussed; this paper presents the cost differences between out-of-order and order for the car. Secondly, the IEGDS model presents coupling constraints of gas turbines and power-to-gas. Lastly, carbon emission is considered in this paper; a carbon capture plant (CCP) captures the CO2 burning by fossil fuel in the power generation process and stores it in a carbon storage tank. This paper also considers trading with the carbon market via a carbon storage warehouse. With the cooperation of various components, a comprehensive model considers the use of V2G to store power in the IEGDS system, with consideration of the carbon trade. Numerical experiments validate the effectiveness of the combination between V2G and IEGDS, considering carbon emissions and carbon trading. [ABSTRACT FROM AUTHOR]

Phase unbalance is a common issue encountered in LV electricity distribution networks, caused by uneven allocation of single-phase loads among phases. This paper analyses a part of a real LV distribution network, situated in Bosnia and Herzegovina. The impact of single-phase customers and single-phase charging of electric vehicles was analysed. To reduce unbalance and improve the voltage profiles, Phase Balance Optimization in DIgSILENT PowerFactory software was performed in six scenarios with different customer and electric vehicle unbalance. The goal was to find a method with the least number of changes in the customer and electric vehicle phase connection that fits within defined limits of voltage variations and voltage unbalance of a European norm for power quality (EN 50160). Results showed that all analysed scenarios were improved, with reference to voltage variation and voltage unbalance values, and were found acceptable by the limits from standard EN 50160. [ABSTRACT FROM AUTHOR]

The importance of service quality to improve customer's satisfaction is well known to company managers; however, electricity distribution companies still tend to measure customer's satisfaction by the technical performance qualified by an uninterrupted supply of energy. For this reason, the aim of this paper is to study and compile what the literature suggests regarding customer's satisfaction in electricity distribution services and other related public services, in order to propose a conceptual model to measure customer's satisfaction based on a set of performance indicators. The model is based on a content analysis of a paper set sampled from systematic literature reviews. Techniques for data gathering, organisation and representation are based on conceptual maps and data analysis provided by NVivo content analysis platform. The findings presented in this paper cover (i) a set of 20 indicators, outlining all different terminologies found in the literature to express themselves; (ii) a description of a chosen set of indicators using the record sheet proposed by Neely, Gregory, and Platts (1997); (iii) a conceptual model presenting necessary aspects to measure the customer's satisfaction of residential electrical energy distribution service. [ABSTRACT FROM AUTHOR]

This study explores the potential of Istisna'-Ijarah Sukuk in Kano State Nigeria. The State government had identified a multiplier adverse effect of the lingering problem of inadequate electricity supply in the state. As such, the State embarked on building an Independent Power Plant (IPP) to alleviate the power shortage. Using its Internally Generated Revenues (IGR), the State government resolved to finance the construction of Kano IPP worth N14.2billion. Instead, this research argues to make a case for Istisna-Ijarah Sukuk as alternative source of funding the project in the State. Using interview, the paper collects a cross-sectional data from the State and its 44 Local Governments Authority (LGAs), the Regulators (Securities and Exchange Commission - (SEC), the Private Sector (Mergers Association), the Kano Electricity Distribution Company (KEDCO) and investors. 20 respondents were purposively selected from the total 60 sample size. Thematic analysis with coding was employed to analyze the data. Other relevant online sources were used as secondary data. The paper finds Istisna'-Ijarah Sukuk suitable for financing IPP and other relevant infrastructures in the State. Thus, it recommends that, the State should draw a good lesson from successful Osun State Sukuk and use Istisna'-Ijarah Sukuk against using IGR or public borrowing. Policy and regulatory framework are needed and awareness for private sectors and investors for its huge potential. [ABSTRACT FROM AUTHOR]

Energy storage systems (ESS) are seeing rapid market growth due to the changing worldwide landscape of electricity distribution and consumption. An ESS must possess the capability to oversee the functioning of the system's modules under abnormal circumstances, while also having the ability to supervise, manage, and optimize the performance of one or more battery modules. At present, the condition of batteries is assessed based on two factors: the level of charge (SOC) and the overall condition (SOH). By using these two characteristics, it becomes feasible to compute the anticipated battery lifespan and evaluate a battery's efficiency. The assessment of SOH is a crucial determinant in guaranteeing the effectiveness, dependability, and security of batteries in electric vehicles (EVs). Nevertheless, the safety issues resulting from the imprecise estimation and forecasting of battery health status have garnered significant attention in academic circles. This study presents a comprehensive evaluation of several SOH monitoring techniques. In order to achieve this objective, various scientific and technical literatures are examined and the corresponding methodologies are categorized into distinct groupings. The groupings are categorized based on the manner in which the procedure is executed: methods and techniques used in experiments and models. This paper provides a comprehensive overview of the benefits and drawbacks of several SOH assessment and prediction techniques, along with the associated obstacles in SOH estimation. [ABSTRACT FROM AUTHOR]

Assessments of the hosting capacity of electricity distribution networks are of paramount importance, as they facilitate the seamless integration of rooftop photovoltaic systems into the grid, accelerating the transition towards a more carbon neutral and sustainable system. This paper employs a deep reinforcement learning-based approach to evaluate the real-time hosting capacity of low voltage distribution networks in a model-free manner. The proposed approach only requires real-time customer voltage data and solar irradiation data to provide a fast and accurate estimate of real-time hosting capacity at each customer connection point. This study addresses the imperative for accurate electrical models, which are frequently unavailable, in evaluating the hosting capacity of electricity distribution networks. To meet this challenge, the proposed approach utilizes a deep neural network-based, data-driven model of a low-voltage electricity distribution network. This proposed methodology incorporates model-free elements, enhancing its adaptability and robustness. In addition, a comparative analysis between model-based and model-free hosting capacity assessment methods is presented, highlighting their respective strengths and weaknesses. The utilization of the proposed hosting capacity estimation model enables distribution network service providers to make well-informed decisions regarding grid planning, leading to cost minimization. [ABSTRACT FROM AUTHOR]

With the continuous development of renewable energy technologies, both domestically and internationally, the focus of energy research has gradually shifted towards renewable energy directions such as distributed photovoltaics and wind power. The penetration rate of renewable energy generation is constantly increasing, at the same time, the elements in the grid are becoming increasingly complex, and large-scale energy storage, as well as a variety of electricity loads such as electric vehicle charging piles and data centers are gradually appearing. Therefore, traditional distribution methods of the power grid are difficult to ensure the stable operation of the power system and cannot achieve efficient integration of renewable energy. Consequently, some scholars have proposed the concept of an energy internet. Compared to traditional power grids, the energy internet employs more comprehensive power electronics and communication technologies, enabling the interconnection of various new and traditional energy sources, and effectively integrating renewable energy. As the core device in the energy internet, the energy router plays a role in energy transformation and distribution, facilitating multi-information interconnection and multi-energy exchange within the energy internet. At the level of distribution network, the energy router can realize the efficient access of various forms of energy and the flexible control and management, which is of great significance for the optimal operation of distribution network. Against this backdrop, this paper reviews the development and current research status of energy routers, systematically analyzes the typical topologies and related control technologies of multi-port energy routers and summarizes and forecasts key issues and future development trends, aiming to provide thoughts and reference for subsequent related research. [ABSTRACT FROM AUTHOR]

Introduction: In order to promote the consumption of renewable energy, reduce carbon emissions, and take into account the uncertainty of renewable energy output and load fluctuations in the new power system that can affect the normal operation of market mechanism, a two-stage low-carbon optimization scheduling method for power system that considers demand response under multiple uncertainties is proposed in this paper. Methods: Uncertain scene sets are generated through Latin hypercube sampling and heuristic synchronous backpropagation method is used to reduce scenes to obtain typical scenes and their probabilities. Then, a one-stage optimization model is established with the goal of maximizing energy efficiency and corresponding demand response strategies are obtained. Green certificate carbon trading joint mechanism model consisting of tiered green certificate trading and time-sharing tiered carbon trading are established, and the output of two-stage units are optimized with the goal of minimizing comprehensive operating costs. Result: The simulation results show that the carbon emissions are decreased by 251.57 tons, the consumption rate of renewable energy is increased by 8.64%, and the total costs are decreased by 124.0612 million yuan. Discussion: From this, it can be seen that the dual layer low-carbon optimization scheduling strategy for power system considering demand response under multiple uncertainties can effectively reduce the operating costs and carbon emissions of the system, while balancing the economic and environmental aspects of power system operation. [ABSTRACT FROM AUTHOR]

In this paper, the problem of sizing and placement of constant and switching capacitors in electrical distribution systems is modelled considering the load uncertainty. This model is formulated as a multicriteria mathematical problem. The risk of voltage violation is calculated, and the stability index is modelled using fuzzy logic and fuzzy equations. The instability risk is introduced as the deviation of our fuzzy-based stability index with respect to the stability margin. The capacitor placement objectives in our paper include: (i) minimizing investment and installation costs as well as loss cost; (ii) reducing the risk of voltage violation; and (iii) reducing the instability risk. The proposed mathematical model is solved using a multi-objective version of a genetic algorithm. The model is implemented on a distribution network, and the results of the experiment are discussed. The impacts of constant and switching capacitors are assessed separately and concurrently. Moreover, the impact of uncertainty on the multi-objectives is determined based on a sensitivity analysis. It is demonstrated that the more the uncertainty is, the higher the system cost, the voltage risk and the instability risk are. [ABSTRACT FROM AUTHOR]