Search

In this paper, the characteristics of ripple current of a multimegawatt drive system fed by a pulse-width modulation (PWM) inverter are investigated. Based on the investigation, a novel PWM scheme is devised to reduce the switching loss of the inverter under an identical amount of torque ripple of a motor. The proposed PWM is composed of two parts. The first is minimum torque ripple PWM (MTRPWM), which is optimized in terms of the minimum torque ripple in high modulation index (MI). The second determines the minimum switching frequency while holding the average torque ripple less than the allowable value under various operating conditions. It is termed reduced switching frequency PWM (RSFPWM). Consequently, by simply changing the PWM method from conventional fixed switching frequency continuous PWM to the proposed PWM, MTRPWM and RSFPWM, simulation results show that the switching loss of the inverter driving a 3.5 MW induction motor is reduced to 51.6% while keeping the torque ripple in the allowable boundary, where MI is 1.12. This approach is applied to small-scale experimental sets consisting of an interior permanent magnet synchronous machine (IPMSM) motor-generator set, and an induction machine MG set in an effort to verify the validity and feasibility of the proposed method. Based on these experimental results, the cost indexes of the IPMSM and the induction machine, as defined in this paper, decrease by up to 66% and 77%, respectively, when the proposed method is applied when MI is 1.12 compared with the outcome with the conventional PWM. [ABSTRACT FROM AUTHOR]

In signal injection sensorless drives, the injection voltage cannot be reduced under a certain value. The lower limit of the injection voltage is mainly enforced by the inverter nonlinearity that causes distortion of the injection voltage and degradation of the position estimation performance. After analyzing the inverter nonlinearity during the voltage injection, it is revealed that parasitic capacitances of insulated-gate bipolar transistors have positive effects on inverter output linearity and sensorless control. Based on this analysis, this paper proposes a method to reduce the injection voltage by connecting additional capacitors to the output terminals of the inverter. Simulation and experimental results are provided to verify the effectiveness of the proposed idea. In the experiments, using the capacitor-integrated inverter, it is shown that the injection voltage can be reduced by more than half without degrading the position estimation performance. [ABSTRACT FROM AUTHOR]

This paper addresses the inverter nonlinearity of a three-level T-type inverter. The main causes of the nonlinearity are pulse shaping, pulse skipping due to narrow pulses for the dead time, and voltage drop of the switching devices. Although the same causes have existed in two-level inverters, the pulse skipping phenomenon and results are quite different in the case of the three-level T-type inverter. The effects of pulse shaping and skipping have been investigated and discussed. In addition, the voltage drop of the switching devices has been considered in conjunction with the conduction path of the T-type inverter. Compensation methods based on the pulse width modulation (PWM) of T-type inverter to alleviate the inverter nonlinearity have been proposed from research results. The proposed methods could be easily implemented by adding appropriate offset voltages to the voltage references of the inverter in PWM. Furthermore, a neutral voltage balancing method of a three-level T-type inverter has been proposed in conjunction with the proposed PWM methods using offset voltage. Through extensive experimental tests, the fifth- and seventh-harmonic components of the current are conspicuously reduced along with the even harmonics. The neutral voltage of the inverter can be balanced effectively with the proposed offset voltage adjustments as well. [ABSTRACT FROM AUTHOR]

It is important to improve the overall efficiency of a photovoltaic (PV) inverter when it is connected to the grid. Fundamentally, the conversion efficiency from dc to ac power of an inverter is important. However, in the presence of partial shading, maximum power point tracking (MPPT) on PV modules is more important than the conversion efficiency. In this paper, a new control method for a three-level inverter is proposed. With the proposed method, each dc-link voltage of the three-level inverter can be asymmetrically regulated. When PV modules are split into two and each split module is connected to the respective dc-link capacitors of the inverter, the asymmetric control can be helpful because separate MPPTs are possible. The effectiveness of the proposed method was examined through experiments with a T-type three-level inverter, where each dc-link capacitor was supplied by a PV simulator emulating two separate PV modules under different shading conditions. [ABSTRACT FROM AUTHOR]

This paper presents a novel flux-weakening strategy for an induction machine driven by an electrolytic-capacitor-less inverter. In the electrolytic-capacitor-less inverter, the dc-link voltage is fluctuating at six times the frequency of the input three-phase source due to its small dc-link capacitance. Hence, the decoupling of the fluctuation and maximum utilization of the dc-link voltage is a major issue in the electrolytic-capacitor-less inverter. In this paper, the cost function is set to increase the voltage utilization of the inverter for the flux-weakening operation of an induction machine. With the proposed flux-weakening strategy, the operating speed of the induction machine is extended above the base speed without any stability problems. The experimental results show the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]