Search

In inertial confinement fusion experiments, the neutron yield is an important metric for thermonuclear fusion performance. Neutron activation diagnostics can be used to infer neutron yields. The material used for neutron activation diagnostic undergoes a threshold reaction so that only neutrons having energies above the threshold energy are observed. For thermonuclear experiments using deuterium (D) and tritium (T) fuel constituents, neutrons arising from D + D reactions (DD-neutrons) and neutrons resulting from D + T reactions (DT-neutrons) are of primary interest. Indium has two neutron activation reactions that can be used to infer yields of DD-neutrons and DT-neutrons. One threshold is high enough that only DT-neutrons can induce activation, the second reaction can be activated by both DD-neutrons and DT-neutrons. Thus, to obtain the DD-neutron yield, the contribution made by DT-neutrons to the total induced activity must be extracted. In DD-fuel experiments, DT-neutrons arise from secondary reactions, which are significantly lower in number than primary DD-neutrons, and their contribution to the inferred DD-neutron yield can be ignored. When the DD- and DT-neutron yields become comparable, such as when low tritium fractions are added to DD-fuel, the contribution of DT-neutrons must be extracted to obtain accurate yields. A general method is described for this correction to DD-neutron yields. [ABSTRACT FROM AUTHOR]

Experiments on the Z accelerator with deuterium gas-puff implosions have produced up to 3.7×1013 (±20%) neutrons at 2.34 MeV (±0.10 MeV). Although the mechanism for generating these neutrons was not definitively identified, this neutron output is 100 times more than previously observed from neutron-producing experiments at Z. Dopant gases in the deuterium (argon and chlorine) were used to study implosion characteristics and stagnated plasma conditions through x-ray yield measurements and spectroscopy. Magnetohydrodynamic (MHD) calculations have suggested that the dopants improved the neutron output through better plasma compression, which has been studied in experiments increasing the dopant fraction. Scaling these experiments, and additional MHD calculations, suggest that ∼5×1014 deuterium-deuterium (DD) neutrons could be generated at the 26-MA refurbished Z facility. [ABSTRACT FROM AUTHOR]

A deuterium gas-puff load imploded by a multi-MA current driver from a large initial diameter could be a powerful source of fusion neutrons, a plasma neutron source (PNS). Unlike the beam-target neutrons produced in Z-pinch plasmas in the 1950s and deuterium-fiber experiments in the 1980s, the neutrons generated in deuterium gas-puffs with current levels achieved in recent experiments on the Z facility at Sandia National Laboratories could contain a substantial fraction of thermonuclear origin. For recent deuterium gas-puff shots on Z, our analytic estimates and one- and two-dimensional simulations predict thermal neutron yields ∼3×1013, in fair agreement with the yields recently measured on Z [C. A. Coverdale et al., Phys. Plasmas (to be published)]. It is demonstrated that the hypothesis of a beam-target origin of the observed fusion neutrons implies a very high Z-pinch-driver-to-fast-ions energy transfer efficiency, 5 to 10%, which would make a multi-MA deuterium Z-pinch the most efficient light-ion accelerator. No matter what mechanism is eventually determined to be responsible for generating fusion neutrons in deuterium gas-puff shots on Z, the deuterium neutron yield is shown to scale as Yn∼Im4, where Im is the peak current of the pinch. Theoretical estimates and numerical modeling of deuterium gas-puff implosions demonstrate that the yields of thermonuclear fusion neutrons that can be produced on ZR and the next-generation machines are sufficiently high to make PNS the most powerful, cost- and energy-efficient laboratory sources of 2.5-14 MeV fusion neutrons, just like plasma radiation sources are the most powerful sources of soft and keV x rays. In particular, the predicted deuterium-tritium thermal neutron-producing capability of PNS driven by the next-generation ZR and ZX accelerators is ∼5×1016 and ∼1018, respectively. [ABSTRACT FROM AUTHOR]

Experiments on the Z accelerator with deuterium gas puff implosions have produced up to 3.9×1013 (±20%) neutrons at 2.34 MeV (±0.10 MeV). Experimentally, the mechanism for generating these neutrons has not been definitively identified through isotropy measurements, but activation diagnostics suggest multiple mechanisms may be responsible. One-, two-, and three-dimensional magnetohydrodynamic (MHD) calculations have indicated that thermonuclear outputs from Z could be expected to be in the (0.3–1.0)×1014 range. X-ray diagnostics of plasma conditions, fielded to look at dopant materials in the deuterium, have shown that the stagnated deuterium plasma achieved electron temperatures of 2.2 keV and ion densities of 2×1020 cm-3, in agreement with the MHD calculations. [ABSTRACT FROM AUTHOR]

The 350-keV Cockroft-Walton accelerator at Sandia National laboratory's Ion Beam facility is being used to calibrate absolutely a total DT neutron yield diagnostic based on the 63Cu(n,2n)62Cu(β+) reaction. These investigations have led to first-order uncertainties approaching 5% or better. The experiments employ the associated-particle technique. Deuterons at 175 keV impinge a 2.6 μm thick erbium tritide target producing 14.1 MeV neutrons from the T(d,n)4He reaction. The alpha particles emitted are measured at two angles relative to the beam direction and used to infer the neutron flux on a copper sample. The induced 62Cu activity is then measured and related to the neutron flux. This method is known as the F-factor technique. Description of the associated-particle method, copper sample geometries employed, and the present estimates of the uncertainties to the F-factor obtained are given. [ABSTRACT FROM AUTHOR]

A DT neutron yield diagnostic based on the reactions, 63Cu(n,2n)62Cu(β+) and 65Cu(n,2n) 64 Cu(β+), has been fielded at the National Ignition Facility (NIF). The induced copper activity is measured using a NaI γ-γ coincidence system. Uncertainties in the 14-MeV DT yield measurements are on the order of 7% to 8%. In addition to measuring yield, the ratio of activities induced in two, well-separated copper samples are used to measure the relative anisotropy of the fuel ρR to uncertainties as low as 5%. [ABSTRACT FROM AUTHOR]