Search

Objectives: To assess the adjunctive effect of systemic amoxicillin (AMX) and metronidazole (MTZ) in patients receiving non-surgical treatment (NST) for peri-implantitis (PI)., Materials and Methods: Thirty-seven patients were randomized into an experimental group treated with NST plus AMX + MTZ (N = 18) and a control group treated with NST alone (N = 19). Clinical parameters were evaluated at 12 weeks post-treatment. The primary outcome was the change in peri-implant pocket depth (PIPD) from baseline to 12 weeks, while secondary outcomes included bleeding on probing (BoP), suppuration on probing (SoP), and plaque. Data analysis was performed at patient level (one target site per patient)., Results: All 37 patients completed the study. Both groups showed a significant PIPD reduction after NST. The antibiotics group showed a higher mean reduction in PIPD at 12 weeks, compared with the control group (2.28 ± 1.49 mm vs. 1.47 ± 1.95 mm), however, this difference did not reach statistical significance. There was no significant effect of various potential confounders on PIPD reduction. Neither treatment resulted in significant improvements in BoP at follow-up; 30 of 37 (81%) target sites still had BoP after treatment. Only two implants, one in each group, exhibited a successful outcome defined as PIPD < 5 mm, and absence of BoP and SoP., Conclusions: Non-surgical treatment was able to reduce PIPD at implants with PI. The adjunctive use of systemic AMX and MTZ did not show statistically significant better results compared to NST alone. NST with or without antibiotics was ineffective to completely resolve inflammation around dental implants., (© 2022 The Authors. Clinical Oral Implants Research published by John Wiley & Sons Ltd.)

Objectives: To investigate whether xenograft EB (EndoBon) is non-inferior to xenograft BO (Bio-Oss) when used in reconstructive surgery of peri-implant osseous defects., Materials and Methods: Dental patients with one implant each demonstrating peri-implantitis were randomized to receive surgical debridement and defect fill with either BO or EB. Changes in bone level (BL) and intrabony defect depth (IDD) evaluated radiographically were the primary outcomes. The secondary outcomes included changes in probing pocket depth (PPD), bleeding on probing (BoP), and suppuration on probing (SoP). All outcomes were recorded before treatment and at 6 and 12 months post-treatment., Results: Twenty-four patients (n = 11 BO, n = 13 EB) completed the study. Both groups demonstrated significant within-group improvements in all clinical and radiographic parameters at 6 and 12 months (p ≤ .001). At 12 months, both groups presented with IDD reductions of 2.5-3.0 mm on average. The inter-group differences were not statistically significant at all time points and for all the examined parameters (p > .05). While the radiographic defect fill in both groups exceeded > 1 mm and can be considered treatment success, successful treatment outcomes as defined by Consensus Reporting (no further bone loss, PPD ≤ 5 mm, no BOP, and no SoP) were identified in 2/11 (18%) BO and 0/13 (0%) EB individuals (Fisher's exact test, p = .199)., Conclusions: Within the limitations of this pilot study, the application of xenograft EB showed to be non-inferior to xenograft BO when used in reconstructive surgery of peri-implant osseous defects., (© 2020 The Authors. Clinical Oral Implants Research published by John Wiley & Sons Ltd.)

This article describes the autotransplantation of third molars to replace heavily damaged premolars and molars. Specifically, this article reports on the use of preoperative cone-beam computed tomographic planning and 3-dimensional (3D) printed replicas of donor teeth to prepare artificial tooth sockets. In the present case, an 18-year-old patient underwent autotransplantation of 3 third molars to replace 1 premolar and 2 molars that were heavily damaged after trauma. Approximately 1 year after the traumatic incident, autotransplantation with the help of 3D planning and rapid prototyping was performed. The right maxillary third molar replaced the right maxillary first premolar. The 2 mandibular wisdom teeth replaced the left mandibular first and second molars. During the surgical procedure, artificial tooth sockets were prepared with the help of 3D printed donor tooth copies to prevent iatrogenic damage to the actual donor teeth. These replicas of the donor teeth were designed based on the preoperative cone-beam computed tomogram and manufactured with the help of 3D printing techniques. The use of a replica of the donor tooth resulted in a predictable and straightforward procedure, with extra-alveolar times shorter than 2 minutes for all transplantations. The transplanted teeth were placed in infraocclusion and fixed with a suture splint. Postoperative follow-up showed physiologic integration of the transplanted teeth and a successful outcome for all transplants. In conclusion, this technique facilitates a straightforward and predictable procedure for autotransplantation of third molars. The use of printed analogues of the donor teeth decreases the risk of iatrogenic damage and the extra-alveolar time of the transplanted tooth is minimized. This facilitates a successful outcome., (Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)

Background and Objective: The aim of the study was to compare the detection of Porphyromonas gingivalis using a fluorescence resonance energy transfer (FRET) technology with commonly used diagnostic methods in salivary and subgingival plaque samples from subjects with dental implants. P. gingivalis was considered as a marker for a pathogenic microbiota., Material and Methods: Ninety-seven adult subjects were recruited, including periodontally healthy controls with no dental implants, implant controls with no peri-implant disease and patients with peri-implant disease. Saliva and subgingival/submucosal plaque samples were collected from all subjects and were analyzed using culture, real-time PCR and FRET technology employing P. gingivalis-specific substrates., Results: It was found that the P. gingivalis-specific substrates were highly suitable for detecting the presence of P. gingivalis in saliva and in subgingival plaque samples, showing comparable specificity to culture and real-time PCR., Conclusion: We applied the FRET technology to detect P. gingivalis in implant patients with or without an implant condition and in controls without implants. The technique seems suitable for detection of P. gingivalis in both plaque and saliva samples. However, with all three techniques, P. gingivalis was not very specific for peri-implantitis cases. Future work includes fine-tuning the FRET technology and also includes the development of a chair-side application., (© 2012 John Wiley & Sons A/S.)