Search

Background: The number of patients treated with coagulation disorders, and more specifically with anticoagulant therapy, has increased worldwide in recent years due to increased life expectancy in developed countries. The protocols for managing this type of patient in oral surgery has varied over recent years, especially after the appearance of new direct-acting oral anticoagulants (DOACs). The assessment of risk of bleeding in this type of patient when undergoing a surgical procedure continues to be a controversial issue for patients, dentists and general practitioners. The objective of this document is to offer recommendations, based on evidence, for decision making for patients with coagulopathies who require dental surgical intervention. Material and Methods: Based on the indications of the "Preparation of Clinical Practice guidelines in the National Health System. Methodological manual", we gathered a group of experts who agreed on 15 PICO questions based on managing patients with coagulation disorders in dental surgical procedures, such as fitting of implants or dental extractions. Results: The 15 PICO questions were answered based on the available evidence, being limited in most cases due to the lack of a control group. Two of the PICO questions were answered by the experts with a grade C recommendation, while the rest were answered with grade D. Conclusions: The results of this review highlight the need to undertake well designed clinical trials with control groups and with a representative sample size. [ABSTRACT FROM AUTHOR]

Background: The insertion torque of dental implants will depend on a combination of different factors such as bone density, the design of the implant and the drilling protocol used. However, it is not clear how the interaction of these factors affects the final insertion torque and which drilling protocol should be used in each clinical situation. The aim of this work is to analyse the influence of bone density, implant diameter and implant length on the insertion torque using different drilling protocols. Material and Methods: An experimental study was carried out in which the maximum insertion torque was measured, in standardised polyurethane blocks (Sawbones Europe AB) of four densities, for M12 Oxtein dental implants (Oxtein, Spain) with diameters of 3.5, 4.0, 4.5 and 5mm, and lengths of 8.5mm, 11.5mm and 14.5mm. All these measurements were carried out following four drilling protocols, a standard protocol, adding a bone tap, cortical drill or conical drill. In this way, a total of 576 samples were obtained. For the statistical analysis, the table of confidence intervals, mean, standard deviation and covariance was carried out, in total and grouped by the parameters used. Results: The insertion torque for D1 bone obtained very high levels, reaching 77± 6.95 N/cm, these values improved with the use of conical drills. In D2 bone, the mean torque obtained was 37.89± 13.70N/cm, with values within the standard. In D3 and D4 bone significantly low torques were obtained with values of 14.97± 4.40N/cm and 9.88± 4.16N/cm (p>0.001) respectively. Conclusions: In D1 bone, conical drills must be incorporated in drilling to avoid excessive torque, while in D3 and D4 bone, these would be contraindicated, as they drastically decrease the insertion torque, which may compromise the treatment. [ABSTRACT FROM AUTHOR]

Background: The aim of the present prospective clinical study is to compare the stability of the implant-bone interface by the ISQ quotient and marginal bone loss (MBL) rate during one year of follow-up in four system implants with the same surface and different design. Material and Methods: Prospective randomized clinical trial of 21 patients in which four implant systems with the same surface and different design were placed. Patients were treated by the same operator following a similar surgical protocol with submerged technique. The second surgery to perform the prosthesis was performed at 3 months. All patients went to their review at 6 months and a year. A periapical radiograph for crestal bone analysis and an Implant stability quotient by resonance frequency analysis (ISQ) analysis were taken at baseline and the reviews. Results: No statistically significant differences were found in the Implant stability quotient by resonance frequency analysis and Marginal Bone Loss in the four types of implants. The ISQ increased from the moment of insertion of the implant until the revision to the year, showing an increase of the stability implant, being this increasing less between the 6 months and the year. Conclusions: Differences in the design of the four implants tested in this study did not show statistically significant differences in any of the variables studied, so the implant design does not influence implant stability and marginal bone loss in the first year after placement. [ABSTRACT FROM AUTHOR]