Search

The Disposal of Scrap Tires has Resulted in Major Environmental Problems Worldwide. Therefore, Utilizing Scrap Tires as Crumb Rubber is being Used in Brick Production to Improve the Properties of the Bricks as well as to Provide Feasible Waste Management of Scrap Tires. this Study Presents the Literature Research on Utilizing Crumb Rubber in Bricks Manufacturing. the Review Summarized the Manufacturing Process of Producing Crumb Rubber and then Documented the Application of Crumb Rubber in Masonry. the Results Show that the Compressive Strength of Masonry Bricks Decreases with the Increased Percentage Substitution of Crumb Rubber as a Replacement of Fine Aggregate while the Water Absorption Increased. Moreover, the Addition of Crumb Rubber in Masonry Applications Reduce the Density which Produce Lightweight Masonry Products. Generally, the Findings Confirmed that the Masonry Bricks Incorporated Crumb Rubber Exhibit Good Physical and Mechanical Properties. the Usage of Crumb Rubber in Bricks Making Helps to Solve Problems Associated with Scrap Tire Management all over the World.

The rapid growth in the construction industry has dictated the utilisation of the eco-friendly materials and recycling of wastes to produce sustainable products. In this study, rubberized concrete interlocking bricks have been developed by utilising crumb rubber (10%) and fly ash (56%) as partial replacements of sand and OPC, respectively. It is aimed to develop mean and characteristic compressive strength correlations of rubberized concrete interlocking hollow and grouted wall systems, corresponding to rubberized concrete interlocking brick and prism strengths. A systematic investigation of 20 rubberized concrete interlocking brick units, 10 hollow and grouted rubberized concrete interlocking prisms and 10 identical hollow and grouted rubberized concrete interlocking wall panels were cast, constructed and tested under compressive load. Results were statistically analysed and the design-charts for the mean and characteristic compressive strength of masonry were used. The results obtained for the strength of rubberized concrete interlocking brick, prism and wall revealed a normal distribution with 5% significant interval. Four types of regression models were proposed for statistical analysis and the best fit model was identified based on r2 (correlation coefficient). The power model for the mean and characteristic strength curves presented the best fit to the sorted data. The cracking pattern and modes of failure of the tested specimens were discussed. The relationships for characteristic strengths of rubberized concrete interlocking masonry hollow and grouted wall were derived in terms of rubberized concrete interlocking unit and prism strength and found to be fkw = 1.533fb 0.290, fkw = 2.178fb 0.337 and fkw = 1.119fp0.659, fkw = 1.023fp0.731, respectively.

Researchers have used crumb rubber in the manufacturing of engineered cementitious composites (ECC) as a solution for spalling, however, it reduces the mechanical and physical properties. Therefore, this research reviews the available and related literature reviews on rubberized ECC and its constituent. The role of each constituent in a rubberized ECC mix is also reviewed. It’s concluded that utilizing rubberized ECC helps to solve environmental issues relating to improper disposal of tyres. As a result, fly ash has been the most common substance utilized in rubberized ECC by scholars all over the world over the past years because of its encouraging impacts on rheology, matrix toughness control, and interactive effect between fiber and matrix. It’s also found that the rectification of the crumb rubber drawbacks in ECC is by incorporating a modern method of adopting nano-silica, Polyvinyl alcohol (PVA) fibers, graphene oxide into the rubberized ECC mixes. Therefore, rubberized ECC can be utilized for civil engineering applications, especially with the inclusion of nano-silica and graphene oxide, as a result of its high ductility and low permeability.

Due to low water-cement ratio of self-compacting concrete (SCC), the concrete tends to be brittle. The inclusion of crumb rubber as aggregate replacement in SCC mixture has been proven to increase the properties of the SCC. Despite that the addition of the crumb rubber reduced the mechanical properties such as compressive strength, flexural strength etc. Therefore, this study is carried out to evaluate the physical performance of rubberized self-compacting concrete (R-SCC) with inclusion of nano-silica. The slump flow test, L-Box test and V-Funnel test were carried out and indicated that the flowability and viscosity of the R-SCC increase with the inclusion of fly ash and with the addition of nano-silica. The inclusion of nano-silica into the mixture improved the flowability of the concrete as well as the slump flow spread. The addition of 2% of nano-silica into the R-SCC mixture improved the passing ability of the concrete which consider the optimal addition percentage.

The application of 10% crumb rubber and 56% fly ash to partial replacement of fine aggregations and cement, respectively, by volume has formed rubberized interlocking bricks (RIBs). RIBs have been produced by semi-automatic interlocking pressing machine. This study aimed to extend previous research on the characteristics of newly developed RIBs. The initial rate of suction, dry density, efflorescence, thermal conductivity, and the elevated temperature was conducted. It was found that RIBs exhibited a lower density and higher initial rate of suction, as well as better thermal conductivity. The RIB’s compressive strength decreased while the porosity increased with the increase in the elevated temperature.

Engineered cementitious composite (ECC) was discovered as a new substitute of conventional concrete as it provides better results in terms of tensile strain, reaching beyond 3%. From then, more studies were done to partially replace crumb rubber with sand to achieve a more sustainable and eco-friendlier composite from the original ECC. However, the elastic modulus of ECC was noticeably degraded. This could bring potential unseen dangerous consequences as the fatigue might happen at any time without any sign. The replacement of crumb rubber was then found to not only bring a more sustainable and eco-friendlier result but also increase the ductility and the durability of the composite, with lighter specific gravity compared to conventional concrete. This study investigated the effects of crumb rubber (CR) and graphene oxide (GO) toward the deformable properties of rubberized ECC, including the compressive strength, elastic modulus, Poisson&rsquo, s ratio, and drying shrinkage. Central composite design (CCD) was utilized to provide 13 reasonable trial mixtures with the ranging level of CR replacement from 0&ndash, 30% and that of GO from 0.01&ndash, 0.08%. The results show that GO increased the strength of the developed GO-RECC. It was also found that the addition of CR and GO to ECC brought a notable improvement in mechanical and deformable properties. The predicted model that was developed using response surface methodology (RSM) shows that the variables (compression strength, elastic modulus, Poisson&rsquo, s ratio, and drying shrinkage) rely on the independent (CR and GO) variables and are highly correlated.

Fine aggregate and cement have been partially replaced by 10% and 56% crumb rubber and class F-fly ash, respectively, in order to manufacture rubberized concrete interlocking bricks (RCIBs). The newly developed product has been used for masonry construction without the need for mortar (mortarless), and the experimental testing under compression load was investigated by Al-Fakih et al. Therefore, in line with that, this study carried out finite element (FE) analysis for experimental result validation of masonry walls and prisms made of RCIBs. ANSYS software was utilized to implement the FE analysis, and a plasticity detailed micro-modeling approach was adopted. Parametric studies were carried out on masonry prisms to investigate the effect of the slenderness ratio and the elastic modulus of grout on the prism behavior. The results found that the adopted FE model has the ability to predict the structural response, such as compressive strength, stiffness, and failure mechanism, of the interlocking masonry prisms with about a 90% agreement with the experimental results. Based on the parametric studies, the compressive strength for a 6-course prism is approximately 68% less than a 3-course prism and 60% less than a 5-course prism, which means that the slenderness ratio plays a vital role in the behavior of the RCIB masonry prism under the vertical compression load. Moreover, the results showed that the difference between FE and experimental results of the walls was less than 16%, indicating a good match. The findings also reported that masonry walls and prisms experienced higher ductility measured by the post-failure loading under compression. The finite element model can be used for further investigation of masonry systems built with rubberized concrete interlocking bricks.

Waste tires contribute badly to the environment on a huge scale as they are bulky, non-biodegradable, and prone to fire and being a shelter for mosquitos and other insects. This paper reports on a novel approach towards the development of rubberized brick by utilizing crumb rubber as the sole fine aggregate in the production of geopolymer interlocking bricks. The response surface methodology (RSM) from Design Experts software has been used to determine the numbers of trial mixes and their corresponding ingredients. A total of thirteen trial mixes were carried out and tested for compressive strength and the RSM model was developed to predict the design mix based on the targeted compressive strength. The mix design was obtained to be an 18 M for NaOH and 0.8 solution to fly ash ratio. The geopolymer interlocking rubberized bricks were then produced and tested for compressive strength, dimension, modulus of rupture, water absorption, initial rate of absorption, and efflorescence. The geopolymer interlocking rubberised bricks presented a low compressive and flexural strength and a high-water absorption capacity. The bricks were rated as non-effloresced and classified as 3rd class bricks which can be used as non-load bearing material. It is recommended to utilize nano silica in order to increase the strength of the brick. Keywords: Rubberized bricks, Crumb rubber, Interlocking bricks, Geopolymer, Response surface methodology

Waste and industrial by-products, such as crumb rubber and fly ash, are being utilized as raw materials for making various masonry products. Rubberized concrete interlocking brick (RIB) is a newly developed product incorporated 10% crumb rubber, as a partial replacement for sand, and 56% fly ash, as a partial replacement for cement. The study experimentally emphasized understanding the behavior of masonry walls made of the developed rubberized interlocking bricks under out-of-plane load, with and without precompression load. The compressive strength of the developed loadbearing RIB was 18.4 MPa. The results of flexural strength, moment–curvature relationship, displacement responses, joint opening, and failure modes for masonry walls made of the developed RIB under lateral load parallel to the dry bed joints are discussed. An analytical analysis to predict the cracking flexural load is presented and compared with the experimental results. The results show that by increasing the pre-compression load, flexural strength, and moment capacity of the rubberized interlocking masonry walls increased linearly. The lateral displacement was 10.82, 24.99, and 29.69 mm for masonry walls subjected to a 0, 56, and 112 kN pre-compression loads, respectively. Flexural failure along the width of masonry walls with a course opening at mid-height was the dominant failure mode. It can also be concluded that the theoretical cracking flexural load closely matches the laboratory load.

This paper reports the findings of the effect of elevated temperature on the compressive strength and durability properties of crumb rubber engineered cementitious composite (CR-ECC). The CR-ECC has been tested for its compressive strength and chemical resistance test against acid and sulphate attack. Different proportions of crumb rubber (CR) in partial replacement to the fine aggregate and polyvinyl alcohol (PVA) fiber have been utilized from 0 to 5% and 0 to 2%. The experiments were designed based on a central composite design (CCD) technique of response surface methodology (RSM). After 28 days curing, the samples were preconditioned and exposed to high temperatures of 100 &deg, C, 200 &deg, C, 300 &deg, C, 400 &deg, C, 500 &deg, C, 600 &deg, C, 700 &deg, C, 800 &deg, C, 900 &deg, C, and 1000 &deg, C for one hour. Although the residual compressive strength of CR-ECC was negatively affected by elevated temperature, no explosive spalling was noticed for all mixes, even at 1000 &deg, C. Results indicated that CR-ECC experiences slight weight gain and a reduction in strength when exposed to the acidic environment. Due to the reduced permeability, CR-ECC experienced less effect when in sulphate environment. The response models were generated and validated by analysis of variance (ANOVA). The difference between adjusted R-squared and predicted R-squared values for each model was less than 0.2, and they possess at least a 95% level of confidence.

The behavior of rubberized interlocking masonry walls is substantially influenced by the properties of the waste materials used, which makes them behave differently from conventional interlocking masonry systems. Ten each of hollow and grouted walls were constructed using rubberized interlocking bricks and then tested under compressive loading. Rubberized interlocking bricks are made using 10% crumb rubber and 56% fly ash as a partial replacement for fine aggregates and cement by volume, respectively. The structural behavior, including strength, load-deformation performance, stress-strain relations, and failure mechanisms of the tested load-bearing walls have been investigated. The results reveal the ability of rubberized interlocking masonry walls to withstand axial compressive of 3.87 MPa for hollow and 5.75 MPa for grouted specimens, which is approximately 15–20% lower than in conventional interlocking masonry walls. Web splitting, vertical cracking and face spalling were common failure modes for hollow and grouted rubberized interlocking masonry walls. In contrast to conventional interlocking walls under compressive loading, rubberized interlocking walls show increased ductility and undergo measurable post-failure loads with significant displacement due to the presence of crumb rubber, which permits a large expansion of microcracks inside the specimens after failure. Rubberized interlocking walls also tend to have large initial deflections as the bricks settle and the gaps caused by dry joints close.