Search

The breath-figure method using the condensation of water droplets can easily fabricate regular porous films. Although the method is simple, the phenomenon itself requires the control of man...

We investigated the pitches of cholesteric liquid crystals prepared by mixing disodium cromoglycate (DSCG) in water with 5 different water-soluble chiral additives. The measurements are based on the Grandjean-Cano wedge cell method. Overall, the twisting effect is weak, and the shortest pitch of 2.9 ± 0.2 μm is obtained using trans-4-hydroxy-l-proline, by which the cholesteric sample is iridescent at certain viewing angles. Freeze-fracture transmission electron microscopy (FFTEM) was also performed for the first time on both the nematic and cholesteric phases, revealing that stacked chromonic aggregates are very long, up to a few hundred nm, which explains why cholesteric chromonic liquid crystals hardly have pitches in the visible wavelength region.

Effect of ferroelectricity on the photorefractive effect of ferroelectric liquid crystal blends was investigated. The photorefractive effect of ferroelectric liquid crystal blends strongly depend o...

Fabrication of regularly porous films by the breath-figure method has attracted much attention. The simple, low-cost technique uses the condensation of water droplets to produce these structures, but the phenomenon itself is complex, requiring control over many interacting parameters that change throughout the process. Developing a unified understanding for the molecular design of polymers to prepare ordered porous films is challenging, but required for further advancements. In this article, the effects of the chemical structure of polymers in the breath-figure technique were systematically explored using side-chain-type liquid-crystalline star polymers. The formation of porous films was affected by the structure of the polymers. Although the entire film surface of poly(11-[4-(4-cyanobiphenyl)oxy]undecyl methacrylate) (P11CB) had a hexagonal ordered porous structure over a certain Mn value, regularly arranged holes did not easily form in poly(methyl methacrylate) (PMMA), even though the main chain of PMMA...

The photorefractive effect in ferroelectric liquid crystalline mixtures containing photoconductive chiral compounds was investigated. Ter-thiophene compounds with chiral structures were chosen as the photoconductive chiral compounds, and they were mixed with an achiral smectic C liquid crystal. The mixtures exhibit the ferroelectric chiral smectic C phase. The photorefractivity of the mixtures was investigated by two-beam coupling experiments. It was found that the ferroelectric liquid crystals containing the photoconductive chiral compound exhibit a large gain coefficient of over 1200 cm−1 and a fast response time of 1 ms. Real-time dynamic amplification of an optical image signal of over 30 fps using the photorefractive ferroelectric liquid crystal was demonstrated.

Star polymers with sulfonyl groups in the central core were prepared by ATRP and the degradation of their cores was investigated. The core of the star polymer was efficiently and selectively decomposed by piperidine. Furthermore, the star polymer with mesogens in the side chain showed almost the same LC-isotropic phase transition temperature as the resulting degradation product, demonstrating the independence of polymer architecture on LC properties.

We prepared crosslinked azobenzene liquid-crystalline polymer brushes on flexible polymer films by surface-initiated atom transfer radical polymerization and a subsequent crosslinking reaction. Reversible isomerization of azobenzene moieties was observed in the crosslinked films upon irradiation with UV and visible light. Upon exposure to linearly polarized UV light, the films bent slightly along the polarization direction of light toward an actinic light source. After turning off the UV light, the films maintained the bent shape, and then reverted to the initial form by irradiation with visible light. We have successfully developed a novel photomobile material with crosslinked azobenzene liquid-crystalline polymer brushes.

We proposed a new approach to fabricate bilayer films with a crosslinked azobenzene liquid-crystalline (LC) polymer. The polyethylene (PE) substrates were coated with linear azobenzene LC polymers, and then the azobenzene layers were crosslinked by irradiation with electron beams (EBs). In the EB-irradiated films with ordered azobenzene moieties, exposure to UV light caused trans-cis isomerization and the change in alignment of azobenzene moieties. Bending of the bilayer films could be induced toward an actinic light source when they were irradiated from the side of the azobenzene layer, while they bent away from the actinic light source upon UV irradiation from the side of the PE layer. In both cases, the bent films reverted to the initial flat state by turning off the light, which could be repeated at room temperature.

Two azobenzene-containing block copolymers with an oxyethylene (P1) or an alkyl (P2) spacer in the side chain were prepared by atom transfer radical polymerization (ATRP). Neither of the block copolymers with a low azobenzene content showed a liquid-crystalline phase. However, their glass transition temperatures (T gs) were lowered by introducing flexible spacers. In particular, T g was lowered by about 30°C in P1. Their photoalignment and holographic behavior was investigated at various temperatures in thin films. Rapid changes in refractive index were induced in the P1 films upon irradiation at a temperature below T g. But the photoinduced birefringence in the P1 film was lower than that in the P2 films. Similar results were obtained in holographic recording. The azobenzene-containing block copolymer with the oxyethylene spacer (P1) used in this study has potential application for dynamic hologram.

We prepared homogeneously aligned azobenzene liquid-crystalline elastomer (LCE) films with low T g and explored their photomechanical properties. Upon irradiation with UV light, the films bent toward a light source at room temperature. The mechanical force generated upon exposure to UV light was evaluated by thermomechanical analysis. It was found that the mechanical force generated by photo-irradiation increased with an increase in the cross-linking density. In particular, an LCE film containing 80 mol% azobenzene cross-linker produced a force of over 1 MPa by photo-irradiation, which enabled the film to lift an object 20 times heavier than itself. The degree of contraction by photo-irradiation increased with an increase in temperature and light intensity. Bending could be brought about by more than 5000 times with periodic irradiation. Furthermore, it was found that the LCE films exhibited bending and unbending behaviour by irradiation with sunlight.

A block copolymer containing an azobenzene (Az) moiety in the side chain was prepared by atom transfer radical polymerization (ATRP). For comparison, a random copolymer with a similar Az content was also designed. Their photoresponsive and holographic behavior was investigated in thin films. The block copolymer film showed microphase separation with cylinder microdomains after annealing, which was then irradiated at 366 nm. It was found that trans-cis photoisomerization in the block copolymer film was slower than that in the random copolymer film. This may be due to the restricted motion of the Az moieties in the Az blocks. The photoinduced birefringence (Δn) of the block copolymer film was higher than that of the random copolymer film upon irradiation with a linearly polarized beam. In holographic recording, similar results were obtained. A block copolymer with 22-mol% Az showed a liquid-crystalline (LC) phase, while a random copolymer with 24-mol% Az exhibited no LC phase. The block copolymer showed an ...

To precisely control the first-order diffraction efficiency of holographic gratings recorded in an amphiphilic diblock liquid-crystalline copolymer P40A37, effect of recording time on grating formation and enhancement was studied systematically. Several parameters such as surface relief, the first-order diffraction efficiency, the maximum transmittance under an optical polarizing microscope and order parameters of grating samples were evaluated before and after annealing. Then the enhancement coefficient with recording time was estimated. The best enhancement effect was obtained at 10-s recording upon nano-scaled phase separation. By precisely adjusting the recording time, the diffraction efficiency of holographic gratings in P40A37 can be finely controlled from 0.13% to 10%.