Search

An overview of the recent operations and the main results of cesium injection in the Source for the Production of Ions of Deuterium Extracted from Rf plasma (SPIDER) negative ion source are described in this contribution. In experiments without cesium injection, all SPIDER plants were tested to verify the basic expectations on the operational parameters (e.g., electron cooling effectiveness of magnetic filter field) and to determine its operational region. For beam properties, it was shown that the current density varies across the beam in the vertical direction. In preliminary cesium experiments, the expected increase of negative ion current and simultaneous decrease of co-extracted electrons were found, along with the influence of the control parameters (polarization of the plasma electrodes, magnetic filter field) on the SPIDER beam uniformity in the horizontal and vertical directions. It was shown that non-Gaussian tails can be identified in the angular distribution on the plane perpendicular to the beam propagation direction. Stray particles, nonhomogeneous beam and large divergence might result in unexpected heat and particle loads over ITER neutral beam injector (NBI) accelerator grids; it is the goal of SPIDER to assess and possibly to identify suitable methods for controlling these beam features. A major shutdown, planned for late 2021, to solve the issues identified during the operation and to carry out scheduled modifications, is outlined. Such improvements are expected to allow SPIDER to pursue the ITER requirements in terms of negative ion current, electron-to-ion ratio, and beam duration.

SPIDER (Source for the Production of Ions of Deuterium Extracted from a Radio frequency plasma) is the full-scale prototype for the ITER Heating Neutral Beam (HNB) source. Driven by four driver coil pairs powered by oscillators the SPIDER source plasma exhibits fluctuations in a range of frequencies that have been observed by Langmuir probes and Source Emission Spectroscopy. These fluctuations are believed to influence the extracted beam current, meniscus shape and beam features. Beam operation in SPIDER, with the eventual aim of achieving 100 keV, 46 A hydrogen negative ion beam for one hour, has mainly been performed in volume operation. Recently, with the introduction of caesium, SPIDER has moved to the surface operation, with a noted increase in beam current. Electrical and calorimetric measurements of the beam current have shown discrepancies between the two, possibly due to background gas interactions. Taking advantage of the reduced number of beamlets due to the Plasma Grid mask a series of Hall effect current transducers and AC current transformers have been installed in SPIDER. These Beamlet Current Monitors (BCMs), positioned downstream of the Grounded Grid, provide a direct measurement of the current of up to five individual beamlets, from DC up to 5MHz frequencies. This contribution describes the initial results from the BCM with and without caesium, focussing on the characterisation of the beamlet direct current component.

The electrical insulation of the Megavolt ITER Injector and Concept Advancement (MITICA) beam source (BS) at 1 MV in vacuum is a challenging issue, which could not be fully addressed so far on the basis of experimental results and of theoretical models available in literature. A specific high-voltage (HV) test campaign is being prepared to validate and optimize the voltage holding capability of the BS insulation under realistic conditions, using full-size mockup electrodes reproducing in detail the geometry of the BS and accelerator. The proposed test strategy will address both the single-gap and the multistage insulation, so as to obtain a verification of voltage holding at 1 MV before the installation of the real components. This approach is intended to reduce the risk related to the HV insulation at 1 MV and, if necessary, to allow the development of effective corrections. In this article, the test motivations and requirements are defined, and the electrode implementation and diagnostic setup are described. Finally, the test configurations and the experimental procedure are discussed.

The negative-ion based neutral beam injector for heating and current drive of the ITER plasma (ITER HNB) is under development, at present focusing on the optimization of the full-scale plasma source in the SPIDER test stand. The production of H− or D− ions in the ion source is based on the low work function surfaces obtained by caesium evaporation. This paper describes the caesium conditioning procedure and the corresponding beam performances during the first operation of SPIDER with caesium. Technical solutions to overcome present limitations of the test stand are described. The influence of source parameters on the caesium effectiveness was investigated in short beam pulse operation; with total radio-frequency (RF) power of 400 kW and filling pressure below 0.4 Pa, and a limited number of extraction apertures, a negative ion current density of about 200 A m−2 was extracted in hydrogen, with beam energy lower than 60 keV. Beam optics and beam uniformity were assessed thanks to the acceleration of isolated ion beamlets. A possible procedure to accelerate a uniform beam was demonstrated at low RF power. The results obtained in this first investigation provided key indications on the operation of one of the largest existing sources of accelerated negative hydrogen-like ions.