Search

An equimolar NiCoFeCrGa high entropy alloy having dual-phase homogeneous components was studied, where the constituent phases exhibit distinct mechanical properties. Micropillars with various diameters were created from two differently heat treated samples, then they were compressed at slow strain rates, that revealed the material's limited sensitivity to size. On the other hand, increased strain rate sensitivity at high deformation speeds was observed, that differs substantially depending on the phase composition of the specimen. Dislocations within the two phases were studied by high resolution transmission electron microscopy and high angular resolution electron backscatter diffraction. The performed chemical analysis confirmed that slow cooling during casting create Cr-rich precipitates, that have significant impact on the global strength of the material.

To study the size and strain rate dependency of copper polycrystalline microstructures, a multi-layered copper/Al$_2$O$_3$ thin film was deposited on a Si substrate using a hybrid deposition system (combining physical vapour and atomic layer deposition). High temperature treatment was applied on the "As Deposited" material with ultrafine-grained structure to increase the average grain size, resulting in a "Heat Treated" state with microcrystalline structure. Focused ion beam milling was employed to create square shaped micropillars with two different sizes, that were subjected to compressive loading at various (0.001/s - 1000/s) strain rates. The detected two distinct anomalies in the strain rate sensitivity behavior appearing at high strain rates could be related to the pillar diameter and the grain size of the deformed samples. The Al$_2$O$_3$ interlayer studied by transmission electron microscopy showed excellent thermal stability and grain boundary pinning by precipitation, also resulting in the homogeneous deformation of the pillars and preventing shear localization. Geometrically necessary dislocation densities estimated by high (angular) resolution electron backscatter diffraction presented inhomogeneous dislocation distribution within the deformed pillar volumes, that is attributed to the proximity of the sample edges. Finally, the Al$_2$O$_3$ interlayers successfully suppressed any possible recrystallization processes, contributing to the excellent film stability, that makes the proposed coating ideal to be operating under extreme conditions.

The mechanical performance of metallic metamaterials with 3-dimensional solid frames is typically a combination of the geometrical effect ("architecture") and the characteristic size effects of the base material ("microstructure"). In this study, for the first time, the temperature- and rate-dependent mechanical response of copper microlattices has been investigated. The microlattices were fabricated via a localized electrodeposition in liquid (LEL) process which enables high-precision additive manufacturing of metal at the micro-scale. The metal microlattices possess a unique microstructure with micron sized grains that are rich with randomly oriented growth twins and near-ideal nodal connectivity. Importantly, copper microlattices exhibited unique temperature (-150 and 25 degree C) and strain rate (0.001~100 s-1) dependent deformation behavior during in situ micromechanical testing. Systematic compression tests of fully dense copper micropillars, equivalent in diameter and length to the struts of the microlattice at comparable extreme loading conditions, allow us to investigate the intrinsic deformation mechanism of copper. Combined with the post-mortem microstructural analysis, substantial shifts in deformation mechanisms depending on the temperature and strain rate were revealed. On the one hand, at room temperature (25 degree C), dislocation slip based plastic deformation occurs and leads to a localized deformation of the micropillars. On the other hand, at cryogenic temperature (-150 degree C), mechanical twinning occurs and leads to relatively homogeneous deformation of the micropillars. Based on the intrinsic deformation mechanisms of copper, the temperature and strain rate dependent deformation behavior of microlattices could be explained.

In metals geometrically necessary dislocations (GNDs) are generated primarily to accommodate strain gradients and they play a key role in the Bauschinger effect, strain hardening, micron-scale size effects and fatigue. During bending large strain gradients naturally emerge which makes this deformation mode exceptionally suitable to study the evolution of GNDs. Here we present bi-directional bending experiment of a Cu single crystalline microcantilever with in situ characterisation of the dislocation microstructure in terms of high-resolution electron backscatter diffraction (HR-EBSD). The experiments are complemented with dislocation density modelling to provide physical understanding of the collective dislocation phenomena. We find that dislocation pile-ups form around the neutral zone during initial bending, however, these do not dissolve upon reversed loading, rather they contribute to the development of a much more complex GND dominated microstructure. This irreversible process is analysed in detail in terms of the involved Burgers vectors and slip systems to provide an in-depth explanation of the Bauschinger-effect and strain hardening at this scale. We conclude that the most dominant role in this behaviour is played by short-range dislocation interactions., Comment: manuscript submitted to Acta Materialia

Slow strain rates tests (SSRT) were conducted on hydrogen-containing specimens of PH13-8Mo maraging stainless steel. Hydrogen-assisted subcritical quasi-cleavage cracking was shown to take place during SSRT, thus accelerating material failure. Fractographic analysis showed that quasi-cleavage is composed of flat brittle areas and rougher areas. Using cross-sectional electron backscatter diffraction (EBSD) analysis of a secondary subcritically grown crack, we observed brittle cracks propagated across martensite blocks ahead the main crack tip. These cracks were stopped at high-angle boundaries. The crack direction was consistent with propagation along {100} type planes. High-resolution EBSD showed significant crystal lattice rotation, hence consequential plastic deformation, concentrated between the main crack tip and the cracks located ahead it. It is concluded that quasi-cleavage in the material investigated here consists of {100} cleavage cracks connected by ductile ridges. A discontinuous mechanism, involving re-initiation of new cleavage cracks ahead the main crack tip is suggested.

The dislocation microstructure developing during plastic deformation strongly influences the stress-strain properties of crystalline materials. The novel method of high resolution electron backscatter diffraction (HR-EBSD) offers a new perspective to study dislocation patterning. In this work copper single crystals deformed in uniaxial compression were investigated by HR-EBSD, X-ray line profile analysis, and transmission electron microscopy (TEM). With these methods the maps of the internal stress, the Nye tensor, and the geometrically necessary dislocation (GND) density were determined at different load levels. In agreement with the composite model long-range internal stress was directly observed in the cell interiors. Moreover, it is found from the fractal analysis of the GND maps that the fractal dimension of the cell structure is decreasing with increasing average spatial dislocation density fluctuation. It is shown that the evolution of different types of dislocations can be successfully monitored with this scanning electron microscopy based technique., Comment: Submitted to Journal: Materialia. Manuscript number: MTLA-D-22-00602

Microscale dynamic testing is vital to the understanding of material behavior at application relevant strain rates. However, despite two decades of intense micromechanics research, the testing of microscale metals has been largely limited to quasi-static strain rates. Here we report the dynamic compression testing of pristine 3D printed copper micropillars at strain rates from $\sim0.001$ s$^{-1}$ to $\sim500$ s$^{-1}$. It was identified that microcrystalline copper micropillars deform in a single-shear like manner exhibiting a weak strain rate dependence at all strain rates. Ultrafine grained (UFG) copper micropillars, however, deform homogenously via barreling and show strong rate-dependence and small activation volumes at strain rates up to $\sim0.1$ s$^{-1}$, suggesting dislocation nucleation as the deformation mechanism. At higher strain rates, yield stress saturates remarkably, resulting in a decrease of strain rate sensitivity by two orders of magnitude and a four-fold increase in activation volume, implying a transition in deformation mechanism to collective dislocation nucleation., Comment: Corresponding authors with equal contribution are: Szilvia Kal\'acska and Rajaprakash Ramachandramoorthy. Accepted manuscript: Applied Materials Today

Compression experiments on micron-scale specimens and acoustic emission (AE) measurements on bulk samples revealed that the dislocation motion resembles a stick-slip process - a series of unpredictable local strain bursts with a scale-free size distribution. Here we present a unique experimental set-up, which detects weak AE waves of dislocation slip during the compression of Zn micropillars. Profound correlation is observed between the energies of deformation events and the emitted AE signals that, as we conclude, are induced by the collective dissipative motion of dislocations. The AE data also reveal a surprising two-level structure of plastic events, which otherwise appear as a single stress drop. Hence, our experiments and simulations unravel the missing relationship between the properties of acoustic signals and the corresponding local deformation events. We further show by statistical analyses that despite fundamental differences in deformation mechanism and involved length- and time-scales, dislocation avalanches and earthquakes are essentially alike., Comment: Preprint submitted to Nature Communications

With decreasing system sizes, the mechanical properties and dominant deformation mechanisms of metals change. For larger scales, bulk behavior is observed that is characterized by a preservation and significant increase of dislocation content during deformation whereas at the submicron scale very localized dislocation activity as well as dislocation starvation is observed. In the transition regime it is not clear how the dislocation content is built up. This dislocation storage regime and its underlying physical mechanisms are still an open field of research. In this paper, the microstructure evolution of single crystalline copper micropillars with a $\langle1\,1\,0\rangle$ crystal orientation and varying sizes between $1$ to $10\,\mu\mathrm{m}$ is analysed under compression loading. Experimental in situ HR-EBSD measurements as well as 3d continuum dislocation dynamics simulations are presented. The experimental results provide insights into the material deformation and evolution of dislocation structures during continuous loading. This is complemented by the simulation of the dislocation density evolution considering dislocation dynamics, interactions, and reactions of the individual slip systems providing direct access to these quantities. Results are presented that show, how the plastic deformation of the material takes place and how the different slip systems are involved. A central finding is, that an increasing amount of GND density is stored in the system during loading that is located dominantly on the slip systems that are not mainly responsible for the production of plastic slip. This might be a characteristic feature of the considered size regime that has direct impact on further dislocation network formation and the corresponding contribution to plastic hardening., Comment: submitted, not yet accepted

High angular resolution electron backscatter diffraction (HR-EBSD) was coupled with focused ion beam (FIB) slicing to characterize the shape of the plastic zone in terms of geometrically necessary dislocations (GNDs) in W single crystal in 3 dimensions. Cantilevers of similar size with a notch were fabricated by FIB and were deformed inside a scanning electron microscope at different temperatures (21$^{\circ}$C, 100$^{\circ}$C and 200$^{\circ}$C) just above the micro-scale brittle-to-ductile transition (BDT). J-integral testing was performed to analyse crack growth and determine the fracture toughness. At all three temperatures the plastic zone was found to be larger close to the free surface than inside the specimen, similar to macro-scale tension tests. However, at higher temperature, the 3D shape of the plastic zone changes from being localized in front of the crack tip to a butterfly-like distribution, shielding more efficiently the crack tip and inhibiting crack propagation. A comparison was made between two identically deformed samples, which were FIB-sliced from two different directions, to evaluate the reliability of the GND density estimation by HR-EBSD. The analysis of the distribution of the Nye tensor components was used to differentiate between the types of GNDs nucleated in the sample. The role of different types of dislocations in the plastic zone is discussed and we confirm earlier findings that the micro-scale BDT of W is mainly controlled by the nucleation of screw dislocations in front of the crack tip., Comment: accepted (Acta Materialia)

Atomic force microscopy (AFM) is a well-known tool for studying surface roughness and to collect depth information about features on the top atomic layer of samples. By combining secondary ion mass spectroscopy (SIMS) with focused ion beam (FIB) milling in a scanning electron microscope (SEM), chemical information of sputtered structures can be visualized and located with high lateral and depth resolution. In this paper, a high vacuum (HV) compatible AFM has been installed in a TESCAN FIB-SEM instrument that was equipped with a time-of-flight secondary ion mass spectroscopy (ToF-SIMS) detector. To investigate the crater's depth caused by the ToF-SIMS sputtering, subsequent AFM measurements were performed on a multilayer vertical cavity surface emitting laser (VCSEL) sample. Surface roughness and milling depth were used to aid accurate 3D reconstruction of the sputtered volume's chemical composition. Achievable resolution, surface roughness during sputtering and surface oxidation issues are analysed. Thus, the integration of complementary detectors opens up the ability to determine the sample properties as well as to understand the influence of the analysis method on the sample surface during the analysis., Comment: Submitted (13 Dec. 2019) for review

Zircaloy-4 is used extensively as nuclear fuel cladding materials and hydride embrittlement is a major failure mechanism. To explore the effect of {\delta}-hydride on plastic deformation and performance of Zircaloy-4, in situ high angular resolution electron backscatter diffraction (HR-EBSD) was used to quantify stress and geometrically necessary dislocation (GND) density during bending tests of hydride-free and hydride-containing single crystal Zircaloy-4 microcantilevers. Results suggest that while the stress applied was accommodated by plastic slip in the hydride-free cantilever, the hydride-containing cantilever showed precipitation induced GND pile-up at hydride-matrix interface pre-deformation, and considerable locally increasing GND density under tensile stress upon plastic deformation., Comment: Manuscript submitted for review

Based on the cross correlation analysis of the Kikuchi diffraction patterns high-resolution EBSD is a well established method to determine the internal stress in deformed crystalline materials. In many cases, however, the stress values obtained at the different scanning points have a large (in the order of GPa) scatter. As it was first demonstrated by Wilkinson and co-workers this is due to the long tail of the probability distribution of the internal stress ($P(\sigma)$) generated by the dislocations present in the system. According to the theoretical investigations of Groma and co-workers the tail of $P(\sigma)$ is inverse cubic with prefactor proportional to the total dislocation density $<\rho>$. In this paper we present a direct comparison of the X-ray line broadening and $P(\sigma)$ obtained by EBSD on deformed Cu single crystals. It is shown that $<\rho>$ can be determined from $P(\sigma)$. This opens new perspectives for the application of EBSD in determining mesoscale parameters in a heterogeneous sample., Comment: 5 pages, 6 figures