Search

In recent years, inertial measurement units (IMUs) have been proposed as an alternative to force platforms and pressure sensors for gait events (i.e., initial and final contacts) detection. While multiple algorithms have been developed, the impact of gait event timing errors on temporal parameters and asymmetry has never been investigated in people with transfemoral amputation walking freely on level ground. In this study, five algorithms were comparatively assessed on gait data of seven people with transfemoral amputation, equipped with three IMUs mounted at the pelvis and both shanks, using pressure insoles for reference. Algorithms' performance was first quantified in terms of gait event detection rate (sensitivity, positive predictive value). Only two algorithms, based on shank mounted IMUs, achieved an acceptable detection rate (positive predictive value > 99%). For these two, accuracy of gait events timings, temporal parameters, and absolute symmetry index of stance-phase duration (SPD-ASI) were assessed. Whereas both algorithms achieved high accuracy for stride duration estimates (median errors: 0%, interquartile ranges < 1.75%), lower accuracy was found for other temporal parameters due to relatively high errors in the detection of final contact events. Furthermore, SPD-ASI derived from IMU-based algorithms proved to be significantly different to that obtained from insoles data. Graphical abstract Gait event detection with IMU in people with transfemoral amputation: initial contact (IC) and final contact (FC) events at the sound (s) and prosthetic (p) side are identified. Five algorithms were implemented using either shank-mounted or pelvis-mounted IMUs. Gait events were used to estimate temporal parameters (stride duration, stance phase duration [SPD], and double support time) and SPD asymmetry. [ABSTRACT FROM AUTHOR]

This article proposes a simple and convenient method for assessing the subject-specific rolling resistance acting on a manual wheelchair, which could be used during the provision of clinical service. This method, based on a simple mathematical equation, is sensitive to both the total mass and its fore-aft distribution, which changes with the subject, wheelchair properties, and adjustments. The rolling resistance properties of three types of front casters and four types of rear wheels were determined for two indoor surfaces commonly encountered by wheelchair users (a hard smooth surface and carpet) from measurements of a three-dimensional accelerometer during field deceleration tests performed with artificial load. The average results provided by these experiments were then used as input data to assess the rolling resistance from the mathematical equation with an acceptable accuracy on hard smooth and carpet surfaces (standard errors of the estimates were 4.4 and 3.9 N, respectively). Thus, this method can be confidently used by clinicians to help users make trade-offs between front and rear wheel types and sizes when choosing and adjusting their manual wheelchair. [ABSTRACT FROM AUTHOR]

Background: The analysis of biomechanical parameters derived from the body center of mass (BCoM) 3D motion allows for the characterization of gait impairments in people with lower-limb amputation, assisting in their rehabilitation. In this context, magneto-inertial measurement units are promising as they allow to measure the motion of body segments, and therefore potentially of the BCoM, directly in the field. Finding a compromise between the accuracy of computed parameters and the number of required sensors is paramount to transfer this technology in clinical routine.Research Question: Is there a reduced subset of instrumented segments (BSN) allowing a reliable and accurate estimation of the 3D BCoM acceleration transfemoral amputees?Methods: The contribution of each body segment to the BCoM acceleration was quantified in terms of weight and similarity in ten people with transfemoral amputation. First, body segments and BCoM accelerations were obtained using an optoelectronic system and a full-body inertial model. Based on these findings, different scenarios were explored where the use of one sensor at pelvis/trunk level and of different networks of segment-mounted sensors for the BCoM acceleration estimation was simulated and assessed against force plate-based reference acceleration.Results: Trunk, pelvis and lower-limb segments are the main contributors to the BCoM acceleration in transfemoral amputees. The trunk and shanks BSN allows for an accurate estimation of the sagittal BCoM acceleration (Normalized RMSE ≤ 13.1 %, Pearson's correlations r ≥ 0.86), while five segments are necessary when the 3D BCoM acceleration is targeted (Normalized RMSE ≤ 13.2 %, Pearson's correlations r ≥ 0.91).Significance: A network of three-to-five segments (trunk and lower limbs) allows for an accurate estimation of 2D and 3D BCoM accelerations. The use of a single pelvis- or trunk-mounted sensor does not seem advisable. Future studies should be performed to confirm these results where inertial sensor measured accelerations are considered. [ABSTRACT FROM AUTHOR]