Search

Wiebe functions, analytical equations that estimate the fuel mass fraction burned (MFB) during combustion, have been effective at describing spark-ignition (SI) engine combustion using gasoline fuels. This study explores if the same methodology can be extended for SI combustion with syngas, a gaseous fuel mixture composed of H2, CO, and CO2, and anode-off gas; the latter is an exhaust gas mixture emitted from the anode of a Solid Oxide Fuel Cell, containing H2, CO, H2O, and CO2. For this study, anode off-gas is treated as a syngas fuel diluted with CO2 and vaporized water. Combustion experiments were run on a single-cylinder, research engine using syngas and anode-off gas as fuels. One single Wiebe function and three double Wiebe functions were fitted and compared with the MFB profile calculated from the experimental data. It was determined that the SI combustion process of both the syngas and the anode-off gas could be estimated using a governing Wiebe function. While the detailed double Wiebe function had the highest accuracy, a reduced double Wiebe function is capable of achieving comparable accuracy. On the other hand, a single Wiebe function is not able to fully capture the combustion process of a SI engine using syngas and anode off-gas.

Solid oxide fuel cell – internal combustion engine (SOFC-ICE) hybrid systems are an attractive solution for electricity generation. The system can achieve up to 70% theoretical electric power conversion efficiency through energy cascading enabled by utilizing the anode off-gas from the SOFC as the fuel source for the ICE. Experimental investigations were conducted with a single cylinder Cooperative Fuel Research (CFR) engine by altering fuel-air equivalence ratio (ϕ), and compression ratio (CR) to study the engine load, combustion characteristics, and emissions levels of dry SOFC anode off-gas consisting of 33.9% H2, 15.6% CO, and 50.5% CO2. The combustion efficiency of the anode off-gas was directly evaluated by measuring the engine-out CO emissions. The highest net-indicated fuel conversion efficiency of 31.3% occurred at ϕ = 0.90 and CR = 13:1. These results demonstrate that the anode off-gas can be successfully oxidized using a spark ignition combustion mode. The fuel conversion efficiency of the anode tail gas is expected to further increase in a more modern engine architecture that can achieve increased burn rates in comparison to the CFR engine. NOx emissions from the combustion of anode off-gas were minimal as the cylinder peak temperatures never exceeded 1800 K. This experimental study ultimately demonstrates the viability of an ICE to operate using an anode off-gas, thus creating a complementary role for an ICE to be paired with a SOFC in a hybrid power generation plant.

With the rise in wood stove use in recent years, a number of experimental research efforts have been undertaken with the objective of developing cleaner, and more efficient stove designs. However, numerical modeling of stoves is still in its nascent years, thus making it imperative to start adapting more mature computational techniques, established in other combustion-based applications (e.g., combustion engines), to wood stoves. This study focuses on a critical review of the state-of-the-art in wood combustion modeling techniques and on providing recommendations for needed enhancements. In order to develop an optimum conceptual numerical model for wood stoves, the basic processes inside the stove are broken down and isolated into generic computational domains: surface reactions, gas reactions, and the fluid domain. Then state-of-the-art numerical efforts for wood stove and similar applications are broken down in a similar manner to highlight points of strength and possible improvements. Finally, based on the comparison between the different models, an improved modeling approach is proposed as a road map for future research efforts to achieve a higher fidelity wood stove numerical model., 14 pages, 10 figures, 1 table

Spark-assisted homogeneous charge compression ignition (HCCI) combustion may be a method to improve the operation of HCCI engines. In the current study, the impact of spark assist on the fundamental properties of ignition and combustion was investigated in a single cylinder, optically-accessible research engine. Early port fuel injection and air preheating were used with indolene fuel in the study. The effects of a range of air preheat ( Tin = 256–281 °C), fuel/air equivalence ratio (ϕ = 0.38–0.62) and spark assist timing (10°−90° before top dead centre) conditions on maximum in-cylinder pressure and timing, cycle variability, indicated mean effective pressure (IMEP) and heat release rate were investigated. Additionally, high-speed imaging was used to capture the piston-view ignition and combustion events during spark-assisted and unassisted HCCI operation. Methods were developed and applied to the imaging sequences to quantify the physical characteristics (e.g. location of autoignition sites) and the rate of propagation of the reaction fronts formed during spark-assisted and unassisted HCCI operation. The imaging data show that autoignition sites appear with increasing frequency as air preheat temperature is increased. The addition of spark assist led to the formation of reaction fronts at all conditions that propagated outward from the spark electrode at average speeds between 1.9 and 4.3 m/s. The imaging data indicate the effects of spark assist are due to compression heating of the unburned gases by the propagating reaction fronts which also leads to more consistent location of autoignition. Comparison of the imaging and engine data show the initial formation of the reaction fronts are not significant sources of heat release. While the engine data show that spark assist can affect phasing, heat release rate, IMEP and engine stability at the marginal HCCI operating conditions studied, the results also indicate spark assist has a narrow temperature range where the changes will be significant compared to the effects of the inherent thermal stratification of the HCCI fuel/air charge.

A thermodynamic simulation is used to study the effects of oxygen-enriched intake air on the performance and nitrogen oxide (NO) emissions of a locomotive diesel engine. The parasitic power of the air separation membrane required to supply the oxygen-enriched air is also estimated. For a given constraint on peak cylinder pressure, the gross and net power output of an engine operating under different levels of oxygen enrichment are compared with those obtained when a high-boost turbocharged engine is used. A 4 percent increase in peak cylinder pressure can result in an increase in net engine power of approximately 10 percent when intake air with an oxygen content of 28 percent by volume is used and fuel injection timing is retarded by 4 degrees. When the engine is turbocharged to a higher inlet boost, the same increase in peak cylinder pressure can improve power by only 4 percent. If part of the significantly higher exhaust enthalpies available as a result of oxygen enrichment is recovered, the power requirements of the air separator membrane can be met, resulting in substantial net power improvements. Oxygen enrichment with its attendant higher combustion temperatures, reduces emissions of particulates and visible smoke but increases NO emissions (by up to three times at 26 percent oxygen content). Therefore, exhaust gas after-treatment and heat recovery would be required if the full potential of oxygen enrichment for improving the performance of locomotive diesel engines is to be realized.

This study presents two new methods to rapidly analyze the ignition and combustion events recorded during in-cylinder high-speed imaging of homogeneous charge compression ignition (HCCI) and spark-assisted (SA) HCCI engine operation. Two categories of ignition have been observed during HCCI and SA HCCI: auto-ignition of parcels of fuel/air and ignition and propagation of reaction fronts. In this work, two methods of image analysis are developed which accommodate differences in the ignition and propagation events for the two categories. The methods are described by application to high speed imaging data acquired from an optically accessible engine operated in HCCI and SA HCCI modes using indolene fuel. Using method I, the projected area of reaction is identified in each frame, and a circle with a characteristic radius that yields the equivalent area is defined. The rate of area expansion is used to define the speed of reaction. Using method II, an edge-finding algorithm is used to identify the location of well-defined reaction fronts. The maximum dimensions of the reaction front in an x-y coordinate frame are measured. The projected area based on the average of these maximum dimensions is then determined. The change in the characteristic radius of the projected area is defined as the average propagation speed for the reaction front. The two analytical methods are applied to typical HCCI and SA HCCI image sequences. Outcomes of the image analysis indicate propagation speeds are typically between 2–5 m/s prior to volumetric ignition. Volumetric ignition is identified by propagation speeds greater than 20 m/s. The imaging data also identify times when reaction quenching occurred after spark ignition as times when negative propagation speeds are observed. When applied to the same imaging sequence, the two methods yield consistent results for propagation speeds; however, the method based on edge-finding exhibits larger variance.Copyright © 2010 by ASME

High-speed imaging combined with the optical access provided by a research engine offer the ability to directly image and compare ignition and combustion phenomena of various fuels. Such data provide valuable insight into the physical and chemical mechanisms important in each system. In this study, crank-angle resolved imaging data were used to investigate homogeneous charge compression ignition (HCCI) operation of a single-cylinder four-valve optical engine fueled using gasoline, indolene, and iso-octane. Lean operating limits were the focus of the study with the primary objective of identifying different modes of reaction front initiation and propagation for each fuel. HCCI combustion was initiated and maintained over a range of lean conditions for various fuels, from 0.69 to 0.27. The time-resolved imaging and pressure data show that high rates of heat release in HCCI combustion correlate temporally to simultaneous, intense volumetric blue emission. Lower rates of heat release are characteristic of spatially resolved blue emission. Gasoline supported leaner HCCI operation than indolene. Iso-octane showed a dramatic transition into misfire. Similar regions of preferential ignition were identified for each of the fuels considered using the imaging data. DOI: 10.1115/1.2898720

High-speed imaging combined with the optical access provided by a single-cylinder research engine offer the ability to directly study ignition and combustion phenomena. Such data provide valuable insight into the physical and chemical mechanisms important in advanced engine combustion strategies. In this study, crank-angle resolved chemiluminescence imaging data both orthogonal to and along the piston axis were used to investigate homogeneous charge compression ignition (HCCI) operation of a single-cylinder four-valve optical engine fueled using indolene. This preliminary study focused on identifying how multi-axis imaging can contribute to understanding the effects of spark-assist on HCCI performance. Operating conditions of advanced spark ignition timing for extending the lean limits of bulk charge compression ignition were used. The experiments were performed at a fixed equivalence ratio of φ = 0.56, with fixed intake conditions (wide open throttle with air preheat). The multi-axis imaging provides a clear indication of the propagation of a reaction front from the spark kernel. The combination of orthogonal and axial views may provide valuable information spatially resolving volumetric heat release, thereby providing an indication of the fractional energy release due to the spark assist compared to the energy released by auto-ignition.Copyright © 2007 by ASME

High-speed imaging combined with the optical access provided by a research engine offer the ability to directly image and compare ignition and combustion phenomena of various fuels. Such data provide valuable insight into the physical and chemical mechanisms important in each system. In this study, crank-angle resolved imaging data were used to investigate homogeneous charge compression ignition (HCCI) operation of a single-cylinder four-valve optical engine fueled using gasoline, indolene, and iso-octane. Lean operating limits were the focus of the study with the primary objective of identifying different modes of reaction front initiation and propagation for each fuel. HCCI combustion was initiated and maintained over a range of lean conditions for various fuels, from φ = 0.77 to 0.27. The time-resolved imaging and pressure data show high rates of heat release in HCCI combustion correlate temporally to simultaneous, intense volumetric blue emission. Lower rates of heat release are characteristic of spatially-resolved blue emission. Gasoline supported leaner HCCI operation than indolene. Iso-octane showed a dramatic transition into misfire. Similar regions of preferential ignition were identified for each of the fuels considered using the imaging data.Copyright © 2006 by ASME