Search

Highlights: [•] Co-B catalyst particles were supported over three type of mesoporous silica of different pore sizes. [•] Co-B supported over SBA-15 showed highest H2 generation rate for hydrolysis of AB. [•] Confinement of Co-B within the pores creates smaller NPs (6nm) with uniform size distribution. [•] Thicker pore walls of SBA-15 avoid agglomeration of Co-B NPs at elevated temperature (873K). [Copyright &y& Elsevier]

Abstract: In addition to high catalytic efficiency the catalyst must also comprise important features like high stability in severe conditions, ability to be recycled several times and should have high tolerance against deactivation. This work is oriented specifically to study these properties of already developed efficient transition-metal doped Co–B alloy catalyst. Various transition metals, namely Ni, Fe, Cu, Cr, Mo, and W, were singly added as dopants in Co–B catalyst by chemical reduction of the corresponding metal salts. These alloy catalysts were calcinated, in Ar atmosphere, at 673, 773, and 873 K in order to investigate the stability of the powders at elevated temperatures. The catalytic performances of these treated catalyst powders were tested for H2 generation by catalytic hydrolysis of sodium borohydride (NaBH4). The alloy powders were exposed to ambient condition for several days to test their tolerance against deactivation and self life. After separation from the reaction course and after rinsing, the catalyst powders were tested for several cycles to evaluate the reusability property. The observed changes in the catalytic activity were discussed on the basis of structural and morphological variations. The Co–B catalyst, when doped with Ni, Mo, and W metals showed high stability and resistance against deterioration, as function of both time and use, as compared to Cr- and Fe-doped alloy powders. A much lower performance with respect to calcination temperature, holding time, and number of cycles was established for Cu doped Co–B catalyst powder. [Copyright &y& Elsevier]

Abstract: Co-B nanoparticles supported over carbon films were synthesized by using pulsed laser deposition (PLD) and used as catalysts in the hydrolysis of sodium borohydride (NaBH4) to produce molecular hydrogen. Amorphous Co-B-based catalyst powders, produced by chemical reduction of cobalt salts, were used as target material for nanoparticles-assembled Co-B film catalysts preparation through PLD. Various Ar pressures (10–50Pa) were used during deposition of carbon films to obtain extremely irregular and porous-carbon support with high surface area prior to Co-B film deposition. Surface morphology of the catalyst films was studied using scanning and transmission electron microscopy, while structural characterizations were carried out using X-ray diffraction. The hydrogen generation rate attained by carbon-supported Co-B catalyst film is significantly higher as compared to unsupported Co-B film and to conventional Co-B powder. Morphological analysis along with NaBH4 hydrolysis tests showed that the Co-B nanoparticles produced with PLD act as active catalytic centers for hydrolysis while the carbon support provides high initial surface area for the Co-B nanoparticles with better dispersion and tolerance against aggregation. The hydrogen generation rate obtained by the present catalyst film was also investigated as a function of Co-B loading, carbon morphology, and solution temperature. The high performance of our carbon-supported Co-B film is well supported by the obtained very low activation energy (∼31kJ (mol)−1) and exceptionally high H2 generation rate (8.1LH2 min−1 (gofcatalyst)−1) in the hydrolysis of NaBH4. [Copyright &y& Elsevier]

Abstract: Nanoparticle-assembled Co-B thin films were synthesized by Pulsed Laser Deposition (PLD) and used as catalysts for the hydrolysis of NH3BH3 (ammonia borane, AB) to produce molecular hydrogen. Amorphous Co-B-based catalyst powders, produced by chemical reduction of cobalt salts, were used as target material for Co-B thin film catalysts preparation through PLD. Surface morphology of Co-B powder and film catalyst was studied using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Compositional and structural characterizations were carried out using X-photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) techniques, respectively. The efficiency of both powder and film catalysts was tested by comparative kinetic analysis of the AB hydrolysis for hydrogen production. It was observed that nanoparticles produced during the laser ablation process act as active catalytic centers to produce significantly higher rate (about 6 times) of H2 than the same amount of the corresponding Co-B powders. Almost complete conversion (95%) of AB was obtained, as confirmed by 11B NMR, by using Co-B films at room temperature. Active Co-B nanoparticles on the surface of the PLD-deposited films is able to decrease the activation energy, for hydrolysis of AB, to the very low value of 34kJmol−1. We also found that by adding small amount of NaBH4 to the NH3BH3 solution increases the efficiency of the Co-B catalyst films, thus generating H2 with higher rate. Maximum H2 generation rate of about ∼8.2LH2 min−1 (g of Co)−1 and ∼13LH2 min−1 (g of Co)−1 was measured by hydrolysis of AB and mixture of (AB+NaBH4) solutions, respectively. [Copyright &y& Elsevier]

Abstract: Amorphous catalyst alloy powders in form of Co–P, Co–B, and Co–P–B have been synthesized by chemical reduction of cobalt salt at room temperature for catalytic hydrolysis of NaBH4. Co–P–B amorphous powder showed higher efficiency as a catalyst for hydrogen production as compared to Co–B and Co–P. The enhanced activity obtained with Co–P–B (B/P molar ratio=2.5) powder catalyst can be attributed to: large active surface area, amorphous short range structure, and synergic effects caused by B and P atoms in the catalyst. The roles of metalloids (B and P) in Co–P–B catalyst have been investigated by regulating the B/P molar ratio in the starting material. Heat-treatment at 773K in Ar atmosphere causes the decrease in hydrogen generation rate due to partial Co crystallization in Co–P–B powder. Kinetic studies on the hydrolysis reaction of NaBH4 with Co–P–B catalyst reveal that the concentrations of both NaOH and catalyst have positive effects on hydrogen generation rate. Zero order reaction kinetics is observed with respect to NaBH4 concentration with high hydride/catalyst molar ratio while first order reaction kinetics is observed at low hydride/catalyst molar ratio. Synergetic effects of B and P atoms in Co–P–B catalyst lowers the activation energy (32kJmol−1) for hydrolysis of NaBH4. The stability, reusability, and durability of Co–P–B catalyst have also been investigated and reported in this work. It has been found that by using B/P molar ratio of 2.5 in Co–P–B catalyst, highest H2 generation rate of about ∼4000mlmin−1 g−1 can be achieved. This can generate 720W for Proton Exchange Membrane Fuel Cells (0.7V): which is necessary for portable devices. [Copyright &y& Elsevier]

Nanoparticles assembled Co-B-O thin film catalysts were synthesized by pulsed laser deposition (PLD) technique for hydrolysis of Sodium Borohydride (SBH). Surface morphology of the deposited films was investigated using SEM and TEM, while compositional analysis was studied using XPS. Structural properties of Co-B-O films were examined using XRD and HRTEM. Laser process is able to produce well separated and immobilized Co-B-O NPs on the film surface which act as active centers leading to superior catalytic activity producing hydrogen at a significantly higher rate as compared to bulk powder. Co-B-O thin film catalyst produces hydrogen at a maximum rate of ∼4400 ml min −1 g −1 of catalyst, which is four times higher than powder catalyst. PLD parameters such as laser fluence and substrate-target distance were varied during deposition in order to understand the role of size and density of the immobilized Co-B-O NPs in the catalytic process. Films deposited at 3–5 cm substrate-target distance showed better performance than that deposited at 6 cm, mainly on account of the higher density of active Co-B-O NPs on the films surface. Features such as high particle density, polycrystalline nature of Co NPs and good stability against agglomeration mainly contribute towards the superior catalytic activity of Co-B-O films deposited by PLD. [ABSTRACT FROM AUTHOR]

Nanocatalysts, in the form of nanoparticles assembled coatings (NPACs) of Co 3 O 4 , were synthesized by pulsed laser deposition (PLD) with optimized parameters. Phase explosion phenomena occurring at high laser fluences produce nanoparticles (NPs) with an average size of ∼5 nm having narrow size distribution (3–10 nm) and low degree of agglomeration, which are randomly arranged in the form of coating on the substrate surface. In comparison with chemically synthesized Co 3 O 4 crystalline powder, the NPACs deposited by PLD showed significantly higher catalytic activity for H 2 generation by hydrolysis of NaBH 4 . Maximum H 2 generation rate obtained by NPACs (5010 ml min −1 g cat −1 ) is about 5 times higher than that produced by Co 3 O 4 powder (1000 ml min −1 g cat −1 ), which is mainly attributed to high surface area and large number of active sites provided by the Co 3 O 4 NPs in the coating owing to their size and shape. By varying the O 2 pressure during PLD, two different cobalt oxide phases, namely Co 3 O 4 and CoO, were formed in NPACs and found that Co 3 O 4 phase is more active for hydrolysis than CoO phase with lower oxidation number. The morphology and crystallinity of Co 3 O 4 NPACs were tuned by varying the laser fluence and substrate temperature respectively, and their effect on H 2 generation rate was studied. The results showed that the NPs with mixed amorphous-nanocrystalline phase on the surface act as active sites for favorable interaction and NaBH 4 conversion. [ABSTRACT FROM AUTHOR]