Search

Layered soil conditions are common in marine sediments, and deduction of strength properties for thin interbedded layers is often challenging. Full-flow penetrometers such as T-bar are increasingly being used in offshore site investigations and show high potential for differentiating the shear strength transition between layers. This paper reports the results from large deformation finite-element analysis undertaken to provide insight into the response of a T-bar penetrometer as it continuously penetrates through stiff–soft–stiff clay layers. The numerical results are validated against data from a centrifuge model test. Trapped soil is observed for any nonsmooth interface as the T-bar penetrates from a stiff to a softer soil layer, which affects the measured resistance of the soft layer. The effect of a cavity above the advancing T-bar was also investigated. The presence of a cavity can increase the sharpness of the transition in resistance from one layer to another, which thus affects estimation of the boundary of the soft layer. The evolution of trapped soil from the top layer within the soft layer, and then its erosion in the bottom layer, were explored. The research found that the measured resistance profile in the soft layer is sensitive to the strength ratio between the top layer and soft layer, but the resistance of the bottom layer is more reliable. Based on deduced measurement parameters from the resistance profile, a new interpretation framework is proposed for interpreting the layer boundaries and undrained shear strength of the interbedded soft layer. [ABSTRACT FROM AUTHOR]

This paper reports advances in the prediction of spudcan resistance profiles during installation and preloading, based on the soil flow mechanisms observed in model tests and numerical analysis, and taking into account strain softening and rate dependency on the soil strength. Deep penetration of spudcan foundations was simulated for 14 case histories reported from different locations in the Gulf of Mexico, where the soils were single layer, predominantly normally to lightly overconsolidated clay. Axisymmetric and three-dimensional analyses were carried out using two large deformation finite-element (LDFE) approaches, modifying the simple elastic-perfectly plastic Tresca soil model to allow strain softening and strain-rate dependency of the shear strength. The field data were compared with the results of the finite-element analyses and with predictions using various design approaches. Excellent agreement was found, particularly when a mechanism-based design approach was used that differentiated between conditions before and after backflow of soil above the penetrating spudcan. [ABSTRACT FROM AUTHOR]

Large-deformation finite-element analysis has been used to model the undrained response of skirted shallow foundations in uplift and compression. Large-deformation effects involve changes in embedment ratio and operative local soil shear strength with increasing foundation displacement--either in tension or compression. Centrifuge model testing has shown that these changes in geometry affect the mobilized bearing capacity and the kinematic mechanisms governing failure in undrained uplift and compression. Small-strain finite-element analysis cannot by definition capture the effects of changing foundation embedment ratio and variation in local soil strength with foundation displacement. In this paper, load-displacement relationships, ultimate capacities, and kinematic mechanisms governing failure from large-deformation finite-element analyses are compared with centrifuge model test results for circular skirted foundations with a range of embedment between 10 and 50% of the foundation diameter. The results show that the large-deformation finite-element method can replicate the load-displacement response of the foundations over large displacements, pre- and postyield, and also capture differences in the soil deformation patterns in uplift and compression. The findings from this study increase confidence in using advanced numerical methods for determining shallow skirted foundation behavior, particularly for load paths involving uplift. [ABSTRACT FROM AUTHOR]

One of the critical issues associated with plate anchor performance and design relates to the reduction of the loss of embedment during the keying process. As deep water offshore sediments typically exhibit an increasing soil strength with depth, the loss of embedment results in a reduction in anchor bearing capacity. A keying flap hinged to the main plate has been developed and adopted by industry with the aim to reduce the loss of embedment by limiting the vertical motion of the anchor. However, uncertainties remain regarding the behavior and the performance of the keying flap. This paper presents a series of numerical analyses performed to investigate the flap rotation mechanism and the condition of activation of the flap. They are compared with existing centrifuge modeling. The numerical results validate the centrifuge observations and demonstrate the nonactivation of the keying flap for typical anchor pull-out conditions. [ABSTRACT FROM AUTHOR]

A manually operated penetrometer (DMS) fitted with cylindrical (T-bar) and ball penetrometer tips was developed for measuring the profiles of undisturbed and remolded undrained shear strength within box-core samples. This paper summarizes the findings of a series of miniature penetrometer tests and vane shear tests that were carried out on reconstituted clay from a local site in Western Australia. The aim of the tests was to evaluate the potential of the DMS in characterizing the shear strength of seabed surficial sediments. It was found that the DMS gave essentially identical T-bar and ball penetration resistances but these were up to 17% lower than the net cone resistance. From the comparison between the T-bar and ball penetration resistance and the shear strengths measured from vane shear tests, average N factors of 11 and 14 were obtained for intact and fully remolded conditions, respectively. The test results suggest that the DMS is a reliable and efficient means of obtaining intact and remolded shear strength profiles. [ABSTRACT FROM AUTHOR]

Three-dimensional large deformation finite-element (FE) analyses were performed to investigate plate anchor capacity during vertical pullout. The remeshing and interpolation technique with small strain approach was expanded from two-dimensional to three-dimensional conditions and coupled with the FE software, ABAQUS. A modified recovery of equilibrium in patches technique was developed to map stresses after each remeshing. Continuous pullout of rectangular plate anchors was simulated and the large deformation results for strip, circular, and rectangular anchors were compared with model test data, small strain FE results, and plastic limit solutions. Interface conditions of no breakaway (bonded) and immediate breakaway (no tension) were considered at the anchor base. The effects of anchor roughness, aspect ratio, soil properties, and soil overburden pressure were investigated. It was found that the anchor roughness had minimal effect on anchor performance. For square and circular deep anchors under immediate breakaway conditions, the maximum uplift capacity increased with soil elastic modulus, which suggests that lower bound limit analysis and small strain FE analysis may overestimate the capacity. The soil beneath the anchor base separates from the anchor at a certain embedment depth near the mudline, once tensile stresses were generated. The ratio of separation depth to anchor width was found to increase linearly with the ratio of soil undrained shear strength to the product of soil effective unit weight and anchor width and was independent of the initial anchor embedment depth. [ABSTRACT FROM AUTHOR]

Vertically installed plate anchors have been investigated in this paper by numerical analysis and centrifuge modeling. In the numerical analysis, the large deformation finite-element method (remeshing and interpolation technique with small strain) was used to simulate strip plate anchor rotation. In the centrifuge model tests, transparent soils were used to observe square anchor rotation. The loss in anchor embedment during anchor keying was assessed for anchors in uniform and normally consolidated soils with anchor pullout angle varying from 30° to 90° to the horizontal. It was found that the loss in anchor embedment during anchor keying may be expressed in terms of a nondimensional anchor geometry factor, which is a function of the eccentricity of the padeye, angle of loading, and the net moment applied to the anchor at the stage where the applied load balances the anchor weight. However, once the anchor geometry factor reaches a certain value, the loss in anchor embedment stabilizes at 0.25–0.5 times the anchor width. The loss in anchor embedment decreases linearly with decreasing pullout angle. Simple formulae and design procedures have been proposed to estimate the loss in anchor embedment during keying. [ABSTRACT FROM AUTHOR]

Spudcan foundations for offshore mobile drilling rigs are large saucer-shaped foundations that can penetrate several tens of meters into soft sediments. The penetration depth is typically predicted by considering a wished-in-place foundation at different depths and following traditional bearing capacity approaches to assess the depth at which the estimated capacity matches the applied loading. However, the geometry of the spudcan and its progressive mode of penetration lead to soil failure mechanisms that differ markedly from those relevant to onshore practice. This paper presents a new rational design approach for assessing spudcan penetration in single layer clays based on a study combining centrifuge model testing and large deformation finite-element (FE) analysis. The design approach takes account of the evolving failure mechanisms in the soil, which start with cavity formation and surface heave at shallow penetration, gradually transforming to backflow of soil over the spudcan. A detailed FE parametric study has explored the relevant range of normalized strength, strength nonhomogeneity, and spudcan base roughness, with results validated against centrifuge model test data. The penetration response curves are presented in terms of profiles of bearing capacity factors, forming nondimensional design charts along with simplified expressions for convenient use in practice. Comparisons with approaches suggested in the SNAME design code suggest an urgent need to update current practice. [ABSTRACT FROM AUTHOR]

The undrained remolded shear strength of soft clays is of importance in geosystem design, particularly for offshore structures. Common methods to estimate remolded shear strength, such as correlations with cone penetration data, direct measurement with an in situ field vane shear device, and laboratory measurements, produce varied results and can be particularly costly and time consuming. Full-flow penetrometers (T-bar and Ball) provide an alternative rapid method to estimate remolded shear strength and soil sensitivity through remolding soil by repeated cycling of the penetrometer up and down over a given depth interval. The cyclic penetration resistance degradation curve inherently contains information regarding remolded strength and sensitivity. The objective of this paper is to assess the ability of full-flow penetrometers to predict remolded strength and soil sensitivity, and to develop a suite of predictive correlations in which these properties can be estimated in the absence of complementary laboratory or in situ test data. To accomplish this, full-flow penetration profiles and cyclic tests were performed at five well characterized soft clay sites, which together represent the broad range of soils in which the penetrometers will be often used. A previously developed model for the reduction in penetration resistance with cycling is modified to predict the entire degradation curve, including the remolded penetration resistance using only measurements obtained during initial penetrometer penetration and extraction. Using field vane shear strength as the reference measurement, correlations are developed to predict soil sensitivity and remolded shear strength based solely on full-flow penetrometer data, which is particularly useful in site investigation programs where site specific data are not yet available or are sparse. Finally, the usefulness of these relationships is demonstrated by implementing them for two additional soft clay sites. [ABSTRACT FROM AUTHOR]

In practice, natural soils exhibit strain-rate dependency and also soften as they are sheared and remolded. Traditional design approaches, however, have been developed based on idealized rate-independent perfectly plastic soil. This paper presents results for deep penetration of spudcan foundations in strain-softening, rate-dependent, soft clays quantifying the effects relative to results for ideal soil. The analysis was carried out using a large deformation finite-element (LDFE) approach, modifying the simple elastic-perfectly plastic Tresca soil model to allow strain softening, and incorporate strain-rate dependency of the shear strength. Parametric analyses were undertaken varying the strain-rate parameter, the sensitivity and ductility of the soil, the normalized penetration rate, and the soil strength nonhomogeneity. Overall, penetration resistance for rate-dependent, strain-softening clays lay below that for ideal soil. Increased brittleness of the soil led to marked reduction in penetration resistance, only partly compensated by strain-rate dependency. Key results have been presented in the form of design charts, fitted by simple expressions to estimate the limiting cavity depth above the advancing spudcan and the limiting bearing capacity factor at depth. [ABSTRACT FROM AUTHOR]

This paper addresses numerical simulation of deep penetration of full-flow penetrometers in strain-softening, rate-dependent, cohesive soil, and the observed phenomenon of periodic shear bands. The analysis was conducted using a large deformation finite element approach, modifying the simple elastic–perfectly plastic Tresca soil model to allow strain-softening, with strain-rate dependency being incorporated in order to avoid spurious mesh dependency. Parametric analyses were carried out varying the strain-softening parameters (hence the relative brittleness of the soil), the rigidity index of the soil, and the strain-rate parameter. Increased brittleness of the soil led to reduction in the penetration resistance, but also to increasingly significant oscillations in the resistance–penetration responses. The oscillation was found to result from periodic shear bands evolving cyclically ahead of the advancing cylindrical and spherical penetrometers. Analyses with different values of rigidity index confirmed further that the periodic shear bands were a real material phenomenon, rather than due to errors in numerical simulation. Similar phenomena have been observed for continuous flow problems in granular materials. However, rising strain-rate dependency tended to suppress the oscillations. [ABSTRACT FROM AUTHOR]

The response of piles subjected to lateral loading (along a single line of action) has been substantially investigated in the past. However, little attention has been devoted to studying how a change in the lateral load direction (say, from east–west to north–south) may affect the overall response. This paper describes a Winkler type of soil–pile interaction model that allows coupling between the two perpendicular directions in a systematic way, by adopting local yield surfaces along the pile. A parametric study is presented for a range of pile lengths and cross sections, applied loads, and changes in direction from previous loadings. An analogy is shown to exist between the response of the pile to changes in the direction of lateral loads and the well-known elementary constitutive phenomenon of the recent stress history. As is commonly assumed in practice the model shows that the direction of the resultant pile response does not have a large impact on the load carrying capacity of the system. However, changes in the lateral load directions alter the global stiffness response, and this could potentially play a significant role in the serviceability design. [ABSTRACT FROM AUTHOR]

The penetration resistance of a cylindrical T-bar penetrometer in soft clay is affected by features such as anisotropy, high strain rates, and gradual strain-softening during passage of the T-bar. In order to evaluate these effects, a detailed numerical study has been undertaken, comprising: (1) finite-element analysis; and (2) a strain path approach within the upper bound plasticity mechanism. These studies showed that the T-bar factor is relatively insensitive to the degree of strength anisotropy, provided the penetration resistance is normalized by the average shear strength. Strain rates were found to be six or seven orders of magnitude greater than typical laboratory testing rates, and about three orders of magnitude higher than in a standard vane test. However, the effect of high strain rates is partly compensated by remolding of the soil, where average strains of 400% are imposed on the soil. Charts are presented showing how the separate effects of high strain rates and partial softening may be combined to derive a T-bar factor for a given soil. The paper concludes with a discussion of the measurement of remolded shear strength using cyclic T-bar tests, and interpretation of the T-bar resistance in fully remolded soil. [ABSTRACT FROM AUTHOR]

This paper discusses the effects of penetration rate on the penetration resistance in soft clay for various shaped penetrometers (cone, T-bar, ball, and plate) and for T-bars with different aspect ratios. Constant rate (“normal”) and variable rate (“twitch”) penetration tests, where the penetration rate was successively halved over eight steps with the penetrometer advanced by one or two diameters in each step, were undertaken in the beam centrifuge at the University of Western Australia. The tests were conducted on samples reconstituted from clay collected from the Burswood site in Western Australia. The twitch tests showed higher penetration resistance than the corresponding normal tests after the penetration rate had been reduced by a factor of 16 due to cumulative effects of partial consolidation. The penetration rate at which the resistance started to increase due to partial consolidation was used to estimate the consolidation coefficient, cv, of the reconstituted clay. The interpreted cv values were similar to values estimated from other consolidation data, both in the centrifuge and from laboratory Rowe cell and constant rate of strain consolidation tests. In addition, results from in situ twitch tests at the Burswood site were examined to evaluate viscous effects on the penetration resistance. [ABSTRACT FROM AUTHOR]

This paper reports advanced three-dimensional large-deformation finite element analyses investigating the effect of the padeye offset on the behaviour of plate anchors. The analyses varied the normalized padeye offset from 0 to 0.5 and identified two counterbalancing effects on the anchor bearing capacity induced by the padeye offset. These are the change in anchor inclination with respect to the direction of loading (detrimental due to the reduction of bearing area) and the reduction of loss of embedment (beneficial, as the anchor mobilizes stronger soil). The results provide insights to optimize the design of plate anchors. The underlying concepts also have applications for other types of anchors. [ABSTRACT FROM AUTHOR]

Shallow skirted foundations can mobilize uplift resistance from end bearing in the short to medium term. However, uncertainty exists over the magnitude of reverse end bearing resistance compared with resistance in compression, and how this might be affected by a gap between the external face of the foundation skirt and the adjacent soil. The study presented in this paper explores this problem through centrifuge model tests, investigating the effect of skirt embedment ratio on ( i) the magnitude of reverse end bearing capacity compared with compression capacity, ( ii) the uplift displacement associated with spontaneous loss of suction during uplift, and ( iii) the existence of a vertical gap along the external skirt-soil interface. The results show that ( i) peak uplift capacity equivalent to compression capacity can be mobilized for a fully sealed foundation with an intact skirt-soil interface, ( ii) suction required for reverse end bearing can be maintained through considerable foundation displacement, even for a low skirt embedment ratio, and ( iii) the presence of a vertical gap along the external skirt-soil interface causes abrupt loss of suction beneath the top plate after minimal foundation displacement, with subsequent uplift capacity being markedly reduced. [ABSTRACT FROM AUTHOR]

Current site investigation practice for offshore pipeline design relies on soil parameters gathered from boreholes or in situ test soundings to depths of 1-2 m below the mudline. At these depths, the fine-grained seabed is very soft and possesses low undrained strength, which can be difficult to measure. This paper describes a centrifuge test programme undertaken to evaluate the feasibility and performance of a novel penetrometer designed to assess the shallow strength of soft seabed over continuous horizontal profiles. This device is termed the vertically oriented penetrometer (VOP). Tests were performed on a normally consolidated kaolin sample, with the VOP translated horizontally at velocities ranging from 1 to 30 mm/s, after embedding the VOP at 30 and 45 mm depths. All tests involved many cycles of VOP forward and backward movement to assess its potential to derive the ratio of intact to fully remoulded strength. Strength determination is achieved by dragging the VOP at a specified embedment depth along the soil surface, and deriving the soil strength from the measured resistance as if the VOP were a laterally loaded pile. The VOP is shown to yield comparable strength measurements to that of a T-bar penetrometer. The VOP is a potentially valuable addition to the range of tools used to characterize soil strength, both in small-scale centrifuge models and, following practical development, potentially also in the field. [ABSTRACT FROM AUTHOR]