Search

The extracted fish samples (w/w) using pressurized liquid extraction (PLE) were cleaned up by applying different adsorbent materials such as: combination of acidic/ basic silica and alumina, florisil, and silica gel either alone or in combination with another sort of sorbent. Different solvents such as hexane (H), dichloromethane (DCM), with different compositions were used to elute the PCBs target compounds from the spiked fish samples. Overall the mean percentage recoveries for all PCBs congeners using PLE were ranging from 78.6% to 98.7%; from 79.4% to 91.8%; from 65.8% to 104.5% and from 82.4% to 100.9% for cases A, B, C, D and E, respectively. However, the overall mean percentage recoveries for the 13C-PCBs surrogate including: 101, 138, 153, 180 and 209 were ranging from 88.2% to 97.6%; from 79.4% to 90.2%, from 88.3% to 96.4%, from 79.8% to 90.4% and from 83.9% to 95.9%, for cases A, B, C, D and E, respectively. The limits of detection of the proposed method were varied from 0.01 to 0.28 ng/g (w/w) for different PCBs congeners. The proposed method has linear dynamic range from 21.5 ng/g to 109 ng/g. This method was applied to fish samples for the determination of the target PCBs components.

A new GC-ion trap MS method has been developed for the determination of polycyclic aromatic hydrocarbons (PAHs) in sewage sludge samples. The sludge samples were extracted with Soxhlet, Soxtec, and pressurized liquid extraction (PLE) using 1:1 (v/v) dichloromethane (DCM):n-hexane solvent mixture. A multi-layer clean-up (silica/Al2O3) column were used, followed by gel permeation chromatography (GPC) to eliminate the interfering organic compound as well as the lipids. The extracts were quantified with GC–EI-SIS and GC–EI-MS–MS. The method was successfully applied to determine the concentration of PAHs present in sewage sludge samples collected from four waste water treatment plants (WWTPs). The method recovery values varied from 61.5 to 90.5%, 65.0 to 91.8% and 60.0 to 93.4% for Soxtec extraction, Soxhlet extraction and PLE extraction, respectively. The total concentrations of the 16 PAHs in the sewage sludge samples were found to vary from 1.56 to 6.18 mg/kg. The concentration of PAHs in WWTPs did not significantly vary.

A new analytical method is described for the determination of organochlorine pesticides (OCPs) in sewage sludges using GC-ion trap-MS-MS. In this work, 16 organo-chlorine pesticides (OCPs) listed by the US Environmental Protection Agency (US EPA) as priority pollutants were separated and quantified. Sludge samples from three of Kuwait's wastewater treatment plants (WWTPs) were analyzed for organochlorine pesticides (OCPs). Spiked sludge samples were extracted with a mixture of (1:1 v/v) dichloromethane (DCM)/hexane. The extracts were cleaned on a silica/aluminum oxide column, then transferred to a gel permeation chromatography (GPC) column, before undergoing further silica/aluminum oxide clean-up; the presence of OCPs was then confirmed by GC-ion trap-MS-MS. Three extraction techniques, soxtec, soxhlet, and pressurized liquid extractions were utilized, compared and validated using the spiked sludge samples. The methods were validated in term of accuracy (recovery) and precision (RSD). The method recovery values varied from 76.1 to 92.9% for the three extraction techniques.

Vacancy ion-exclusion/adsorption chromatography has been applied to investigate the separation behavior of five aliphatic amines (ethylamine, propylamine, butylamine, pentylamine and hexylamine) on a polymethacrylate-based weakly basic anion-exchange column (Tosoh TSKgel DEAE-5PW). This system is consisted of analytes as a mobile phase and water as an injected sample. In the vacancy ion-exclusion/adsorption chromatography, the elution order was as follows: ethylaminepropylaminebutylaminepentylaminehexylamine, depending on their hydrophobicity. The retention times of the amines were decreased with decreasing their concentrations in the mobile phase. The retention times and resolutions of the amines were increased by adding a basic compound (e.g., lithium hydroxide or heptylamine) and by increasing the pH of mobile phase (pH11). This was because the dissociations of amine samples in the mobile phase were suppressed and thus the hydrophobic adsorption effects were enhanced. The linearity of calibration graphs could be obtained from the peak areas of the amine samples injected to the 0.05, 0.5 and 5 mM of amine mobile phase at pH 11 by heptylamine. The detection limits of aliphatic amines as injected samples were around 1 microM for five aliphatic amines at three different amine mobile phases. From these results, the retention behaviors of aliphatic amines on vacancy ion-exclusion/adsorption chromatography were concluded to be governed by the hydrophobic adsorption effect.

This paper describes an ion-exclusion chromatographic system for the rapid and selective determination of ammonium ion. The optimized ion-exclusion chromatographic system was established with a polymethacrylate-based weakly basic anion-exchange resin column (TSKgel DEAE-5PW) as the separation column, an aqueous solution containing 0.05 mM tetramethylammonium hydroxide (pH 9.10) as eluent with conductimetric detection for the analyte determination. Under the optimum chromatographic conditions, ammonium ion was determined within 2.3 min with a detection limit (S/N=3) better than 0.125 microM. Ammonium ion in rain and river waters was precisely determined using this ion-exclusion chromatographic system.

In this study, an aqueous solution consisting of benzoic acid with low background conductivity and beta-cyclodextrin (beta-CD) of hydrophilic nature and the inclusion effect to benzoic acid were used as eluent for the ion-exclusion chromatographic separation of aliphatic carboxylic acids with different pKa values and hydrophobicity on a polymethacrylate-based weakly acidic cation-exchange resin in the H+ form. With increasing concentration of beta-cyclodextrin in the eluent, the retention times of the carboxylic acids decreased due to the increased hydrophilicity of the polymethacrylate-based cation-exchange resin surface from the adsorption of OH groups of beta-cyclodextrin. Moreover, the eluent background conductivity decreased with increasing concentration of beta-cyclodextrin in 1 mM benzoic acid, which could result in higher sensitivity for conductimetric detection. The ion-exclusion chromatographic separation of carboxylic acids with high resolution and sensitivity was accomplished successfully by elution with a 1 mM benzoic acid-10 mM cyclodextrin solution without chemical suppression.

A monolithic ODS-silica gel column modified by saturating it with lithium dodecylsulfate (Li-DS) was used to demonstrate the high-speed separation of H+ from other mono- and divalent cations, such as Na+, NH4+, K+, Mg2+ and Ca2+ using ion chromatography (IC). Using a 5 mM EDTA-2K solution containing 0.10 mM Li-DS (pH 4.80) as eluent, H+ was eluted with a sharp and symmetrical peak within 1.0 min before other cations at a flow-rate of 1.5 ml min(-1). The rapid elution of H+ and its conductimetric detection could be attributed to the presence of EDTA (HY2-), which can convert H+ ions as anions. i.e. H(+) + H2Y(2-) --> H3Y(-). The acidity of rainwater and deionized water samples was determined using this IC system with satisfactory results.

A monolithic ODS-silica gel column modified by saturating it with lithium dodecylsulfate (Li-DS) was firstly used to separate monovalent cations simultaneously including H+, Na+, NH4+ and K+ by ion-chromatography (IC). Using an acidified 60 mM LiCl solution (pH 3.95, containing 0.10 mM Li-DS) as eluent, these monovalent cations were separated well in the order of Na+

A new approach to ion-exclusion chromatography (IEC) is proposed to overcome the relatively poor conductivity detection response which occurs in IEC on when acids are added to the eluent in order to improve peak shape. This approach, termed vacancy IEC, requires the sample to be used as mobile phase and a sample of water to be injected onto a polystyrene/divinylbenzene (PS/DVB)-based strongly acidic cation-exchange column (TSKgel SCX). Vacancy peaks for each of the analytes appear at the retention times of these analytes. Highly sensitive conductivity detection is possible and sharp, well-shaped peaks are produced, leading to efficient separations. Retention times were found to be affected by the concentration of the analytes in the eluent, and also by the presence of an organic modifier, such as butanol in the mobile phase. Detection limits for oxalic, formic, acetic, propionic, butyric and valeric acids at S/N=3 were 0.04, 0.1, 0.47, 0.66, 0.71 and 0.82 μM, respectively, and linear ranges for some acids extended over two-orders of magnitude. Precision values for retention times were

The simultaneous determination of endocrine disruptors (phenols) has been developed using a GC–MS method. Endocrine disruptors in various water samples, were extracted using a liquid–liquid extraction process. Acidification pH 2.0–3.0 and salting (NaBr) of water samples really enhance the extraction process. The extraction of endocrine disruptors was done and experimented twice with 50 ml of “dichloromethane”. The volume was concentrated from 100 to 1 ml. Internal standard of anthracene was also added to the concentrated volumes followed by derivatization with N,O -bis(trimethylsilyl)trifluoroacetamide (BSTFA) to form phenol-trimethylsilylate (phenol-TMS) derivative. The phenol-TMS derivative was analyzed by GC–MS method. The applied concentrated range was over 10–1000 ng/ml for the total phenols. The recovery test ranged from 59.5 to 88.6% with relative standard deviations between 1.6 and 10.3% of 500 ng/ml of the standard phenols spiked to the water sample and the detection limit was 1 ng/ml. The proposed method was applied satisfactory to the determination of total endocrine disruptors in synthetic mixtures and different types of water sample, such as river, tap and distilled waters, previously spiked with different amounts of these chemicals.

A new, simple, sensitive, selective and in-field fluorimetric method for the determination of formaldehyde is proposed. The reaction of formaldehyde with hydralazine in acidic medium, heating on a boiling water-bath for 25 min, produces s-triazolo[3,4-a]phthalazine (Tri-P). The fluorescence intensity of the product formed (Tri-P) was determined at λem = 389 nm with λex = 236 nm. The fluorescence intensity is linear over a formaldehyde concentration range of 1.2–33.0 μg l−1. The proposed method was applied successfully to the determination of formaldehyde sampled from the atmosphere using the liquid droplet technique. Formaldehyde vapour in a wind tunnel was produced by a mean of permeater. A linear curve was obtained between the concentration in the wind tunnel and that in the droplet. The detection limit for formaldehyde was 2.0 μg l−1 with RSDs varying from 3 to 12% in ambient air, using a droplet correction solution (boric acid and hydralazine). The effect of interfering substances on the determination shows that most cations and anions did not interfere. The results obtained were satisfactory compared with a reference method.

A simple, sensitive and selective fluorometric method for the determination of nitrite is described. The fluorometric determination is based on the reaction of acetaminophen with nitrite in an acidic medium followed by alkalinization of the reaction which yields a highly fluorescent product, exhibit (λ ex /λ em =325/430 nm). The optimum experimental conditions were studied. The fluorescene intensity is linear over a nitrite concentration of 0.08–1.3 μg/ml with a detection limit of 2.7 ng/ml (S/N=3). The effect of interferences from various metals/ions were studied. The proposed method is accurate, reproducible, shows satisfactory results and compares successfully with the reference method.

A new simple and accurate kinetic method for the analysis of paracetamol in pure form and formulations is described. The kinetics parameters have been applied successfully in determining paracetamol when it reacts with persulfate in alkaline medium. The spectrophotometric measurements have been recorded at 315 nm and found to be valid over the concentration range of 5–30 ppm. The molar absorptivity is equal to 6.55×103 l mol−1 cm−1. The analysis of paracetamol content in mixture of different substances has been carried out without prior separation. The precision and accuracy of the method and the effect of foreign substances have been studied and the results obtained were compared with reference method.

A simple selective kinetic method for the assay of nalidixic acid in solid state and pharmaceutical preparations is described. The reaction of nalidixic acid with persulfate in alkaline medium was carried out at 75°C. The correlation coefficient was found to be 1.0000. The activation parameters and the factor of the linear least square equation were calculated. The proposed method is suitable to determine nalidixic acid in the range 10–120 μg/ml.

A new, simple, and sensitive kinetic spectrophotometric method is described for analysis of cefadroxil by measurement of its absorbance at 470 nm after hydrolysis with NaOH at 80°C. Studies of the method's precision and accuracy gave a standard deviation of 0.44 μg/mL and a relative standard deviation of 1.93%. The method determines cefadroxil over the concentration range 10- 100 ug/mL. Calculated activation parameters were 12.42, 25.54, 26.25, and 69.00 Kcal/mole for AE*, AG*, Ahf, and AS*, respectively. Cefadroxil concentrations can be determined from the regression line equation y = 0.627x- 8.14 x 10"5, with a correlation coefficient of

An indirect spectrophotometric method for the determination of benzylpenicillin and cloxacillin is based on extraction of iodine produced by reduction of potassium iodate in acidic medium, where hydrolytic cleavage of a β-lactam is achieved with sodium hydroxide. Beer's law is obeyed within the concentration ranges 0.04–0.8 mg ml−1 benzylpenicillin and 0.02–0.5 mg ml−1 cloxacillin. The precision, accuracy of the method and the effect of foreign substances were studied. The results have been statistically compared with those using the ammonium vanadate method. An oxidation mechanism is proposed.

An accurate and simple quantitative method for determining levodopa and methyldopa is proposed. Cerium(IV) has been successively used to react with drugs in 2M H2SO4†at 80°C. The absorbance of colored products was measured at 510 and 550nm for levodopa and methyldopa, respectively. The method has been extended to the determination of these drugs in dosage forms. The results have been statistically compared with those obtained by the reference method.

An automated pressurized liquid extraction (PLE) method followed by Power Prep™ clean-up was developed for organochlorinated pesticide (OCP) and polychlorinated biphenyl (PCB) analysis in environmental marine samples of fish, squid, bivalves, shells, octopus and shrimp. OCPs and PCBs were simultaneously determined in a single chromatographic run using gas chromatography-mass spectrometry-negative chemical ionization (GC-MS-NCI). About 5 g of each biological marine sample was mixed with anhydrous sodium sulphate and placed in the extraction cell of the PLE system. PLE is controlled by means of a PC using DMS 6000 software. Purification of the extract was accomplished using automated Power Prep™ clean-up with a pre-packed disposable silica column (6 g) supplied by Fluid Management Systems (FMS). All OCPs and PCBs were eluted from the silica column using two types of solvent: 80 mL of hexane and a 50 mL mixture of hexane and dichloromethane (1:1). A wide variety of fish and shellfish were collected from the fish market and analyzed using this method. The total PCB concentrations were 2.53, 0.25, 0.24, 0.24, 0.17 and 1.38 ng g(-1) (w/w) for fish, squid, bivalves, shells, octopus and shrimp, respectively, and the corresponding total OCP concentrations were 30.47, 2.86, 0.92, 10.72, 5.13 and 18.39 ng g(-1) (w/w). Lipids were removed using an SX-3 Bio-Beads gel permeation chromatography (GPC) column. Analytical criteria such as recovery, reproducibility and repeatability were evaluated through a range of biological matrices.

A spectrophotometric determination of trimethoprim is described based on the reaction of its amine group with persulfate which acts as a strong oxidizing agent in alkaline media. The reaction produces a stable yellow colored compound after heating in a boiling water bath for 30 min. At λmax 355 nm, Beer’s law is obeyed in the concentration range 10–60 μg ml–1 with a molar absorptivity of 2.7 × 103 l mol–1cm–1. The method is applied to formulations with sulfamethoxazole.

Vacancy ion-exclusion chromatography (VIEC) for inorganic acids such as H 2 SO 4 , HCl, H 3 PO 4 , HNO 3 , HI and HF is tested on a polymethacrylate-based weakly acidic cation-exchange resin column in the H + -form. That is, mixture of inorganic acids in the mobile phase is adsorbed to the resin phase passing through the separation column, and each vacant peak induced by injecting water is determined. Retention times are dependent on the degrees of retention for each analyte in the resin phase. In VIEC, well-shaped peaks of inorganic acids are produced, leading to efficient separations. However, retention behaviors of inorganic acids were strongly affected by the concentrations of the acids in the mobile phase. Sulfosalicylic acid was mixed with inorganic acids in the mobile phase prior to the introduction of a separation column in order to obtain the well-resolutions in the lower concentrations of the acids. By using this method, the separations of inorganic acids could be achieved in the range of 0.01–1 mM, and the linear ranges could be extended over two-orders of magnitude. This is considered since the protonated carboxylic groups fixed on the resin phase were increased with increasing the acid concentrations in the mobile phase, and the penetration effects for the acids to the resin phase were thus enhanced. The detection limits (S/N = 3) were below 1.0 μM for all analyte acids. Precision values for retention times were below 0.32% and for peak area were below 0.91%.

The high-speed ion-exclusion chromatographic determination of dissolved carbon dioxide, i.e., carbonic acid, hydrogencarbonate or carbonate, with conductivity detection was obtained using a small column packed with a weakly acidic cation-exchange resin in the H+-form (40 mm long x 4.6 mm i.d., 3 microm-particle and 0.1 meq./ml-capacity). Two different ion-exchange resin columns, which were a strongly acidic cation-exchange resin in the K+-form and a strongly basic anion-exchange resin in the OH- -form, were connected after the separation column. The sequence of columns could convert dissolved carbon dioxide to KOH having high conductivity response. The enhancement effect for dissolved carbon dioxide could retain even on the vast chromatographic runs, by using the enhancement columns with high ion-exchange capacity above 1.0 meq./ml. The retention time was in 60 s at flow-rate of 1.2 ml/min. The calibration graph of dissolved carbon dioxide estimated as H2CO3- was linear in the range of 0.005-10 mM. The detection limit at signal to noise of 3 was 0.15 microM as H2CO3-. This method was applicable to several rainwater and tap water samples.

The simultaneous ion-exclusion/cation-exchange separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin of 3 microm particle size was used to achieve the simultaneous high-speed separation of anions and cations (Cl(-), NO3(-), SO4(2-), Na(+), K(+), NH4(+), Ca(2+) and Mg(2+)) commonly found in environmental samples. The high-speed simultaneous separation is based on a combination of the ion-exclusion mechanism for the anions and the cation-exchange mechanism for cations. The complete separation of the anions and cations was achieved in 5 min by elution with 15 mM tartaric acid-2.5 mM 18-crown-6 at a flow-rate of 1.5 ml/min. Detection limits at S/N=3 ranged from 0.36 to 0.68 microM for anions and 0.63-0.99 microM for cations. This method has been applied to the simultaneous determination of anions and cations in several environmental waters with satisfactory results.

A simple, selective and sensitive method for the determination of carboxylic acids has been developed. A mixture of formic, acetic, propionic, valeric, isovaleric, isobutyric, and isocaproic acids has been separated on a polymethacrylate-based weak acidic cation-exchange resin (TSK gel OA pak-A) based on an ion-exclusion chromatographic mechanism with detection using UV-photodiode array, conductivity and atmospheric pressure chemical ionization mass spectrometry (APCI-MS). A mobile phase consisting of 0.85 mM benzoic acid in 10% aqueous methanol (pH 3.89) was used to separate the above carboxylic acids in about 40 min. For LC-MS, the APCI interface was used in the negative ionization mode. Linear plots of peak area versus concentration were obtained over the range 1-30 mM (r2=0.9982) and 1-30 mM (r2=0.9958) for conductimetric and MS detection, respectively. The detection limits of the target carboxylic acids calculated at S/N=3 ranged from 0.078 to 2.3 microM for conductimetric and photometric detection and from 0.66 to 3.82 microM for ion-exclusion chromatography-APCI-MS. The reproducibility of retention times was 0.12-0.16% relative standard deviation for ion-exclusion chromatography and 1.21-2.5% for ion-exclusion chromatography-APCI-MS. The method was applied to the determination of carboxylic acids in red wine, white wine, apple vinegar, and Japanese rice wine.

In this preliminary study, a new approach to ion-exclusion chromatography is proposed to overcome the relatively poor conductivity detection response which occurs in ion-exclusion chromatography when acids are added to the eluent in order to improve peak shape. This approach, termed vacancy ion-exclusion chromatography, requires the sample to be used as eluent and a sample of water to be injected onto a weakly acidic cation-exchange column (TSKgel OApak-A). Vacancy peaks for each of the analytes appear at the retention times of these analytes. Highly sensitive conductivity detection is possible and sharp, well-shaped peaks are produced, leading to efficient separations. Retention times were found to be affected by the concentration of the analytes in the eluent, and also by the presence of an organic modifier such as methanol in the eluent. Detection limits for oxalic, formic, acetic, propionic, butyric and valeric acids were 0.1, 0.2, 0.3, 0.3, 0.4 and 0.5 microM, respectively, and linear ranges for some acids extended over two orders of magnitude. Precision values for retention times were 0.21% and for peak areas were1.90%. The vacancy ion-exclusion chromatography method was found to give detection responses four to 10 times higher than conventional ion-exclusion chromatography using sulfuric acid eluent and two to five times higher than conventional ion-exclusion chromatography using benzoic acid eluent.

A simple, rapid, accurate and sensitive method is proposed for the simultaneous determination of nitrite and nitrate in human saliva. Nitrite and nitrate present in the human saliva were determined after 10- to 100-fold dilution with ion chromatography (IC) using suppressed conductivity detection. Recoveries of nitrite and nitrate were found to be ranged between 95% and 101%. The method was linear (r2=0.9991) over the concentration working range. The detection limits were found to be 15.0 microg/l and 33.5 microg/l, for nitrite and nitrate, respectively. Ions that are present in human saliva and several other ions that are suspected to affect nitrite and nitrate determination were checked. It was found that most of the ions did not cause any interference in the determination. The method allows simultaneous determination of nitrite and nitrate in human saliva.

An accurate and precise analytical method for the determination of polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), and organo-chlorinated pesticides (OCPs) in fish and shellfish based on automated pressurized liquid extraction (PLE) and automated power-prep™ clean-up has been developed. After extraction, the extract was passed through gel permeation chromatography (GPC) using 12 g of Bio-beads SX-3 for fat removal. GC/MS (NCI) was selected for OCPs and PCBs due to its high sensitivity and selectivity of NCI to chlorinated compounds and GC/MS (EI) for PAHs. The method was validated using spiked surrogates of 13C-PCBs, deuterated PAH (d-PAHs) and fish reference material (EDF-2525). All of the recoveries are within the acceptance levels and in accordance with the US-EPA standard methods. The calibration ranges for most of the compounds were from 50 to 1000 ng ml−1 for PAHs, 10 to 103 ng ml−1 for PCBs and 10 to 200 ng ml−1 for OCPs. The limits of detection ranged between 0.01 and 0.28 ng g−1 (w/w) for PCBs, 0.03–2.48 ng g−1 (w/w) for OCPs and 0.1 to 1.0 ng g−1 (w/w) for PAHs. Analytical criteria, such as repeatability and reproducibility were evaluated through a range of biological matrices and fish reference material analysis. The feasibility of extraction using a power-prep™/PLE system combined with power-prep™ automated clean-up demonstrated a validated method for the analysis of biota samples.

A simple, fast and sensitive titrimetric method has been developed for the determination of tetracycline hydrochloride in human urine using m-dinitrobenzene as color agent and Dowex 1 × 8 as detection medium.