Search

Nanoparticle catalyst materials are becoming ever more important in a sustainable future. Specifically, platinum (Pt) nanoparticles have relevance in catalysis, in particular, fuel cell technologies. Sputter deposition into liquid substrates has been shown to produce nanoparticles without the presence of air and other contaminants and the need for precursors. Here, we produce Pt nanoparticles in three imidazolium-based ionic liquids and PEG 600. All Pt nanoparticles are crystalline and around 2 nm in diameter. We show that while temperature has an effect on particle size for Pt, it is not as great as for other materials. Sputtering power, time, and postheat treatment all show slight influence on the particle size, indicating the importance of temperature during sputtering. The temperature of the liquid substrate is measured and reaches over 150 °C during deposition which is found to increase the particle size by less than 20%, which is small compared to the effect of temperature on Au nanoparticles presented in the literature. High temperatures during Pt sputtering are beneficial for increasing Pt nanoparticle size beyond 2 nm. Better temperature control would allow for more control over the particle size in the future.

Semiconductor heterostructure junctions are known to improve the water oxidation performance in photoelectrochemical (PEC) cells. Depending on the semiconductor materials involved, different kinds of junctions can appear, for instance, type II band alignment where the conduction and valence bands of the semiconductor materials are staggered with respect to each other. This band alignment allows for a charge separation of the photogenerated electron-hole pairs, where the holes will go from low-to-high valance band levels and vice versa for the electrons. For this reason, interface engineering has attracted intensive attention in recent years. In this work, a simplified model of the Fe2O3-TiO2 heterostructure was investigated via first-principles calculations. The results show that Fe2O3-TiO2 produces a type I band alignment in the heterojunction, which is detrimental to the water oxidation reaction. However, the results also show that interstitial hydrogens are energetically allowed in TiO2 and that they introduce states above the valance band, which can assist in the transfer of holes through the TiO2 layer. In response, well-defined planar Fe2O3-TiO2 heterostructures were manufactured, and measurements confirm the formation of a type I band alignment in the case of Fe2O3-TiO2, with very low photocurrent density as a result. However, once TiO2 was subjected to hydrogen treatment, there was a nine times higher photocurrent density at 1.50 V vs. the reversible hydrogen electrode under 1 sun illumination as compared to the original heterostructured photoanode. Via optical absorption, XPS analysis, and (photo)electrochemical measurements, it is clear that hydrogen treated TiO2 results in a type II band alignment in the Fe2O3-H:TiO2 heterostructure. This work is an example of how hydrogen doping in TiO2 can tailor the band alignment in TiO2-Fe2O3 heterostructures. As such, it provides valuable insights for the further development of similar material combinations.

Currently, platinum is the most widely used catalyst for low temperature proton exchange membrane fuel cells (PEMFC). However, the kinetics at the cathode are slow, and the price of platinum is high. To improve oxygen reduction reaction (ORR) kinetics at the cathode, platinum can be alloyed with rare earth elements, such as yttrium. We report that Pt3Y has the potential to be over 2 times more active for the ORR compared with Pt inside a real fuel cell. We present detailed photoemission analysis into the nature of the sputtered catalyst surface, using synchrotron radiation photoelectron spectroscopy (SRPES) to examine if surface adsorbates or impurities are present and can be removed. Pretreatment removes most of the yttrium oxide in the surface leaving behind a Pt overlayer which is only a few monolayers thick. Evidence of a substochiometric oxide peak in the Y 3d core level is presented, this oxide extends into the surface even after Ar+ sputter cleaning in-situ. This information will aid the development of new highly active nanocatalysts for employment in real fuel cell electrodes.

Platinum is the most widely used and best performing sole element for catalyzing the oxygen reduction reaction (ORR) in low-temperature fuel cells. Although recyclable, there is a need to reduce the amount used in current fuel cells for their extensive uptake in society. Alloying platinum with rare-earth elements such as yttrium can provide an increase in activity of more than seven times, reducing the amount of platinum and the total amount of catalyst material required for the ORR. As yttrium is easily oxidized, exposure of the Pt-Y catalyst layer to air causes the formation of an oxide layer that can be removed during acid treatment, leaving behind a highly active pure platinum overlayer. This paper presents an investigation of the overlayer composition and quality of Pt3Y films sputtered from an alloy target. The Pt3Y catalyst surface is investigated using synchrotron radiation X-ray photoelectron spectroscopy before and after acid treatment. A new substoichiometric oxide component is identified. The oxide layer extends into the alloy surface, and although it is not completely removed with acid treatment, the catalyst still achieves the expected high ORR activity. Other surface-sensitive techniques show that the sputtered films are smooth and bulk X-ray diffraction reveals many defects and high microstrain. Nevertheless, sputtered Pt3Y exhibits a very high activity regardless of the film's oxide content and imperfections, highlighting Pt3Y as a promising catalyst. The obtained results will help to support its integration into fuel cell systems.

Mercury in aqueous streams poses severe health and environmental concerns and requires improved techniques for decontamination. One such technique is electrochemical alloy formation on platinum, which can effectively decontaminate mercury-containing aqueous streams at concentrations relevant for both industrial and natural waters. This study examines the viability of copper as an alternative to platinum. Mercury removal is faster on copper and works both with and without an applied cathodic potential. Without it, however, copper dissolution becomes a problem. Copper dissolution is preventable in neutral pH and in sulfuric acid solutions under potential control, and dissolved copper ions can be plated back onto the electrode. In the presence of nitrate or chloride anions, copper electrodes degrade rapidly even under potential control. Thus, there are practical restrictions for mercury decontamination via electrochemical alloy formation on copper, but it can be applied to solutions where copper is stable under potential control.

Retrieval of mercury from aqueous streams has significant environmental and societal importance due to its very high toxicity and mobility. We present here a method to retrieve mercury from aqueous feeds via electrochemical alloy formation on thin platinum films. This application is a green and effective alternative to traditional chemical decontamination techniques. Under applied potential, mercury ions in solution form a stable PtHg4 alloy with platinum on the cathode. A 100 nanometres platinum film was fully converted to a 750 nanometres thick layer of PtHg4. The overall removal capacity is very high, > 88 g mercury per cm3. The electrodes can easily be regenerated after use. Efficient and selective decontamination is possible in a wide pH range, allowing processing of industrial, municipal, and natural waters. The method is suited for both high and low concentrations of mercury and can reduce mercury levels far below the limits allowed in drinking water., Removal of anthropogenic mercury from water streams is of great importance given its high toxicity and ability to spread rapidly. Here, the authors demonstrate the direct alloying of mercury with a fully recyclable platinum electrode, providing effective removal at different concentrations and pH, and in the presence of other contaminants.

Solar energy induced water splitting in photoelectrochemical (PEC) cells is one of the most sustainable ways of hydrogen production. The challenge is to develop corrosion resistant and chemically stable semiconductors that absorb sunlight in the visible region and, at the same time, have the band edges matching with the redox level of water. In this work, hematite (α-Fe2O3) thin films were prepared onto an indium-doped tin oxide (ITO; In:SnO2) substrate by e-beam evaporation of Fe, followed by air annealing at two different temperatures: 350 and 500 °C. The samples annealed at 500 °C show an in situ diffusion of indium from the ITO substrate to the surface of α-Fe2O3, where it acts as a dopant and enhances the photoelectrochemical properties of hematite. Structural, optical, chemical and photoelectrochemical analysis reveal that the diffusion of In at 500 °C enhances the optical absorption, increases the electrode–electrolyte contact area by changing the surface topology, improves the carrier concentration and shifts the flat band potential in the cathodic direction. Further enhancement in photocurrent density was observed by ex situ diffusion of Ti, deposited in the form of nanodisks, from the top surface to the bulk. The in situ In diffused α-Fe2O3 photoanode exhibits an improved photoelectrochemical performance, with a photocurrent density of 145 μA cm−2 at 1.23 VRHE, compared to 37 μA cm−2 for the photoanode prepared at 350 °C; it also decreases the photocurrent onset potential from 1.13 V to 1.09 V. However, the In/Ti co-doped sample exhibits an even higher photocurrent density of 290 μA cm−2 at 1.23 VRHE and the photocurrent onset potential decreases to 0.93 VRHE, which is attributed to the additional doping and to the surface becoming more favorable to charge separation.

Fuel cells are foreseen to have an important role in sustainable energy systems, provided that catalysts with higher activity and stability are developed. In this study, highly active sputtered thin films of platinum alloyed with yttrium (Pt 3 Y) are deposited on commercial gas diffusion layers and their performance in a proton exchange membrane fuel cell is measured. After acid pretreatment, the alloy is found to have up to 2.5 times higher specific activity than pure platinum. The performance of Pt 3 Y is much higher than that of pure Pt, even if all of the alloying element was leached out from parts of the thin metal film on the porous support. This indicates that an even higher performance is expected if the structure of the Pt 3 Y catalyst or the support could be further improved. The results show that platinum alloyed with rare earth metals can be used as highly active cathode catalyst materials, and significantly reduce the amount of platinum needed, in real fuel cells.

Alloying platinum is an approach to increase the oxygen reduction reaction (ORR) activity and at the same time reduce the amount of precious platinum catalyst in proton exchange membrane fuel cells (PEMFC). In this work the cathode activity of thin films of rare earth metals (REM) alloys, Pt3Y, Pt5Gd and Pt5Tb, produced by sputter deposition onto gas diffusion layers, are evaluated in a fuel cell by means of polarization curves in O2/H2, and cyclic- and CO-stripping voltammetry in N2/5% H2. Prior to evaluation, the model electrodes were acid-treated to obtain a Pt skin covering the PtREM alloy bulk, as was revealed by energy-dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS). The core shell alloys of Pt3Y and Pt5Gd catalysts show a specific activity enhancement at 0.9 V of 2.5 times compared to pure Pt. The slightly lower enhancement factor of 2.0 for Pt5Tb is concluded to be due to leaching of the REM, that resulted in a thicker, and subsequently less strained, Pt overlayer. The high activity, combined with the minor changes in surface composition, achieved in the fuel cell environment shows that PtREM core shell catalysts are promising for the cathode reaction in PEMFC.

The water oxidation capability of the promising photoanode bismuth vanadate (BiVO4) is hampered by poor bulk electron transport and by high rates of charge recombination at the semiconductor/electrolyte interface. Here, we demonstrate that a dual modification of BiVO4 by: (i) annealing in a hydrogen-containing environment and (ii) coating with FeOOH overlayer substantially enhances the water oxidation ability of BiVO4 photoanodes. Hydrogen treated, FeOOH coated BiVO4 photoanodes exhibit a water oxidation photocurrent density of 2.16 mA cm−2 at 1.23 VRHE, which is 5 times higher than for untreated BiVO4 films. Moreover, they showed an impressive low photocurrent onset potential of −0.11 VRHE. A stable photocurrent was observed for 1 h of water oxidation measurement at 1.23 VRHE under 1 Sun illumination. The enhanced photocurrent of FeOOH/H:BiVO4 photoanode is ascribed to an improved bulk charge transport, as confirmed by impedance spectroscopy measurements and Mott-Schottky analysis. The cathodic shift of the onset potential originates from a lowering of the flat band potential and from an improvement of the charge transport at the semiconductor/electrolyte interface. The dual modification strategy used here offers a simple but effective approach of improving the water oxidation performance of BiVO4.

Hematite is a promising photoanode candidate with many favorable material properties, such as stability and suitable band-gap. However, there are some severe challenges, including high losses due to charge recombination and slow oxidation kinetics, which can be addressed by doping and addition of co-catalysts. Here, the effects of temperature driven diffusion of substrate impurities (doping) and subsequent surface modification by metal oxy-hydroxides (co-catalysts) have been studied for enhanced water-oxidation performance in photoelectrochemical (PEC) measurements. Diffusion of indium and tin from the indium-doped tin oxide (ITO) substrate into planar films of α-Fe2O3 photoanodes results in a photocurrent density (Jph) of 0.09 mA/cm2, corresponding to an approximate 9-fold enhancement over the control pristine α-Fe2O3 (0.01 mA/cm2) at 1.23 VRHE. A thin amorphous FeOOH coating over the In/Sn co-doped α-Fe2O3 photoanode improves the water oxidation performance further, with a 211 % enhancement in Jph at 1.23 VRHE and a 0.21 V cathodic shift in onset potential. Thin layers of NiOOH and FeNiOOH co-catalysts exhibit 100 and 155 % enhancement in Jph, respectively. Characterization and electrochemical measurements reveal that the enhanced performance is a result of reduced bulk recombination by temperature driven In/Sn substrate impurity doping and improved surface oxidation kinetics by the metal oxy-hydroxide overlayer. Especially deposition of FeOOH onto In/Sn co-doped α-Fe2O3 significantly reduces resistance at the semiconductor/electrolyte interface, leading to the shift in onset potential. Further, the results indicate that all the samples exhibit a quantitative correlation between the cathodic shift in photocurrent onset potential (Vonset) and flat band potential (Vfb).

We present a comprehensive study of internal quality factors in superconducting stub-geometry three-dimensional cavities made of aluminum. We use wet etching, annealing, and electrochemical polishing to improve the as machined quality factor. We find that the dominant loss channel is split between the two-level system loss and an unknown source with a 40:60 proportion. A total of 17 cavities of different purity, resonance frequency, and size were studied. Our treatment results in reproducible cavities, with 10 of them showing internal quality factors above 80 x 10(6) at a power corresponding to an average of a single photon in the cavity. The best cavity has an internal quality factor of 115 x 10(6) at a single photon level. (C) 2020 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) license (http:// creativecommons.org/licenses/by/4.0/).

The oxygen evolution reaction on hydroxyl- and oxygen-terminated hematite was investigated using first-principle calculations within a theoretical electrochemical framework. Both pristine hematite and hematite containing oxygen vacancies were considered. The onset potential was determined to be 1.79 V and 2.09 V vs. the reversible hydrogen electrode (RHE) for the pristine hydroxyl- and oxygen-terminated hematite, respectively. The presence of oxygen vacancies in the hematite surface resulted in pronounced shifts of the onset potential to 3.09 V and 1.83 V. respectively. Electrochemical oxidation measurements conducted on thin-film hematite anodes, resulted in a measured onset potential of 1.66 V vs. RHE. Furthermore, the threshold potential between the hydroxyl- and oxygen-terminated hematite was determined as a function of pH. The results indicate that electrochemical water oxidation on hematite occurs on the oxygen-terminated hematite, containing oxygen vacancies.

Increasing the stability and lifetime of the electrodes is one of the most important factors in order to realise a large scale use of polymer electrolyte membrane fuel cells (PEMFC). By using well-defined thin-film model electrodes, the stability of Pt and Pt on Ir were examined as cathode catalysts in a single cell PEMFC setup. The electrodes were fabricated by evaporating thin layers of Pt and Pt on Ir onto the microporous layer of a gas diffusion layer. The amount of Pt deposited was equivalent to 3 nm (about 6.3 mu g cm(-2)) and the amount of Ir was varied between 1.5 nm and 20 nm (between 3.4 mu g cm(-2) and 45.3 mu g cm(-2)). All samples with Ir showed an increased stability over samples with sole Pt during cyclic corrosion test between 0.6V and 1.2V vs. the reversible hydrogen electrode. For thin layers of Ir, the initial activity for the oxygen reduction reaction was equal to or superior to that of sole Pt but for thicker Ir films it was somewhat lower. Hydrogen underpotential deposition and CO stripping were used to estimate the electrochemical surface area during the experiments and physical characterisation using scanning electron microscopy and X-ray photoelectron spectroscopy were used to determine the structure of the samples. The results suggest that Ir can stabilise Pt in the cathode electrode. (C) 2013 Elsevier Ltd. All rights reserved.

Structural design on the atomic level can provide novel chemistries of hybrid MAX phases and their MXenes. Herein, density functional theory is used to predict phase stability of quaternary i-MAX phases with in-plane chemical order and a general chemistry (W 2/3 M 2 1/3 ) 2 AC, where M 2 = Sc, Y (W), and A = Al, Si, Ga, Ge, In, and Sn. Of over 18 compositions probed, only two—with a monoclinic C2/c structure—are predicted to be stable: (W 2/3 Sc 1/3 ) 2 AlC and (W 2/3 Y 1/3 ) 2 AlC and indeed found to exist. Selectively etching the Al and Sc/Y atoms from these 3D laminates results in W 1.33 C-based MXene sheets with ordered metal divacancies. Using electrochemical experiments, this MXene is shown to be a new, promising catalyst for the hydrogen evolution reaction. The addition of yet one more element, W, to the stable of M elements known to form MAX phases, and the synthesis of a pure W-based MXene establishes that the etching of i-MAX phases is a fruitful path for creating new MXene chemistries that has hitherto been not possible, a fact that perforce increases the potential of tuning MXene properties for myriad applications.

The role of mesoscopic mass transport and re-adsorption effects in electrocatalytic reactions was investigated using the oxygen reduction reaction (ORR) as an example. The electrochemical measurements were performed on structurally well-defined nanostructured model electrodes under controlled transport conditions in a thin-layer flow cell. The electrodes consist of arrays of Pt ultra-microelectrodes (nanodisks) of defined size (diameter approximately 100 nm) separated on a planar glassy carbon (GC) substrate, which were fabricated employing hole-mask colloidal lithography (HCL). The measurements reveal a distinct variation in the ORR selectivity with Pt nanodisk density and with increasing electrolyte flow, showing a pronounced increase of the H2O2 yield, by up to 65%, when increasing the flow rate from 1 to 30 microL s(-1). These results are compared with previous findings and discussed in terms of a reaction model proposed recently (A. Schneider et al., Phys. Chem. Chem. Phys., 2008, 10, 1931), which includes (i) direct reduction to H2O on the Pt surface and (ii) additional H2O2 formation and desorption on both Pt and carbon surfaces and subsequent partial re-adsorption and further reduction of the H2O2 molecules on the Pt surface. The potential of model studies on structurally defined catalyst surfaces and under well-defined mass transport conditions in combination with simulations for the description of electrocatalytic reactions is discussed.

0-18nm-thick titanium, zirconium and tantalum oxide films are thermally evaporated on Nation 117 membranes, and used as thin spacer electrolyte layers between the Nation and a 3 nm Pt catalyst fi ...

We demonstrate a flexible combined electrochemistry and fiber optics-based in situ UV/vis spectroscopy setup to gain insight into the depth evolution of electrochemical hydride and oxide formation in Pd films with thicknesses of 20 and 100 nm. The thicknesses of our model systems are chosen such that the films are thinner or significantly thicker than the optical skin depth of Pd to create two distinctly different situations. Low power white light is irradiated on the sample and analyzed in three different configurations; transmittance through, and, reflectance from the front and the back side of the film. The obtained optical sensitivities correspond to fractions of a monolayer of adsorbed or absorbed hydrogen (H) and oxygen (O) on Pd. Moreover, a combined simultaneous readout obtained from the different optical measurement configurations provides mechanistic insights into the depth-evolution of the studied hydrogenation and oxidation processes.

Fuel cells have the potential to play an important role in sustainable energy systems, provided that catalysts with higher activity and stability are developed. In this work, it is found that thin alloy films of single-target cosputtered platinum-yttrium exhibit up to seven times higher specific activity (13.4 +/- 0.4 mA cm(-2)) for the oxygen reduction reaction (ORR) than poly-crystalline platinum, and up to one order of magnitude higher mass activity (3.5 +/- 0.3 A mg(-1)) than platinum nanoparticles. These alloys have the highest reported ORR activity for an as-deposited material, i.e., without any additional chemical or thermal treatment. The films show an improvement in stability over the same materials in nanoparticulate form. Physical characterization shows that the thin films form a platinum overlayer supported on an underlying alloy. The high activity is likely related to compressive strain in that overlayer. As sputtering can be used to mass-produce fuel cell electrodes, the results open new possibilities for the preparation of platinum-rare earth metal alloy catalysts in commercial devices.

Ethanol is an alternative fuel for direct alcohol fuel cells, in which the electrode materials are commonly based on Pt or Pd. Owing to the excellent promotion effect of Ni2 P that was found in methanol oxidation, we extended the catalyst system of Pt or Pd modified by Ni2 P in direct ethanol fuel cells. The Ni2 P-promoted catalysts were compared to commercial catalysts as well as to reference catalysts promoted with only Ni or only P. Among the studied catalysts, Pt/C and Pd/C modified by Ni2 P (30 wt %) showed both the highest activity and stability. Upon integration into the anode of a homemade direct ethanol fuel cell, the Pt-Ni2 P/C-30 % catalyst showed a maximum power density of 21 mW cm(-2) , which is approximately two times higher than that of a commercial Pt/C catalyst. The Pd-Ni2 P/C-30 % catalyst exhibited a maximum power density of 90 mW cm(-2) . This is approximately 1.5 times higher than that of a commercial Pd/C catalyst. The discharge stability on both two catalysts was also greatly improved over a 12 h discharge operation.

In current polymer electrolyte fuel cells (PEMFC), high amounts of platinum catalysts is required due to the sluggish kinetics of the oxygen reduction reaction (ORR). As such it is important to find ways to increase the activity of the ORR catalyst. Previous studies have shown that alloying platinum with yttrium results in a catalyst which is more than six times as active as sole Pt in half cell rotating disk electrode measurements [1]. The model electrodes in this study are prepared by sputtering a well-defined layer of alloy catalyst onto a gas diffusion layer (GDL). In this manner the composition and thickness of the film can be controlled. These electrodes are studied with single cell PEMFC measurements to characterize the materials, similar to previous work done with these types of electrodes [2]. Using these methods the electrochemical surface area (ECSA), ORR activity, and stability are evaluated. The effects of different MEA preparations will also be investigated. Scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis as well and X-ray photoelectron spectroscopy (XPS) are used to characterize the structure of the alloy catalyst as well as the bulk and surface compositions, i.e. platinum to yttrium ratio. This characterization is performed on both as-prepared samples and electrodes after being used in the PEMFC. The main focus is to determine the role of yttrium in platinum thin-film platinum electrodes, and if the excellent activity in half cell experiments will also be seen in real PEMFC measurements. References [1] J. Greeley, I. E. L. Stephens, A. S. Bondarenko, T. P. Johansson, H. A. Hansen, T. F. Jaramillo, J. Rossmeisl, I. Chorkendorff and J. K. Nørskov , Nature Chemistry, 2009, 1, 552-556 [2] M. Wesselmark, B.Wickman,C.Lagergren,G.Lindbergh, Electrochimica Acta, 2013, 111, 152-159

Aiming at the investigation of spillover and transport effects in electrocatalytic reactions on bimetallic catalyst electrodes, we have prepared novel, nanostructured electrodes consisting of arrays of homogeneously distributed pairs of Pt and Ru nanodisks of uniform size and with controlled separation on planar glassy carbon substrates. The nanodisk arrays (disk diameter approximate to 60 nm) were fabricated by hole-mask colloidal lithography; the separation between pairs of Pt and Ru disks was varied from -25 nm (overlapping) via +25 nm to +50 nm. Morphology and (surface) composition of the Pt/Ru nanodisk arrays Were characterized by scanning electron microscopy, energy dispersive X-ray analysis, and X-ray Photoelectron spectroscopy, the electrochemical/electrocatalytic properties were explored by cyclic voltammetry, COad monolayer oxidation ("COad stripping"), and potentiodynamic hydrogen oxidation. Detailed analysis of the 2 COad oxidation peaks revealed that on all bimetallic pairs these cannot be reproduced by superposition of the peaks obtained on electrodes with Pt/Pt or Ru/Ru pairs, pointing to effective Pt-Ru interactions even between rather distant pairs (50 nm). Possible reasons for this observation and its relevance for the understanding of previous reports of highly active catalysts with separate Pt and Ru nanoparticles are discussed. The results clearly demonstrate that this preparation method is perfectly suited for fabrication of planar model electrodes with well-defined arrays of bimetallic nanodisk pairs, which opens up new possibilities for model studies of electrochemical/electrocatalytic reactions.

Transport effects in the methanol oxidation reaction (MOR) were investigated using nanostructured Pt/glassy carbon (GC) electrodes and, for comparison, a polycrystalline Pt electrode. The nanostructured Pt/GC electrodes, consisting of a regular array of catalytically active cylindrical Pt nanostructures with 55 +/- 10 nm in diameter and different densities supported on a planar GC substrate, were fabricated employing hole-mask colloidal lithography (HCL). The MOR measurements were performed under controlled transport conditions in a thin-layer flow cell interfaced to a differential electrochemical mass spectrometry (DEMS) setup. The measurements reveal a distinct variation in the MOR activity and selectivity (product distribution) with Pt nanostructure density and with electrolyte flow rate, showing an increasing overall activity, reflected by a higher Faradaic reaction current, as well as a pronounced increase of the turnover frequency for CO(2) formation and of the CO(2) current efficiency with decreasing flow rate and increasing Pt coverage. These findings are discussed in terms of the "desorption-readsorption-reaction" model introduced recently (Seidel et al. Faraday Discuss. 2008, 140, 67). Finally, consequences for applications in direct methanol fuel cells are outlined.

The role of transport and re-adsorption processes on the oxygen reduction reaction (ORR), and in particular on its selectivity was studied using nanostructured model electrodes consisting of arrays of Pt nanostructures of well-defined size and separation on a planar glassy carbon (GC) substrate. The electrochemical measurements were performed under controlled transport conditions in a double-disk electrode thin-layer flow-cell configuration; the model electrodes were fabricated by colloidal lithography techniques, yielding Pt nanostructures of well defined and controlled size and density (diameter: 140 or 85 nm, height: 20 or 10 nm, separation: from 1-2 to more than 10 diameters). The nanostructured model electrodes were characterized by scanning electron microscopy and electrochemical probing of the active surface area (via the hydrogen adsorption charge). The electrocatalytic measurements revealed a pronounced variation of the hydrogen peroxide yield, which increases by up to two orders of magnitude with increasing separation and decreasing size of the Pt nanostructures. Similar, though less pronounced effects were observed upon varying the electrolyte flow and thus the mass transport characteristics. These effects are discussed in a reaction model which includes (i) direct reduction to H(2)O on the Pt surface and (ii) additional H(2)O(2) formation and desorption on both Pt and carbon surfaces and subsequent partial re-adsorption and further reduction of the H(2)O(2) molecules on the Pt surface.