Search

Nonaqueous organic redox flow batteries (NAORFBs) show great promise for grid energy storage but are currently facing key challenges such as high electroactive material cost and low energy density....

Excitons have fundamental impacts on optoelectronic properties of semiconductors. Halide perovskites, with long carrier lifetimes and ionic crystal structures, may support highly mobile excitons because the dipolar nature of excitons suppresses phonon scattering. Inspired by recent experimental progress, we perform device modeling to rigorously analyze exciton formation and transport in methylammonium lead triiodide under local photoexcitation by using a finite element method. Mobile excitons, coexisting with free carriers, can dominate photocurrent generation at low temperatures. The simulation results are in excellent agreement with the experimentally observed strong temperature and gate dependence of carrier diffusion. This work signifies that efficient exciton transport can substantially influence charge transport in the family of perovskite materials.

Aqueous organic redox flow batteries (AORFBs) have drawn substantial attention due to their potential to simultaneously achieve high energy density, high power density and low cost, but its development has been hindered by cross-contamination between the negative and positive electrolytes. To address this issue, we demonstrate the first example of symmetric AORFBs using a single ionic compound, the aqueous organic bipolar mono-N-alkylated bipyridinium iodide salt [(bpy-(CH2)3NMe3)]I2, to serve the three functions of anolyte, catholyte and supporting electrolyte. This strategy has the potential to achieve high energy density with lower cost and in the meantime migitate the problem of cross-contamination. The trifunctional behaviour have been verified in the symmetric battery tests under neutral pH, which achieves an energy efficiency of 72% at the current density of 10 mA/cm2 within 100 cycles with a capacity retention rate of 99.5% per cycle. This chemical has superior electrochemical stability with no observable chemical degradation after 290 cycles.

Rheumatoid arthritis (RA) is a chronic autoimmune disease associated with changes in several hormones and metabolic peptides. Crosstalk between these factors and the immune system may be important for homeostasis during inflammation. Here, we studied the levels of hormones, metabolic peptides, and nutrients in individuals at risk for developing RA (at risk). In total, 18 hormones, metabolic peptides, and nutrients were measured in fasting serum samples from 45 autoantibody-positive individuals at risk, 22 RA patients, and 16 healthy subjects. Triglyceride (TG) levels were also measured in an independent validation cohort of 32 individuals at risk, 20 early arthritis patients, and 20 healthy controls. We found an elevated TG level in individuals at risk and significantly higher TG levels in RA patients compared to healthy controls. These results were confirmed in the validation cohort. Similarly, free fatty acid (FFA) levels showed an increase in individuals at risk and were significantly higher in RA patients compared to healthy controls. In RA patients, FFA levels were positively correlated with disease activity. Pancreatic polypeptide (PP) and norepinephrine levels were highly significantly increased in individuals at risk and RA patients compared to healthy controls. TG and FFA levels are increased in RA patients and positively correlated with disease activity parameters. The results presented here suggest a role for FFAs in the pathogenesis of RA. Furthermore, PP and norepinephrine may be a biomarker that could assist in the identification of individuals at risk. Electronic supplementary material The online version of this article (doi:10.1007/s10067-016-3456-x) contains supplementary material, which is available to authorized users.

RATIONALE Despite various porous materials having been widely adopted as spraying tips for direct sample analysis using electrospray ionization mass spectrometry (ESI-MS), the effect of surface property and porosity of spraying tip materials on their analytical performances is not clear. Investigation of their relationships could provide insight into the proper choice and/or design of spraying tip materials for direct sample analysis. METHODS The effect of spraying tip materials with different polarities, including polyester and polyethylene (hydrophobic) and wood (hydrophilic), on the detection sensitivity for a variety of compounds, and on the ESI onset voltage, were studied using ESI-MS. The porosity of each type of spraying tip was characterized by scanning electron microscopy (SEM). Factors governing the detection sensitivity were determined based on the correlation of the detection sensitivity to the ESI onset voltage, the polarity, and the porosity of the spraying tip materials. RESULTS Hydrophobic tips (i.e., polyester and polyethylene) show better detection sensitivity for polar compounds but not for non-polar compounds, while hydrophilic tips (wooden tips) show the opposite effect. This phenomenon could be due to the difference in interaction between the analytes and the tips, causing the analytes to adsorb on the tip to different extents. In addition, the micro-porous nature of the tips could facilitate solvent diffusion for transporting analytes to the tip and maintain a stable spray for recording MS data. With the proper choice of spraying tip materials, trace amount of analytes at the picomole level can be detected with minimal sample pretreatment. CONCLUSIONS Both the polarity and the porosity of the spraying tip materials could significantly affect detection sensitivity for a wide variety of analytes. With proper choice of spraying tip material, ESI on a porous spraying tip could be a sensitive method for the direct analysis of daily life samples. Copyright © 2013 John Wiley & Sons, Ltd.

Chrysotoxine is a naturally occurring bibenzyl compound found in medicinal Dendrobium species. We previously reported that chrysotoxine structure-specifically suppressed 6-hydroxydopamine (6-OHDA)-induced dopaminergic cell death. Whether chrysotoxine and other structurally similar bibenzyl compounds could also inhibit the neurotoxicity of 1-methyl-4-phenyl pyridinium (MPP(+)) and rotenone has not been investigated. We showed herein that chrysotoxine inhibited MPP(+), but not rotenone, induced dopaminergic cell death in SH-SY5Y cells. The overproduction of reactive oxygen species (ROS), mitochondrial dysfunction as indexed by the decrease in membrane potential, increase in calcium concentration and NF-κB activation triggered by MPP(+) were blocked by chrysotoxine pretreatment. The imbalance between the pro-apoptotic signals (Bax, caspase-3, ERK and p38 MAPK) and the pro-survival signals (Akt/PI3K/GSK-3β) induced by MPP(+) was partially or totally rectified by chrysotoxine. The results indicated that ROS inhibition, mitochondria protection, NF-κB modulation and regulation of multiple signals determining cell survival and cell death were involved in the protective effects of chrysotoxine against MPP(+) toxicity in SH-SY5Y cells. Given the different toxic profiles of 6-OHDA and MPP(+) as compared to rotenone, our results also indicated that DAT inhibition may partially account for the neuroprotective effects of chrysotoxine.

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) was applied to the direct analysis of melamine cyanurate (MC). The three commonly used MALDI matrixes, namely, alpha-cyano-4-hydroxycinnamic acid (CHCA), sinapinic acid (SA), and 2,5-dihydroxybenzoic acid (DHB), were able to desorb/ionize melamine from MC upon N(2) laser irradiation, with CHCA showing the highest detection sensitivity in the positive mode. Only DHB and SA were able to desorb/ionize cyanuric acid from MC in the negative mode but with remarkably lower sensitivity. The method is able to detect melamine unambiguously from a small amount of MC (down to 12.5 microg) spiked into urine and was successfully applied for the rapid and sensitive detection of melamine in urine stones/residues of the samples collected from patients clinically confirmed of having kidney stones associated with the consumption of melamine-tainted food products. The urine matrix resulted in interfering ion peaks and suppressed the ion intensity of melamine, while a cleanup process consisting of simply washing with water eliminated such interference and enhanced the ion intensity. The merit of the method is simplicity in sample preparation. The analytical time of the method for high-throughput analysis from the time of sample treatment to analysis is less than 7 minutes per sample, with sensitive detection of the presence of melamine in the urine stones/residues of the patient samples.

Aim: This study aimed to evaluate the effect of cardiac rehabilitation on changing patients’ exercise intensity and physiological outcomes. Methods: The study used a pre- and post-inter vention test design to evaluate an 8-week cardiac rehabilitation programme. The focus of this programme was supervised exercise and the content includeddiet, physical activity, stress management and risk factor management. Patients attended three 2-hour sessions every week and these were supervised by a nurse specialist. Results: After 8 weeks of cardiac rehabilitation, the patients’ exercise intensity, systolic and diastolic blood pressure, body mass index, total cholesterol, high-density lipoprotein cholesterol, lowdensity lipoprotein cholesterol, and triglycerides were all improved. However, except for the high density lipoprotein cholesterol levels, the improvements were not sustained at 3 months. Among behaviour changes, only the improved behaviour in smoking and exercise were maintained at 3 months. Conclusions: The results of this study indicate that cardiac rehabilitation is effective in improving cardiac patient outcomes in the short term but that other approaches, such as motivational interviewing and counselling, and strategies such as unsupervised exercise programmes in community settings, may be needed to maintain the physiological improvements.

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) was developed for spatial profiling of phytochemicals and secondary metabolites in integrated herbal tissue without solvent extraction. Abundant alkaloid ions, including (+)-menisperine (m/z 356), magnoflorine (m/z 342), stepharanine (m/z 324), protonated sinomenine (m/z 330), protonated sinomendine (m/z 338), and a metabolite at m/z 314, could be directly desorbed from alpha-cyano-4-hydroxycinnamic acid- (CHCA-) coated stem tissue of Sinomenium acutum upon N2 laser (337 nm) ablation, while the ion signals desorbed from sinapinic acid- (SA-) coated and 2,5-dihydroxybenzoic acid- (DHB-) coated stem tissue were at least 10 times weaker. Solvent composition in the matrix solution could have significant effects on the ion intensity of the metabolites. Under optimized conditions that maximize the ion intensity and form homogeneous matrix crystals on the tissue surface, spatial distributions of the metabolites localized in different tissue regions, including cortex, phloem, xylem, rim, and pith, and their relative abundances could be semiquantitatively determined. The three metabolites detected at m/z 356, 342, and 314 showed specific distributions in the herbal samples collected from different growing areas, while others were not. By applying principal component analysis (PCA), the characteristic metabolites in specific tissue regions could be easily determined, allowing unambiguous differentiation of the herbal samples from different geographic locations.

With a coating of gold nanoparticles (AuNPs), over-the-counter (OTC) drugs and Chinese herbal medicine granules in KBr pellets could be analyzed by Fourier Transform Infra-red (FT-IR) spectroscopy and Surface-assisted Laser Desorption/Ionization mass spectrometry (SALDI-MS). FT-IR spectroscopy allows fast detection of major active ingredient (e.g., acetaminophen) in OTC drugs in KBr pellets. Upon coating a thin layer of AuNPs on the KBr pellet, minor active ingredients (e.g., noscapine and loratadine) in OTC drugs, which were not revealed by FT-IR, could be detected unambiguously using AuNPs-assisted LDI-MS. Moreover, phytochemical markers of Coptidis Rhizoma (i.e. berberine, palmatine and coptisine) could be quantified in the concentrated Chinese medicine (CCM) granules by the SALDI-MS using standard addition method. The quantitative results matched with those determined by high-performance liquid chromatography with ultraviolet detection. Being strongly absorbing in UV yet transparent to IR, AuNPs successfully bridged FT-IR and SALDI-MS for direct analysis of active ingredients in the same solid sample. FT-IR allowed the fast analysis of major active ingredient in drugs, while SALDI-MS allowed the detection of minor active ingredient in the presence of excipient, and also quantitation of phytochemicals in herbal granules.

A gas chromatography/ion trap mass spectrometry method was used for the trace analysis of atrazine and its deethylated degradation product deethylatrazine in environmental water and sediment samples. The isotope dilution technique was applied for the quantitative analysis of atrazine at parts-per-trillion levels. Water samples were pre-concentrated by solid-phase extraction using a C18 cartridge while the sediment samples were extracted by sonication with methanol. The concentrated extracts were analysed by a GC/ion trap MS operated in the MS/MS method. The extraction recoveries for the analytes were better than 83% when 1 L of water or 10 g of sediment was analysed. The method detection limits were 0.75 ng/L and 0.13 ng/g for atrazine and deethylatrazine detected in water and sediment, respectively. The precisions of the method represented by the relative standard deviation were in the range of 3.2-16.1%. The method was successfully applied to analyse surface water and sediment samples collected from Bei...

This paper is concerned with the synthesis of 1,8,9,16-tetrahydroxytetraphenylene (3a) via copper(II)-mediated oxidative coupling, its resolution to optical antipodes, and its conversion to 1,8,9,16-tetrakis(diphenylphosphino)tetraphenylene (3b). On the basis of these chiral "linear" building blocks, three rodlike chiral complexes, triblock (R,R,R,R)-17 and (S,S,S,S)-20 and pentablock (R,R,R,R,R,R,R,R)-22, were constructed. As a hydrogen bond donor, racemic and optically active 3a was allowed to assemble with linear acceptors to afford highly ordered structures. A 1:1 adduct of 4,4'-bipyridyl and (+/-)-3a exists in a dimeric form of 3a linked by 4,4'-bipyridyl through hydrogen bonds. Pyrazine serves as a short linker between achiral parallel chains each formed by (+/-)-3a, while self-assembly of homochiral 3a into alternate parallel chains occurs in the adduct of 5,5'-dipyrimidine with (+/-)-3a. Self-assembly of (S,S)-3a or (R,R)-3a with 4,4'-dipyridyl yielded a packing of chiral double helical chains formed by chiral tetrol 3a molecules. A novel chiral ligand, (S,S)-23, derived from 3a was used in the asymmetric catalytic hydrogenation of alpha-acetamidocinnamate, yielding up to 99.0% ee and 100% conversion.

A reversed-phase LC-MS method with quadrupole-time of flight (QTOF) detection has been developed for the determination of four dinitro-toluenesulfonic acids and two amino-nitro-toluenesulfonic acids in groundwater. The analytes were separated by HPLC with 0.1% ( v/ v) formic acid as mobile phase modifier compatible with mass spectrometric detection. QTOF-MS analysis with negative ion electrospray ionization afforded good selectivity and sensitivity for analysis of the dinitro- and amino-nitro-toluenesulfonic acids. Structure elucidation and confirmation were accomplished by tandem mass spectrometry. Characteristic ions resulting from the loss of NO, NO(2), and SO(2) from the [M-H](-) ions were detected. An intense fragment ion at m/ z 80 representing the [SO(3)](-) ion was detected for all dinitro- and amino-nitro-toluenesulfonic acids. Solid-phase extraction using a co-polymer cartridge was developed for preconcentration of the analytes from water. Good recovery (85%) was achieved when 0.1% formic acid was added into the water samples before extraction. Method detection limits ranged from 10 to 76 ng L(-1) for the targeted compounds when 10 mL water was analyzed. Groundwater samples collected from wells close to a former ammunition plant in Stadtallendorf, Germany, were analyzed for the dinitro- and amino-nitro-toluenesulfonic acids.

Lead zirconate titanate (PZT) multilayer devices have been fabricated by a two-step sintering process. The multilayer structure was first sintered at 1280 °C for 5 min., then it was cooled to 1150 °C and kept for 1.5 h. The sintered PZT multilayer device was studied by scanning electron microscopy and X-ray diffraction. There was little inter-diffusion between the PZT layer and the palladium-silver (Pd/Ag) electrodes and the electrodes have a high conductivity after sintering. The PZT multilayer device has good ferroelectric properties as confirmed by hysteresis loop measurements. This two-step process avoids the sintering of the PZT device at 1280°C for a prolong period of time, and thus allows the use of Pd/Ag interleaving electrodes instead of platinum (Pt) electrodes, thereby reducing the manufacturing cost.

A series of C2 symmetric chiral ketones were designed and synthesized for catalytic asymmetric epoxidation of unfunctionalized olefins. Among those ketones screened, (R)-7, (R)-9, and (R)-10 were found to be highly efficient catalysts for epoxidation of trans-stilbenes with enantioselectivities in the range of 84−95%. Convincing evidence was provided for a spiro transition state of dioxirane epoxidation. Through the 18O-labeling experiment, chiral dioxiranes were found to be the intermediates in chiral ketone catalyzed epoxidation reactions.

A series of C2 symmetric chiral ketones were designed and synthesized for catalytic asymmetric epoxidation of unfunctionalized olefins. Among those ketones screened, (R)-7, (R)-9, and (R)-10 were found to be highly efficient catalysts for epoxidation of trans-stilbenes with enantioselectivities in the range of 84−95%. Convincing evidence was provided for a spiro transition state of dioxirane epoxidation. Through the 18O-labeling experiment, chiral dioxiranes were found to be the intermediates in chiral ketone catalyzed epoxidation reactions.

Sulfur (S) isotopes have been used to apportion the amount of biogenic and anthropogenic sulfate in remote environments, an important parameter that is used to model the global radiation budget. A key assumption in the apportionment calculations is that there is little isotope selectivity as reduced compounds such as dimethyl sulfide (DMS) are oxidized. This paper describes a method to determine, for the first time, the S isotope composition of methanesulfonic acid (MSA), the product of DMS oxidation. The isotope composition of MSA was measured directly by EA-IRMS and was used as an isotope reference for the method. Synthetic mixtures approximating the conditions expected for aerosol MSA samples were prepared to test this method. First, MSA solutions were measured alone and then in combination with MSA and SO4(2-). In synthetic mixtures, SO4(2-) was separated from MSA by precipitating it as BaSO4 prior to preparation of MSA for isotope analysis. The delta 34S value for MSA solutions was -2.6 per thousand (SD +/- 0.4 per thousand), which is not different from the delta 34S obtained from MSA filtrate after precipitating SO4(2-) from the mixture (-2.7 +/- 0.3 per thousand). However, these values are offset from direct EA-IRMS analysis of MSA used as the isotope reference by -1.1 +/- 0.2 per thousand, and this must be accounted for in reporting MSA measurements. The S isotope measurements using this method approach a limiting value above 300 microg of MSA. This is approximately equal to the MSA found in 20,000 m3 of air, assuming ambient concentrations of approximately 15 ng m(-3). Three samples of MSA from the Pacific Ocean measured using this technique have an average delta 34S value of +17.4 +/- 0.7 per thousand.

Paclitaxel (Taxol), a cytotoxic diterpene initially isolated from the bark of Taxus brevifolia (Pacific yew), has been approved for cancer treatment. Since total chemical synthesis is not economical, plant biotechnology can offer an alternative route for the production of this drug. Callus cultures were initiated from different explants of Taxus x media and Taxus cuspidata on various media using different plant growth regulators in different photo-regimes. Several fast growing, white, friable calli lines were established. Suspension cultures were initiated from these calli and the activities of suspension and immobilised cultures were monitored over 40 days in shake flasks and bioreactors. Cell immobilisation in reticulated polyurethane foam particles showed improved growth. Since the specific paclitaxel yield were the same for both suspended and immobilised cultures, higher biomass concentration in the immobilised cultures led to higher paclitaxel concentration in the medium.

A reversed-phase HPLC method was developed for analyzing sinigrin and gluconasturtiin in six vegetable and two Chinese herb samples. A gradient program and mobile phases using methanol and 0.05% trifluoroacetic acid containing 20 mM ammonium acetate allowed sufficient retention and separation of the glucosinolates in the sample extracts. Quadrupole time-of-flight tandem mass spectrometry in negative ion electrospray ionization was used to analyze the fractions collected from the HPLC elution to confirm the identification of the glucosinolates. The levels of sinigrin and gluconasturtiin in the vegetables and Chinese herbs were determined by using an external calibration method. Concentrations of gluconasturtiin in the Chinese herbs were more than 15 times higher than those of sinigrin. Detection limits were 18 nmol g(-1) for sinigrin and 4 nmol g(-1) for gluconasturtiin when 50 g of fresh vegetable was analyzed.

Taxol is a cytotcxic diterpene initially isolated from the bark of Taxus brevifolia (Pacific yew). It has been approved for use in cancer treatment. Since total synthesis is uneconomical, plant biotechnology can provide an alternative source for the drug. Callus was initiated from needles of Taxus media on different media under different conditions of light. Cell immobilisation in polyurethane foam particles showed improved growth.