Search

Rice straw (RS) was utilized to produce biogas, and its biogas residues (BR) were studied on different degradation time. When rice straw was digested, much biogas was produced with average 50% methane. In anaerobic condition, non-fiber contents were mainly digested in the initial 10 days. Meanwhile, the surface of rice straw fibers became rough and its onset decomposition temperature also rose from 170 °C to 210 °C. Cellulose and hemicellulose were digested from 10 days to 30 days, and it determined that the cellulose crystallinity declined from 44.9% to 40.1% and hydroxyl groups was also seen to decrease, which conduces to the reduction of polarity and hydroscopicity. However, lignin was hardly digested in the whole anaerobic process. Inevitably, lignin was accumulated to contribute to the thermal stability and mechanical properties of rice straw fibers. Furthermore, rice straw/low-density polyethylene (RS/LDPE) and biogas residues/low-density polyethylene (BR/LDPE) composites were prepared. Compared with RS/LDPE composites, BR/LDPE composites showed obviously better tensile and flexural properties. Consequently, biogas residues of rice straw have better chemical and physical properties than the undigested rice straw.

In order to reduce the negative ecological effects and environmental pollution caused by large-scale herbicide application in rice cultivation, a straw fiber mulch film (FMF) was developed. This study applied high-temperature enzymatic solution technology as a pretreatment process for rice straw (RS) fibers, causing beneficial physicochemical structural changes. Chemical composition, crystallinity index (CrI), degree of polymerization (DP), thermal stability, and other parameters of deconstructed RS fibers were analyzed. The change in CrI showed that appropriate pretreatment times can improve crystallinity, while excessively long pretreatment times caused crystallinity to sharply decrease from 44.65 wt% to 41.34 wt%. The C O bonds between lignin and hemicellulose were almost completely destroyed, confirming the deconstruction of linkages within RS fibers, making the material significantly softer and looser. Compared with untreated straw fibers, the mechanical pulping beating time decreased significantly, reducing energy consumption by 43.75%. The FMFs prepared with appropriate fermenting times exhibited improved mechanical properties. The tensile strength of FMF prepared using biological pretreatment fermentation (BPF) as a raw material increased from 11.26 N m g−1 to 15.68 N m g−1, exhibiting an increase of 39.25% compared to traditional fermentation (TF). This work provides a novel method, which has the potential to effectively control herbicides and support the development of sustainable agricultural systems.

The effects of soil burial on the biodegradation of biocomposite flower pots (BFP) made from straw fiber (SF) and hydrolyzed soy protein isolate/urea/formaldehyde (HSPI/U/F) copolymer resin were studied in detail. The microstructure, crystallinity, functional groups, mechanical, degradation and thermal property of the prepared SF with HSPI/U/F copolymer resin have been studied, and the degradation mechanism was also elucidated. XRD results showed that the bond breakage between SF and HSPI/U/F copolymer resin induced a decrease in relative degradation-resistant crystal structures. FTIR spectra showed that the methylolated HSPI units could form a cross-linking network with U/F and SF. The BFP degradation after soil burial was mainly attributed to the effects of microorganisms. The degradation products were environmentally friendly, because they were degradable and could fertilize the soil. In addition, the U/F adhesives were slightly degraded by the microorganisms due to the HSPI in the pots. The TG and DSC results showed that the molecular motion of the BFP matrix could be restricted by the degradation action and the content of HSPI, resulting in decreased crystallization enthalpy and showing good thermal property. The tensile strength of different reinforced samples was not significantly reduced in comparison to U/F resin, and still kept good mechanical performance. Thus, the prepared SF reinforced HSPI/U/F copolymer resins could have good potential for use in the field of biodegradable flower pots because of their good thermal property, mechanical property, biodegradability, and relatively low cost.

Rice straw fibers are potential raw materials that can be used to produce biogas and reinforcing fibers for composites. In order to ascertain the effects of anaerobic digestion on the structural properties of the fibers, the structure of fibrous residuals with different digestion time, including 0, 10, 20, and 30 days, were investigated. The normalized biogas production volume was 224 mL/g volatile solid of substrate, of which the methane content was about 50%. Fiber detergent analyses of the straw before and after 10 days digestion indicated that the cellulose levels increased from 34.3% to 41.3%, and cellulose crystallinity index ranged from 44.9% to 49.9%, respectively. After the rice straw had been digested for 30 days, the cellulose and hemicelluloses of the rice straw were partially degraded; the crystallinity index of the cellulose decreased from 44.9% to 40.1% based on XRD analyses, and the amount of hydroxyl groups were observed to decrease based on FT-IR analyses. Consequently, the polarity and hygroscopicity of the rice straw fibers were speculated to be lowered based on these observed changes. Furthermore, the relative amount of lignin in the straw residuals increased as digestion time increased, which increased the thermal stability of the resulting fibers. As a result of anaerobic digestion, the properties of the rice straw fibers for their use in plastic composites were enhanced.

The hydrolytes soy protein isolates (HSPI)-modified urea–formaldehyde (UF) resins were synthesized via copolymerization process. The best bonding strength is 1.50 MPa and improves 51.5% compared with pure UF. In addition, the formaldehyde emission decreased. The effect of (HSPI) on the biodegradable (UF) resins was investigated. Biodegradation was evaluated by composting under controlled conditions in accordance with ISO 14855. The faster degradation rate was obtained when lower hydrolysis degree of HSPI was added into the system. Characterization of the resulting samples was performed by attenuated total reflection Fourier transform infrared spectroscopy, thermo-gravimetric analysis, XRD, scanning electron microscopy, and AFM. The results showed that no evidence of biodegradation was found for UF resins. The UF modified with lower hydrolysis degree of hydrolytes soy protein isolates (HSPI) resulted in a faster degradation rate. The HSPI in the network of modified UF degraded first, which resulted in the ...

The hydrolyzed soy protein isolate (HSPI) was used to partially substitute urea to synthesis modified urea–formaldehyde (UF) adhesives via copolymerization process, in order to reduce the dependency on petroleum-based chemicals and mitigate possible environmental pollution. The soy protein isolate (SPI), HSPI, and modified UF adhesives were characterized by attenuated total reflection Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance (1H NMR), and thermo-gravimetric analysis (TGA). The bonding strength, adhesive properties, biodegradability, and micrographs of the UF and HSPI-modified UF after degradation were also measured. The results show that the SPI native structure is unfolded during the treatment with sodium hydroxide. The thermal stability of HSPI is better than SPI. HSPI can incorporate into the structure of cured UF adhesives with three different feeding methods. And the best bonding strength of modified UF adhesives is 1.31 MPa when HSPI is added at the first step. The form...

To improve the compatibility between rice straw and reinforcing polymers, rice straw (RS) was pretreated by an anaerobic process, and its biogas residues (BR) were acetylated with acetic anhydride (AA) to prepare acetylated biogas residues (ABR). The optimum conditions of acetylation were determined by orthogonal experiments. When acetylation was performed at 140 °C with 10 mL AA/g BR and 0.08 g catalyst/g BR, the maximum weight gain rate (WGR) obtained was 23.7%. Fourier transform infrared (FTIR) analysis showed that many hydroxyl groups were displaced by acetoxy groups. Scanning electron microscopy (SEM) showed that many defects of BR were filled by the acetylation, and an ester layer was formed over the BR surface. However, the lower crystallinity of ABR than the BR and RS affected the mechanical properties of acetylated biogas residue/low density polyethylene (ABR/LDEP) composite. Interestingly, the BR and ABR showed higher onset decomposition temperature, but they exhibited faster decomposition rates because of the lower crystallinity of BR and ABR. Furthermore, the mechanical properties of the RS/LDEP, BR/LDEP, and ABR/LDEP composites were analyzed. Compared with RS/LDEP composites, the BR/LDEP and ABR/LDEP composites showed obviously better tensile and flexural properties. Consequently, rice straw fibers attained excellent compatibility with non-polar polymers.

A composting treatment was employed in an effort to improve the processability of rice husks. Changes in the chemical composition, physical structure, and rheological properties of modified rice husks were analyzed. The results indicated that the average diameter of compost-treated samples was significantly higher than that of the untreated samples because they were able to adhere to each other by the bacterial protein. Scanning electron microscopy images showed that the epidermis became rugged and lumpy because the composition of rice husks (cellulose, hemicellulose, lignin, and pectin) was partially decomposed, an effect confirmed by the chemical composition and FTIR analysis. Thermogravimetric analysis showed that the composted samples had better thermal stability than the untreated ones. Stress-strain curves showed that the treated samples displayed a moderately significant change of slope at about 0 to 10% strain, and they had better mechanical properties than untreated samples. Juxtaposing the rheological properties of both untreated and treated samples determined that the latter had higher apparent viscosity as a result of degradation and bacterial protein effects. All results indicated that the composting treatment changed the physical, chemical, and rheological properties of the rice husks, which are beneficial for its utilization and processability.

The degradation behavior was investigated for eco-composite nursery containers (NCs) prepared with rice husk and cornstarch adhesive modified with urea formaldehyde (UF) as a wet strength agent. The wet shear strength, water absorption capacities, and biological degradation of NCs within soil were also investigated. Quantitative analysis of the thermal degradation behavior of different NC versions was performed by thermo-gravimetric analysis (TGA). The results demonstrated that the introduction of the UF agent accelerated the soil degradation of the NCs matrix to a certain extent. The maximum cumulative mass loss was 51.1% when the UF content of NCs was 8 wt.%. Moreover, the dry strength of the mixed urea formaldehyde-cornstarch adhesive (UCA) was increased by 108.9% compared with cornstarch adhesive (CA). The results of this work indicate the improved biodegradability of the NC eco-composites, which could make them potential sustainable alternatives for conventional plastic pots.

The hydrolyzed soy protein isolate (HSPI) with different hydrolysis degree was applied to modify urea-formaldehyde resins (UF) via copolymerization process. The properties of HSPI were characterized by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) and TGA. The results show that HSPI with different hydrolysis degree is obtained. 1H NMR and ATR-FTIR spectra indicate that HSPI with different hydrolysis degree can incorporate into the structure of cured and uncured UF. The UF modified with higher hydrolysis degree of HSPI possess more stable units and contribute to the lower exothermic peak temperature in DSC curves. The bonding strength of HSPI modified UF increases as the hydrolysis degree of HSPI increases at the hot-press temperature of 120°C and decreases at the hot-press temperature of 150°C. The best bonding strength is 1.53 MPa at the hot-press temperature of 135°C and improved 56.12% compared with UF. In addition, the formaldehyde emission is dramatically reduced. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41469.

A biodegradable planting container made with rice straw and starch adhesives modified by polyvinyl alcohol was studied in this paper. The effect of heat treatment and polyamide resin on the properties of planting containers was investigated. The physical property and biodegradability were characterized by means of hygroscopicity, FTIR, degradability, and the thermogravimetric analysis. The results showed that the dry strength of planting containers increased as a result of both treatments. The wet strength of planting containers increased as a result of heat treatment, while the wet strength of planting containers decreased as a result of polyamide resin. The hygroscopicity of planting containers decreased with heat treatment and polyamide resin. The effect of heat treatment was more obvious than the effect of polyamide resin. It was observed that the peak intensity and position were changed for the 3400 cm-1, 2900 cm-1, 1640 cm -1, 1500 cm-1, 1400 cm-1, and 1050 cm-1 under the treatment of polyamide resin. The weight loss of specimens treated with polyamide resin was larger because of the presence of nitrogen in the resin. The appearance of planting containers showed the heat treatment containers were not easily prone to mildew when used for planting. The thermogravimetric analysis (TGA) showed that heat treatment can improve the thermal stability, while the polyamide resin was shown to promote the degradation of planting containers.