Search

The CO oxidation reaction on carbon-supported Pt nanoparticles (average size of 2.8 to 7.7 nm) was studied under flowing conditions at atmospheric pressure and temperatures between 300 and 353 K by coupling quadrupole mass spectrometry (QMS) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). The Pt loading was varied between 20 and 60 wt%. Gases diluted in He (0.5 mol%) were used together with Ar as a tracer. Reactions with CO and O2 introduced separately onto the samples were studied by QMS, applying successive step changes of the reaction mixtures. Variations in the rate of the reactions were observed and correlated with changes of the calculated coverage of the Pt surface by CO and/or O adspecies at varying steps of the experiment. The transient reaction of CO(g) with adsorbed O (Oad) was fast and mass transport-limited while that of O2(g) with adsorbed CO (COad) was sluggish. Following the same experimental procedures, FTIR spectra of adsorbed CO after varying steps were recorded, confirming the variations of COad and Oad as determined by QMS and indicating changes in the CO distribution over varying types of Pt surface sites. The influence of the adlayer composition (co-adsorption of COad and Oad), the particle size/structure and some possible surface reconstruction effects on the CO oxidation rate were evidenced and discussed. The structure of the Pt nanoparticles supported on carbon appears as an important factor for the efficiency of the so-called O2 bleeding as a CO mitigation strategy in polymer electrolyte membrane fuel cells.

A nanostructured three-dimensional (3D) microbattery has been produced and cycled in a Li-ion battery. It consists of a current collector of aluminum nanorods, a uniform layer of 17 nm TiO(2) covering the nanorods made using ALD, an electrolyte and metallic lithium counter electrode. The battery is electrochemically cycled more than 50 times. The increase in total capacity is 10 times when using a 3D architecture compared to a 2D system for the same footprint area.

ENERGIE+KIC:VBE:PGE; CO adsorption on carbon-supported Pt nano-particles under operando conditions was studied by quadru-pole mass spectrometry and diffuse reflectance infrared fourier transform spectroscopy (DRIFTS). The Pt catalyst was also studied by high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). It was shown by HRTEM and XPS that Pt nanoparticles can be fully reduced by H-2 at room temperature instead of by conventional high-temperature treatment. The Pt dispersion was determined by XRD, HRTEM, and CO chemisorption techniques with an excellent agreement among them. The room-temperature H-2/O-2 titration method was also used, but if assuming H/Pt-s = O/Pt-s = 1, it led to the underestimation of the dispersion compared to the other techniques. The existence of adsorption sites inaccessible to H-2 (or O-2) but accessible to CO because of a stronger interaction with Pt was proposed to explain the results. It was also concluded that H/Pt-s was lower than unity (H/Pt-s = 0.72) and, as a major consequence, that Pt nanoparticles with 2.7 nm diameter still have a bulk-like behavior in contrast with what was reported in the literature for 1 nm Pt particles. CO adsorption on Pt/C at 298 K after H-2 treatment was studied by operando DRIFTS. The C-O stretching vibration (nu CO) bands were ascribed to CO adsorbed on Pt surface at (111)-terrace, (100)-terrace, edge, and kink sites in linear and bridge forms. An unexpected nu CO band at 1703 cm(-1) was observed upon CO adsorption and tentatively attributed to CO on surface Pt sites interacting through its oxygen end with the carbon support. It was also shown that the adsorption of CO and H-2 in successive repeated steps was necessary to reach a stable state of the adsorbed CO phase. Possible reconstruction of Pt nanoparticles at room temperature during this process is discussed.

Based on a multiscale modeling framework, we focus on understanding the impact of CO adsorption on the intrinsic stability properties of PtxCoy nanoparticles under PEMFC anode operating conditions. Firstly, CO adsorption effect on PtxCoy has been studied by using Monte Carlo (MC) simulation. Then, the MC results were coupled with a non-equilibrium thermodynamics kinetics model (MEMEPhys®) to simulate the effect of CO poisoning on the activity and durability of PtxCoy nanoparticles as HOR catalysts. The results are compared with simulations carried out on Pt, where potential self-oscillatory behaviour is observed and experimentally confirmed. The PtxCoy HOR activity and stability properties reveal to be strongly dependent on the nanoparticle size and composition. For certain nanoparticle sizes, simulations show that PtCo nanoparticles provide better CO tolerance than Pt3Co. However, the CO tolerance of PtCo degrades faster than that of Pt3Co in long-term operation. From both modeling and experimental approaches, it is demonstrated for the first time that this observation is due to the fact that CO adsorption enhances Cobalt dissolution.