Search

The development of silver (Ag) thin films and the fabrication of Ag nanosquare arrays with the use of an anodic aluminum oxide (AAO) template and leaf extracts were successfully carried out using the DC sputtering and spin coating deposition methods. Ag thin films and Ag nanosquare arrays are developed to monitor cancer prognosis due to the correlation between serum albumin levels and prognostic factors, as well as the binding of serum albumin to the surface of these electrodes. Nanosquare structures were fabricated using AAO templates with varying diameters and a gap distance between adjacent unit cells of 100 nm. The nanosquare array with a diameter of 250 nm and irradiated with electromagnetic waves with a wavelength of around 800 nm possessed the greatest electric field distribution compared to the other variations of diameters and wavelengths. The results of the absorption measurement and simulation showed a greater shift in absorption peak wavelength when carried out using the Ag nanosquare array. The absorption peak wavelengths of the Ag nanosquare array in normal blood and blood with cancer lymphocytes were 700–774 nm and 800–850 nm, respectively. The electrochemical test showed that the sensitivity values of the Ag thin-film electrode deposited using DC sputtering, the Ag thin-film electrode deposited using spin coating, and the Ag nanosquare array in detecting PBS+BSA concentration in the cyclic voltammetry (CV) experiment were 1.308 µA mM−1cm−2, 0.022 µA mM−1cm−2, and 39.917 µA mM−1cm−2, respectively. Meanwhile, the sensitivity values of the Ag thin film and the Ag nanosquare array in detecting the PBS+BSA concentration in the electrochemical impedance spectroscopy (EIS) measurement were 6593.76 Ohm·cm2/mM and 69,000 Ohm·cm2/mM, respectively. Thus, our analysis of the optical and electrochemical characteristics of Ag thin films and Ag nanosquare arrays showed that both can be used as an alternative biomedical technology to monitor the prognosis of blood cancer based on the concentration of serum albumin in blood.

This study has been successfully synthesized Nickel (Ni)-doped olivine-type LiNixFe1-xPO4/C with x= 0, 0.01, 0.02, 0.03 as cathode materials, using the solid-state reaction method was in order to investigate the effect on the structure and morphology. The precursor material of ion Ferro (Fe) is used natural material from ironstone of Tanah Laut Kalimantan Indonesian which combined with proanalis materials. The X-Ray Diffraction (XRD) patterns on the structure magnetite iron have shown that single phase of Fe3O4 and the patterns of structure LiNixFe1-xPO4/C indicated that doping Ni2+ have shown the orthorhombic structure with space group Pnma for all LiNixFe1-xPO4/C samples. Base on Rietveld method by Rietica software, the formation of phase resulted in olivine structure except at the concentration x = 0.02 and 0.03 have a second phase, that is nasicon structure with a smaller percentage than olivine structure. The general condition, coating carbon on LiNixFe1-xPO4/C particles by solid state reaction can be perfect which demonstrate the homogeneous existence of carbon on the surface of LiNixFe1-xPO4/C particles shown by images Scanning Electron Microscopy (SEM). The increased doping of Ni ions causing the Fe ions to decrease base on Energy Dispersive X-Ray Spectroscopy (EDS) observations.

This study aims to evaluate the capability of Ageratum conyzoides and Mikania micrantha extracts to synthesize silver nanoparticles (AgNPs) and their antibacterial capability against gram-positive and gram-negative bacteria. Several properties of the synthesized AgNPs, including plasmonic, biomolecule bonding, shape, size, and antibacterial, were investigated. Ultraviolet–visible (UV–vis) spectroscopy was employed for characterizing their plasmonic properties. Functional groups on the produced AgNPs were investigated by Fourier-transform infrared (FT-IR) spectroscopy. The size and shape of the AgNPs were identified using the field-emission scanning electron microscopy (FESEM). Inhibition zone measurement was carried out for evaluating the antibacterial capability. This study showed that the extracts of A. conyzoides and M. micrantha were able reducing agents as evidenced by the formation of the spherical AgNPs. UV–vis spectroscopy, FT-IR spectroscopy, and FESEM confirmed the physicochemical characteristics of AgNPs. AgNPs that were synthesized using M. micrantha were slightly smaller than those produced using A. conyzoides. In general, the present work establishes that the synthesized AgNPs have antibacterial capability depending on their size and synthesis procedure.

Dye-Sensitized Solar Cell (DSSC) is the third generation of solar cells. DSSC is formed by sandwich structure, there are five parts: ITO glass (Indium Tin Oxide) as the substrate; TiO2 and SnO2 as semiconductor material; natural dye from chlorophyll as an electron donor; gel electrolyte as electron transfer and active carbon as a catalyst in the counter electrode. The synthesis of nanometer-sized TiO2 powder is obtained by coprecipitation method. The layer of TiO2 was deposited on top of an ITO glass by doctor blade method. From the research, the DSSC efficiency has increased by nearly 100% after additions SnO2 to TiO2. The DSSC efficiency result is 0.05% for DSSC before additions and 0.1% after additions

Carbon electrodes have been successfully synthesized and characterized for desalination system based on Capacitive Deionization (CDI) technology. The carbon electrodes were synthesized with an activated carbon (700 – 1400 m2/g), carbon black, glutaric acid and polyvinyl alcohol as a binder using cross-linking method at 120 °C. The study was to investigate salt removal percentage value of 0.1 M NaCl, MgCl and KCl using CDI cell. A solution with 0.1 M was supplied to the cell using a Boyu Submersible pump (model SP-601) at a flow rate of 10 mL/min. When potentials of 1.0, 2.0, and 3.0 V were applied to the CDI cell, the result showed that a solution of 0.1 M KCl has greater salt-removal percentage than the solutions with 0.1 M NaCl and MgCl. The salt-removal percentage of KCl was achieved at 55% for 3.0 V whilst resulted in 20 and 30% for NaCl and MgCl, respectively.

The influences of electron discharge and magnetic field on calcium carbonate (CaCO3) precipitation in water have been successfully investigated. The study used three pairs of magnetic field 0.1 T whilst the electron discharge was generated from television flyback transformer type BW00607 and stainless steel SUS 304 as an electrode. The water sample with an initial condition of 230 mg/L placed in the reactor with flow rate 375 mL/minutes, result showed that the electron discharge can be reduced contain of calcium carbonate the water sample around 17.39% within 2 hours. Meanwhile for the same long period of treatment and flow rate, around 56.69% from initial condition of 520 mg/L of calcium carbonate in the water sample can be achieved by three pairs of magnetic field 0.1 T. When the combination of three pairs of magnetic field 0.1 T and the electron discharge used for treatment, the result showed that the combination of electron discharge and magnetic field methods can be used to precipitate calcium carbonate in the water sample 300 mg/L around 76.66% for 2 hours of treatment. The study then investigated the influence of the polar position of the magnetic field on calcium carbonate precipitation. Two positions of magnetic field were tested namely the system with alternated polar magnetics and the system without inversion of the polar magnetics. The influence of the polar position showed that the percentage reduction in levels of calcium carbonate in the water sample (360 mg/L) is significant different. Result showed that the system without inversion of the polar magnetics is generally lower than the system with alternated polar magnetics, with reduction level at 30.55 and 57.69%, respectively.

Carbon electrodes have been fabricated with the cross-linking methods at 120°C, using polyvinyl alcohol (PVA) as a binder and citric acid (CA) as a crosslinking agent. The carbon electrodes have been analyzed with Fourier Transform Infra Red Spectroscopy (FTIR) and the bound between PVA and citric acid of these electrodes have been analyzed as well. The surface and structural properties, as well as the electrochemical behaviors of the prepared electrode, were characterized by cyclic voltammetry (CV), and Electrical Impedance Spectroscopy (EIS). The specific capacitance of the carbon electrode and the desalination efficiency of the capacitive deionization (CDI) cell were achieved 15.7 F/g and 49.15%, respectively.

Carbon electrodes prepared with crosslink method for desalination purpose has been synthesized and characterized. The carbon electrodes were synthesized with activated carbon (700 – 1400 m2/g) and polyvinyl alcohol (PVA) as a binder using crosslink method with temperature crosslink at 120°C. Electrochemical properties of carbon electrodes were examined using electrical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The proposed study was to measure the salt-removal percentage of 330 µS/cm NaCl using a capacitive deionization (CDI) unit cell prepared with two pairs of carbon electrodes. The applied potential of 2.0 V and a flow rate of 25 mL/min were used to desalination tests. The result showed that the greatest value of the percentage of salt-removal was achieved at 36.1% for the carbon electrodes with Active Carbon Modified (ACM) while the salt-removal percentage for the Active Carbon (AC) electrodes only at 22%. The fact indicates that the active carbon modified using HNO3 can improve the ef...

Bolus is widely used to protect and reduce irradiation in organ at risk in the process of radiotherapy. Generally, the bolus was made from polymer material due to had property is similar or equivalent to tissue. This study aimed to determine the density, transmission factor, effective mass attenuation coefficient on bolus with radiation of photons and electrons. The bolus material (B) was used Propylene Glycol (PG), Silicon Rubber (SR) and Aluminium Powder (Al), and had four types of bolus namely B - PG 24%, B - PG 24%; SR 8%, B - PG 24%; SR 8%; Al 0,5%, and B - PG 24%; SR 8%; Al 1,5% with dimensions of 11 × 11 cm and thickness of 1 and 1.5 cm. The bolus density is evaluated through the mass of each volume. The measured data revealed that all of the boluses have density values which are similar to tissue or water and air in the range from 0,864 - 1,202 g/cm3. For dosimetry testing, the bolus is irradiated using Linear Accelerator with 6 and 10 MV for photon source and 6 and 12 MeV for an electron source. The results showed that B - PG 24%; SR 8%; Al 1.5% for dosimetry testing both 6 and 10 MV photons obtained properties that resemble soft tissue. Meanwhile, for both dosimetry testing of 12 MeV electrons, the B - PG 24%; SR 8% with addition silicone rubber and aluminum have nature closest to soft tissue. All of the boluses that have been fabricated have properties similar to soft tissue for photon therapy whereas the addition of more aluminum making a bolus has features as a shield on the process of radiotherapy.

Carbon electrodes for desalination purpose have been successfully synthesized using activated carbon powder (BET surface area=700 – 1400 m2/g), carbon black and polyvinyl alcohol (PVA) binder by cross-linking method with glutaric acid (GA) at 120 °C. The electrochemical properties of the carbon electrodes were analyzed using electrical impedance spectroscopy (EIS) and cyclic voltammetry (CV) whilst the physical properties were observed with scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX). In order to assess the desalting performance, salt removal experiments were performed by constructing a capacitive deionization unit cell with five pairs of carbon electrodes. For each pair consisted of two parallel carbon electrodes separated by a spacer. Desalination and regeneration processes were also observed in the salt-removal experiments. The salt-removal experiments were carried out in single-pass mode using a solution with 0.1 M NaCl at a flow rate of 10 mL/min. A voltage of 3 V...

Carbon electrodes prepared with freezing thawing method for desalination purpose has been synthesized and characterized. The carbon electrodes were prepared with an activated carbon (700 – 1400 m2/g) and polyvinyl alcohol (PVA) as a binder using freezing thawing method with 3 and 4 cycles (1 cycle is 12 hours for freezing and 12 hours for thawing). Electrical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to analyze their electrochemical properties. The main study was to measure the salt-removal of 180 µS/cm NaCl, MgCl and KCl using a capacitive deionization (CDI) unit cell with five pairs of carbon electrodes. The applied potential of 2.0 V and a flow rate of 25 mL/min were used to desalination tests, the result showed that the salt-removal percentage of KCl solution has greater than NaCl and MgCl. The highest value for the salt-removal of NaCl, KCl and MgCl can be achieved for the freezing thawing method with 4 cycles. The salt-removal percentage of KCl was achieved at 64.10% whilst ...

Ion-exchange membrane technology has shown a great potential to enhance the desalting efficiency. Ion-exchange membranes are placed in front of the electrodes so that the charged ions can be selectively passed through the membrane layer and captured by the oppositely charged electrode more quickly, so as to increase the efficiency of desalination. In this research, carbon electrodes have been synthesized from an activated carbon (700 – 1400 m2/g) and polyvinyl alcohol (PVA) as a binder using freezing thawing method. A solution with 180 µS/cm NaCl was pumped to the capacitive deionization (CDI) cell using a Boyu Submersible pump (model SP-601) at a flow rate of 25 mL/min and the voltage was set at 2 V. The result showed that the CDI cell with ion-exchange membrane (MCDI) has the salt removal efficiency greater than the CDI cell without ion-exchange membrane. The salt-removal percentage of MCDI was achieved at 66.36%, meanwhile the CDI cell without ion-exchange membrane resulted in 54.4%.

The synthesized carbon from bones of chicken, cow, and fish with the calcination temperature at 450 and 600°C have been successfully fabricated for counter electrode in the Super Low-Cost Solar Cell (SLC-LC) based the structure of Dye-Sensitized Solar Cells (DSSC). The main proposed study was to fabricate SLC-SC and investigate the influence of the synthesized carbon from animal's bone for counter electrode towards to photovoltaic performance of SLC-SC. X-Ray Diffraction and UV-Vis was used to characterize the phase and the optical properties of TiO2 as photoanode in SLC-SC. Meanwhile, the morphology and particle size distribution of the synthesized carbon in counter electrodes were investigated by Scanning Electron Microscopy (SEM) and Particle Size Analyzer (PSA). The results showed that the TiO2 has anatase phase with the absorption wavelength of 300 to 550 nm. The calcination temperature for synthesizing of carbon could affect morphology and particle size distribution. The increasing temperature gave the effect more dense in morphology and increased the particle size of carbon in the counter electrode. Changes in morphology and particle size of carbon give effect to the performance of the SLC-SC where the increased morphology's compact and particle size make decreased in the performance of the SLC-SC.

Attachment of bacteria to surfaces and subsequent biofilm formation remains a major cause of cross-contamination capable of inducing both food-related illness and nosocomial infections. Resistance to many current disinfection technologies means facilitating their removal is often difficult. The aim of this study was to investigate the efficacy of 405 nm light for inactivation of bacterial attached as biofilms to glass and acrylic. Escherichia coli biofilms (10(3)-10(8) CFU mL(-1)) were generated on glass and acrylic surfaces and exposed for increasing times to 405 nm light (5-60 min) at ca 140 mW cm(-2). Successful inactivation of biofilms has been demonstrated, with results highlighting complete/near-complete inactivation (up to 5 log10 reduction on acrylic and 7 log10 on glass). Results also highlight that inactivation of bacterial biofilms could be achieved whether the biofilm was on the upper "directly exposed" surface or "indirectly exposed" underside surface. Statistically significant inactivation was also shown with a range of other microorganisms associated with biofilm formation (Staphylococcus aureus, Pseudomonas aeruginosa and Listeria monocytogenes). Results from this study have demonstrated significant inactivation of bacteria ranging from monolayers to densely populated biofilms using 405 nm light, highlighting that with further development this technology may have potential applications for biofilm decontamination in food and clinical settings.

Carbon electrodes for desalination system have successfully been synthesized with and/or without modified activated carbon by chemically activated using HNO3. The freezing-thawing method was used to synthesize the carbon electrodes. In this study, 5 cycles of freezing-thawing were applied in the synthesized carbon electrodes (1 cycle is 12 hours for freezing and 6 hours for thawing). Electrochemical properties of the synthesized carbon electrodes with and/or without modified activated carbon were characterized and observed by cyclic voltammetry (CV) and Electrical impedance spectroscopy (EIS). The salt-removal percentage experiments were conducted to evaluate the performance of capacitive deionization (CDI) cell using the two pairs of carbon electrodes with each pair consisting of two parallel electrodes that separated by a spacer. The result showed that the salt removal percentage of the carbon electrodes with modified activated carbon has greater than the carbon electrodes without modified activated carbon, with reduction level at 55.7 and 24.8%, respectively.

Dye-sensitized Solar Cell (DSSC) is a third-generation solar cell that consists of a working electrode, electrolyte and counter electrode. One of the most important parts of DSSC is an electrolyte that roles as a medium and regenerates the electron transport of electrons in the dye. However, the liquid electrolyte has a lack of stability in long-term use and easily evaporate or leak in DSSC. Therefore, this study aims to investigate an effect of the addition of polymer material such as PEG 1000, 4000 and PVA 60000 for fabricating a gel electrolyte to solve the problems of liquid electrolyte. The synthesized TiO2 nanoparticles used in this study was prepared using co-precipitation (CPT) method which produces TiO2 anatase phase with a crystal size of 11.1 nm. DSSC has been successfully conducted and analyzed to evaluate its performance. The results showed that the efficiency of DSSC cells using gel electrolyte prepared with PVA 60000 was better than a liquid electrolyte, PEG 1000, 4000, with the efficiency could be obtained at 0.083, 0.018, 0.033, and 0.054%, respectively. The results demonstrated that the addition PEG and/or PVA could be enhanced the performance of DSSC due to gel electrolyte produced current and voltage more stable compared to the liquid electrolyte.

Dye Sensitized Solar Cell (DSSC) using natural dyes (chlorophyll, curcumin from turmeric extract, and anthocyanin from mangosteen extract) have been successfully fabricated for determining the effect of variation natural dyes, mixing dyes and acetonitrile in electrolyte toward characterization of DSSC. DSSC consists of five parts namely ITO (Indium Tin Oxide) as a substrate; TiO2 as semiconductor materials; natural dyes as an electron donor; electrolyte as electron transfer; and carbon as a catalyst that can convert light energy into electric energy. Two types of gel electrolyte based on PEG that mixed with liquid electrolyte have utilized for analyzing the lifetime of DSSC. Type I used distilled water as a solvent whilst type II used acetonitrile as a solvent with addition of concentration of KI and iodine. The main purpose of study was to investigate influence of solvent in electrolyte, variation of natural dyes and mixing dyes toward an efficiency that resulted by DSSC. The result showed that electrolyte type II is generally better than type I with efficiency 0,0556 and 0,0456 %, respectively. An efficiency values which resulted from a variation of mixed three natural dyes showed the greatest efficiency compared to mixed two natural dyes and one dye, with an efficiency value can be achieved at 0,0194 % for chlorophyll; 0,111 % for turmeric; 0,0105 % for mangosteen; 0,0244% (mangosteen and chlorophyll); 0,0117 % (turmeric and mangosteen); 0,0158 % (turmeric and chlorophyll); and 0.0566 % (mixed three natural dyes).

It has been created microcontroller-based ozone sterilization system which is used for E. Coli bacteria sterilization. The created system consists of a neon sign transformer, corona electrode, ozone gas chamber container and ozone gas metering systems. Neon sign transformer and corona electrode are then assembled into an ozone generator that works on the principle of corona discharge. The use of ozone generators is controlled by microcontroller system. Ozone gas is produced by ozone generators which housed in a chamber and equipped by ozone gas indicator. The results of ozone gas effect testing in E. Coli with varied exposure of 15, 30 and 45 minutes showed the decrease number of E. Coli colonies of tested bacteria samples compared to the control sample without ozone gas exposure.

Activated carbon (AC), black carbon (BC), and graphite were deposited onto ITO (Indium Tin Oxide) glass for counter electrode application in Dye-Sensitized Solar Cells. SEM-EDX was used to observe and analyse the morphology and composition of electrodes. The results showed that the particle distribution of the graphite electrode observed was approximately 34% with a size of 1 to 2 µm and BC electrode about 20% have a size of 0.5 to 1 µm, while AC electrode has a size of 0 – 0.5 µm observed around 20%. AC electrode has a more porous and uniform particle aggregates compared to BC and graphite electrodes. The efficiency of the counter electrode was measured using the solar simulator. The highest efficiency was at 0.011516% for the counter electrode that was fabricated by AC. Meanwhile, black carbon and graphite electrodes were achieved at 0.008744% and 0.010561%, respectively. The results proved that the porosity and the uniform aggregate of the particles were the most significant factors to improve the performance of DSSC.