Search

Abstract: The mechanism of N2O decomposition was studied on a series of Fe-ZSM-5 catalysts prepared by ion exchange (IE) and chemical vapor deposition (CVD). N2O decomposition activity depends strongly on the extent of autoreduction of the catalyst during the pretreatment in He at high temperatures. The extent of autoreduction is significantly lower for catalysts prepared by CVD compared with that for catalysts prepared by aqueous ion exchange. As a result, the global turnover frequencies of the ion-exchanged catalysts are significantly higher. If the activity is normalized by the concentration of Fe2+ sites, however, then the CVD catalyst is the most active sample. This is attributed to the fact that high iron loading favors the surface migration and recombination of surface oxygen atoms to O2, which is the rate-limiting step of the reaction. O2 formation by slow recombination of two surface oxygen atoms is the dominating mechanism even for IE samples with very low iron loadings. [Copyright &y& Elsevier]

Abstract: The mechanism of decomposition of N2O on Fe-ZSM-5 prepared by chemical vapor deposition was studied by step and pulse response experiments and by isotope labeling. The results show that only a very small fraction of the iron sites is taking part in the catalytic cycle. N2O deposits its oxygen atoms on these sites, the deposited oxygen atoms migrate over the iron cluster, exchange with other oxygen atoms and then desorb by recombination to O2. On strongly dehydroxylated iron sites also a direct recombination of two oxygen atoms, which were deposited from N2O, is possible. The concentration of these sites increases after treatment of the samples at high temperatures in inert gas. The relation between the sites involved in N2O decomposition and the α-sites, which were first described by the group of Panov, is discussed. We can conclude that the deposition of N2O on Fe-ZSM-5 CVD catalysts creates active oxygen species on the catalyst surface (in particular, after pretreatments at high temperature), but their properties are different from those of α-oxygen. [Copyright &y& Elsevier]

The effect of pretreatment conditions on the N2O-decomposition activity of Fe-ZSM-5 prepared by chemical vapor deposition (CVD) was studied by steady-state kinetics and step-response experiments. Pretreatment at 873 K in H2 or He significantly increased the N2O-decomposition activity of Fe-ZSM-5 CVD. In addition to the increased steady-state activity, the catalyst exhibited a very high initial activity in the step-response experiments, which slowly decayed to steady state. This “transient” activity was particularly high after pretreatment of the samples in He, whereas it vanished completely after pretreatment in O2 or exposure to water vapor. This led to the conclusion that the transient activity is related to strongly dehydroxylated Fe2+ sites created by autoreduction at high temperatures. On the basis of isotope-labeling data a mechanism for N2O decomposition is proposed. The first step is the reaction of Fe2+ with N2O to give a Fe3+O- species, which quickly transforms into a Fe2+–peroxo complex. Desorption of O2 occurs upon reaction of the complex with another N2O molecule (mainly during the transient) or via the recombination of two peroxo species after their migration over the iron oxide cluster (mainly during steady state). [Copyright &y& Elsevier]

Abstract: The N2O decomposition activity of the Fe-ZSM-5 catalysts, prepared by chemical vapor deposition (CVD) and aqueous ion exchange (IE), was studied after steaming and high temperature treatment at 1218K (HT) and compared with the activity of the corresponding non-steamed catalysts after pretreatment at 873K. FTIR spectra showed that dehydroxylation and/or dealumination took place during steaming and high temperature treatment of the catalysts, which leads to the formation of oxygen vacancies (i.e. lattice defect). These lattice defects leads to a change in electronic properties of the iron sites, which are associated with electron withdrawing Al Lewis centers. The iron sites in close proximity of defects are responsible for the initial higher N2O decomposition (transient activity) of the steamed and HT catalysts. The increase in steady-state activity over steamed and HT catalysts can be mainly attributed to an increase in the number of active sites created by autoreduction of the iron centers during steaming and high temperature treatment. The above-mentioned trends are valid for both CVD and IE samples. [Copyright &y& Elsevier]