Search

This paper describes for the first time the fabrication of pencil drawn electrodes (PDE) on paper platforms for capacitively coupled contactless conductivity detection (C(4) D) on electrophoresis microchips. PDE-C(4) D devices were attached on PMMA electrophoresis chips and used for detection of K(+) and Na(+) in human tear samples. PDE-C(4) D devices were produced on office paper and chromatographic paper platforms and their performance were thoroughly investigated using a model mixture containing K(+) , Na(+) , and Li(+) . In comparison with chromatographic paper, PDE-C(4) D fabricated on office paper has exhibited better performance due to its higher electrical conductivity. Furthermore, the detector response was similar to that recorded with electrodes prepared with copper adhesive tape. The fabrication of PDE-C(4) D on office paper has offered great advantages including extremely low cost (< $ 0.004 per unit), reduced fabrication time (< 5 min), and minimal instrumentation (pencil and paper). The proposed electrodes demonstrated excellent analytical performance with good reproducibility. For an inter-PDE comparison (n = 7), the RSD values for migration time, peak area, and separation efficiency were lower than 2.5, 10.5, and 14%, respectively. The LOD's achieved for K(+) , Na(+) , and Li(+) were 4.9, 6.8, and 9.0 μM, respectively. The clinical feasibility of the proposed approach was successfully demonstrated with the quantitative analysis of K(+) and Na(+) in tear samples. The concentration levels found for K(+) and Na(+) were, respectively, 20.8 ± 0.1 mM and 101.2 ± 0.1 mM for sample #1, and 20.4 ± 0.1 mM and 111.4 ± 0.1 mM for sample #2., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

We investigated the effect that two common types of cationic polyelectrolytes used in papermaking might have on the performance of paper diagnostics using blood typing as an example. The results were analyzed in terms of red blood cells (RBC) retention and antibody-antigen specificity. Two questions were addressed: (1) can poly(amido-amine) epichlorohydrin (PAE) typically used for paper wet strength affect the diagnostic performance? (2) can high molecular weight cationic polyacrylamide (CPAM) employed as retention aid enhance or affect the selectivity and sensitivity of paper diagnostics? A series of paper varying in type of fibers and drying process were constructed with PAE and tested for blood typing performance. Residual PAE has no significant effect on blood typing paper diagnostics under normal conditions. Positives are unaffected with PAE, while negatives lose slight sharpness as some RBCs are unselectively retained. CPAM, the most common retention aid, can also be used to retain cells and biomolecules on paper. Paper towel was treated with CPAM solutions varying in polymer concentration and charge density and tested for blood typing. We found that CPAM dried on paper can retain RBC. CPAM affects the negative tests by retaining non-specifically individual RBC on fibers. RBC retention increases non-linearly with the CPAM charge density and concentration. As expected, wet CPAM retain RBCs at concentrations higher than 0.1wt%. As paper diagnostics are becoming a reality, more realistic papers than the Whatman filter paper will be engineered. This study provides guidance on how best use the required polymeric wet-strength and retention agents., (Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.)

To achieve efficient and safe cationic carrier-mediated gene delivery for gene therapy, the optimal ratio of carrier to DNA in formulations is a key factor and it is usually determined prior to transfection experiments. In this work, a simplified drop-and-read assay was developed for the first time using paper as a platform to estimate the equivalence ratio of cationic carriers to negatively charged DNA. By spotting a series of complexes containing varied ratios of carrier to DNA on filter paper, then allowing them to dry and finally dropping yellowish-green anionic 2',7'-dichlorofluorescein dye solution on top of the complexes, the equivalence point was detectable by the instant formation of stable pink spots as a result of the dye adsorption onto the positively charged complexes and free carriers. The method gave the same results as those determined by gel retardation assay and zeta potential measurement, however it allowed more rapid reporting of results in 5 min and required no tedious steps, harmful reagents or expensive instruments. By using paper instead of microcentrifuge tubes and omitting centrifugation, plasticware and electrical energy were no longer consumed and disposal of this degradable material was more environmentally friendly. With respect to analytical performance, filter paper inherently holding negative charge helped to trap and concentrate the complexes on the white background, enabling greater visibility of the colored spots and a lower required amount of DNA used for the assay. The method was successfully applied to estimate the equivalence ratios in a variety of gene delivery formulations containing different types of cationic carriers, i.e. polymers, dendrimers, liposomes and niosomes., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Spherical lignin cation adsorption resin was obtained by two-step method with black liquor of paper mill and characterized by the Scanning electron microscopy (SEM) and Fourier transform infrared spectrometry (FTIR). Firstly, the spherical lignin beads were prepared with black liquor of paper mill by applying reverse-phase suspension polymerization technique, and the preparation conditions were also optimized. The suitable conditions include 200 r/min of stirring speed, 90 degrees C of reaction temperature, 1.0 h of reaction time and use epoxy chloropropane (1.5% by weight of lignin) as cross-linking agent, the ideal volume ratio between oil phase and water phase was 3:1 by using kerosene oil as disperse phase, and the perfect dispersant agent was Tween 80 (3% by weight of lignin). Secondly, the spherical lignin cation adsorption resin was developed by grafting the acrylamide onto the back-bone of the spherical lignin beads. The best concentration of acrylamide was 0.72 mol/L at ambient temperature for 2.0 h, and the ideal initiator system was the Fenton reagent of H2O2/Fe2+. Under the above conditions, the ion exchange capacity of the prepared resin could reach 1.640 5 mmol/g.

Added Al2SO4 greatly accelerates the hydrolysis at 150.0 degrees C of 1,5-anhydrocellobiitol, a model for the beta(1 --> 4) linkages in cellulose, in succinate buffers of room temperature pH 3.05 and 3.35; E(a) values for 20 mM Al(III)- and H+-catalysed hydrolyses are 109 +/- 3 and 140 +/- 1 kJ mol(-1), respectively.

When the degree of closure of the paper machine wet end waters increases, wet end problems also become more difficult to control without specific and selective on-line measurements. The need to measure the concentrations of individual compounds in order to explain wet end phenomena is growing. This study was performed to set up a CE system to a paper machine and to determine soluble inorganic and organic ions in different locations of pulp and paper process waters with real time analyses by two on-line CE methods. A reconstructed commercial CE apparatus was connected to a papermaking machine via an apparatus, which was a combined sampling and sample pretreatment instrument, the role of which was to filter and dilute the samples before on-line determination by CE. The on-line procedures were optimized for simultaneous determination of anions as chloride, sulfate, oxalate, formate and acetate and for determination of cations as potassium, calcium, sodium, magnesium and traces of aluminium. The quantification was performed with external standard methods using the programs available in the commercial CE instrument. The concentrations of the ions were transferred by using a computerized transfer algorithm exporting the results from the analysis instrument to the process control unit. The developed on-line procedures were tested three times in paper and paperboard mills for 1 month at a time. Correlations were observed between the CE results and changes in the processes.

A direct mass spectrometry method utilizing reactive paper spray ionization was developed for sensitive cannabinoid quantitation in biofluid matrices. The ca. 2-minute sample measurements used on-paper derivatization to significantly increase paper spray mass spectrometry (PS-MS) positive ion mode sensitivity while minimizing sample preparation steps. Calibrations demonstrate high linearity, with R2 > 0.99 for (−)-trans-Δ9-tetrahydrocannabinol (THC) in oral fluid and 11-nor-9-carboxy-Δ9-tetrahydrocannabinol (THC-COOH) in urine. The limit of detection and lower limit of quantitation were 0.78 and 10 ng mL−1 for THC in oral fluid and 1.3 and 10 ng mL−1 for THC-COOH in urine, respectively. THC-COOH levels measured by reactive PS-MS in seven spiked human urine samples showed bias of −9.4 to 5.9%, and percent difference values of −16.8 to 9.8% in comparison with a reference LC-MS method. Based upon the method simplicity, validation experiments, sensitivity, and rapidity, we conclude that reactive PS-MS has potential applications for rapid cannabinoid drug testing in urine and oral fluid. [ABSTRACT FROM AUTHOR]

Diffuse reflectance spectroscopy can be successfully used for the quantitative determination of small amounts of pollutants like metals. The remission function was found to be linearly proportional to the concentration, when we applied the Kubelka-Munk equation. The color reactions of Cu(II), Co(II), and Ni(II) with dithiooxamide, were realised on filter paper. Reaction between Fe(III) and ammonium thiocyanate was realized on filter paper and gelatine matrix. All measurements were accomplished with a laboratory-constructed reflectometer. We have obtained a calibration curve by plotting the optical density of reflectance A(R) vs log of the mol l(-1) concentration. Limits of detection at the 10(-4) M level were estimated for all the compounds. Linear dynamic range extend over one order of magnitude and shows the potential of device for the quantitative analysis of environmental pollutants.

Cationized birch xylan was prepared and its use as a papermaking chemical was evaluated. The focus was on studying the effects of cationized birch xylan on the wet and dry strength of fine paper. The results of the laboratory experiments show that the addition of 3 percent of cationized birch xylan to birch kraft pulp improved the initial wet strength of the web by 30 percent compared to base stock at a solids content of 55%. Furthermore, the tensile stiffness of the wet web increased by approximately a third and the dry tensile strength improved by 26%, while the dry elastic modulus was not changed. The improvements in the strength properties were clear when compared to the base stock, but not as high as achieved with conventionally used cationized starch. The difference between the xylan and starch is most likely due to the shorter polymer chain length of the cationized xylan. [ABSTRACT FROM AUTHOR]

Highlights: [•] Improvement of the direct quantification with analytical pyrolysis. [•] Optimization of the chromatographic parameters after pyrolysis of cationic starch. [•] Quantification of cationic starches in cellulose matrixes. [•] Validation of the cationic starch quantification in paper samples. [ABSTRACT FROM AUTHOR]

[Display omitted] • GQD-DDT and GQD-MPA was synthesized using novel hydrothermal protocol. • GQD-DDT and GQD-MPA was used for the identification of cations using colorimetric and spectrophotometric assay. • GQD-DDT and GQD-MPA have well activity for ion sensing in aqueous solution. This study describes the synthesis of various types of thiolated-graphene quantum dots (GQDs) for the simultaneous multi-sensing of heavy metal ions using one-droplet microfluidic paper-based analytical devices (OD- µ PADs). For the first time, functionalized GQDs were synthesized and stabilized on the surface of hydrophobic fiber-glass with simple manufacturing and assembly strategy towards colorimetric chemosensing of ions including iron, copper, cobalt, mercury, chrome, manganese, and nickel. For this purpose, GQDs are functionalized by various organic species including cysteamine, decanethiol, and mercaptopropionic acid (MPA) towards specific electrostatic interaction with metal ions of Fe (II), Cu (II), Co(II), Hg (II), Mn (II), and Ni (II). Therefore, an innovative GQDs-based miniaturized chemo-system was proposed for the environmental analysis. Additionally, the results were confirmed using fluorescence spectrometry as an optical detection method. Finally, this simple and efficient colorimetric platform was used for facile metal ions detection in human urine models, and environmental fluids, which can provide a commercial device for sensing contaminants by non-professional users in biomedical/environmental mixture. As an economical technique, this platform presents a "mix-and-sense" system without dye (as a side substance) or chemical treatments. The low instrumental requirements, the color uniformity, and the disposability of OD- μ PADs approve the commercial application of the engineered ion-chemosensor. [ABSTRACT FROM AUTHOR]

A new approach for the chemical modification of the surface of paper based on the application of colloidal mixtures containing cationic starch and polyoxometalates on uncoated base paper is presented. Polyoxometalates with the Keggin-type structure and physical properties similar to those presented by coating pigments, namely H3PW12O40∙23H2O, H4SiW12O40∙24H2O, and K7PW11O39∙9H2O, have been used in order to improve the quality of inkjet printing. The analysis of the different samples by FTIRATR spectroscopy showed the presence of the polyoxometalates (and the cationic starch) on the top surface of the paper. In addition, the determination of surface energy parameters, namely the polar component (σsp) and the dispersive component (σsd) of the surface energy, by contact angle measurements revealed that, for the new samples, the polar component level was much higher than that of the uncoated base paper. The quality of inkjet printing, evaluated by parameters such as the gamut area and the optical density, was considerably improved by these surface treatments. [ABSTRACT FROM AUTHOR]

Rationale: Smoking is responsible for one in five deaths around the world. Thus, governments have been trying to reduce the number of active smokers by increasing taxes on products. This scenario creates a new problem by raising the consumption of illegally traded cigarettes, which are often seized and analyzed by police forces. Methods: Legal and illegal cigarette samples were extracted and analyzed using paper spray ionization mass spectrometry (PS-MS). The mass spectrometer was set to operate in full-scan positive ion mode to yield representative chemical profiles of each sample. The results were used to build a chemometric model using partial least squares discriminant analysis (PLS-DA) to discriminate between both sets of samples, i.e. legal and illegal. Results: The PS-MS procedure was fast, simple and efficient, yielding high-quality and reproducible mass spectra with a very good signal-to-noise ratio. Even though all samples displayed visually indistinguishable mass spectra, the PS-MS data handled by the PLS-DA approach furnished a model that reached sample classification with rates of 100% and 80% for the training and validation sets, respectively. Conclusions: A novel methodology was successfully developed associating the PSMS technique with chemometric analysis to differentiate between legal and illegal cigarettes. The PS-MS technique proved to be adequate for obtaining fingerprints of such types of samples despite high complexity, and a PLS-DA model was successfully constructed achieving 82.1% accuracy. [ABSTRACT FROM AUTHOR]

Oat β-D glucan was treated with 3-chloro-2-hydroxypropyl-trimethyl ammonium chloride (10%, 20%, 30%, or 50% of beta glucan) to obtain a range of cationic β-D glucan samples. The derivatization was confirmed by the results of Fourier transform infrared (FTIR) tests and elemental analysis. Addition of 1% cationic β-D glucan based on the mass of unbleached pine kraft fiber increased burst, tensile, and folding endurance properties of the resulting paper. Similar effects were observed at pH 5 and pH 8.5, showing that the system can be considered robust relative to typical acidic and alkaline papermaking conditions. The strength benefits were also observed in recycled sheets made by reslurrying paper prepared with cationic β-D glucan, even when the initial drying conditions had been severe. The beneficial results of cationization, which can be explained by a more hydrophilic nature and better retention, hold promise as a means of improving the strength properties of virgin paper. The treatment of the initial paper also can enhance the dry-strength performance when the fibers are recovered and used again. Application: Treating a hemicellulosic byproduct of oat processing to give it a positive charge can improve its effectiveness as a dry-strength agent for wet-end addition. [ABSTRACT FROM AUTHOR]

The objective of this study was to investigate the synthesis of zeolites from paper sludge ash, and to evaluate their applications for water purification to simultaneously remove NH4+ and PO43- in aqueous solution. Paper sludge ash had a low abundance of Si and a significant Ca content, due to the presence of calcite that was used as paper filler. Na2SiO3 was added to the NaOH solution to increase Si content in order to synthesize zeolites with high cation exchange capacity. The original ash without addition of Si yielded hydroxysodalite with a cation exchange capacity of ca. 50 cmol/kg. Addition of Si to the solution yielded Na-P1 (zeolite-P) with a higher cation exchange capacity (ca. 120 cmol/kg). The observed concentrations of Si and Al in the solution during the reaction explain crystallizations of these two phases. The product with Na-P1 could simultaneously remove NH4+ and PO43- from the solution between pH 4 and 9. [ABSTRACT FROM AUTHOR]

Accumulation of interfacial space charge in oil-paper interface is a critical issue in insulation diagnostics of transformers. This interfacial charge mainly accumulates due to the conductivity difference of oil and paper. Accumulation of interfacial charge leads to localized field enhancement, which further leads to partial discharges and acceleration in the aging of insulation. Therefore, from the point of view of transformer insulation diagnostics, assessment of interfacial charge is very important. However, it is not easy to estimate interfacial space charge behavior from the transformer diagnostics methods currently in use. In case of Polarization-Depolarization Current (PDC) measurement, a well known method for transformer condition monitoring, the effect of interfacial charge is reflected in the non-linearity of current response during polarization and de-polarization. During de-polarization process, a part of the interfacial charge accumulated during polarization period is absorbed by the electrodes producing a current, which is difficult to separate using conventional linear dielectric theory. In this paper, an attempt has been made to separate this current component from de-polarization current through considering charge de-trapping mechanism. Terming this current component as de-trapping current, its relationship with other parameters of transformer insulation is discussed. The developed methodology has been applied on several practical transformers. It was observed that the time constant of de-trapping current is related to the paper conductivity, oil conductivity, dissipation factor and age of the insulation. [ABSTRACT FROM PUBLISHER]

Here, we report a highly water‐soluble colorimetric and fluorescent pH probe that works in the pH range 0.2–3.0. The probe showed a rapid response, high stability, and excellent reversibility to acidity. Moreover, the fluorescence of probe was not influenced by the existence of high concentration of cations. The pKa of probe was calculated to be 2.25 ± 0.06. Furthermore, the pH test papers coated with the probe exhibited a distinct color change in acidic conditions. [ABSTRACT FROM AUTHOR]

Highlights: [•] Depending on xylan source, a different effect on paper strength was observed. [•] Cationization of xylan improved the strength enhancement. [•] A main influence on the paper strength was the absorption of cationic xylan. [•] Optimal absorption and strength were observed at a medium degree of cationization. [ABSTRACT FROM AUTHOR]

The non-stick properties of parchment papers are achieved by polydimethylsiloxane (PDMS) coatings. During baking, PDMS can thus be extracted from the silicone-coated parchment into the baked goods. Positive-ion direct analysis in real time (DART) mass spectrometry (MS) is highly efficient for the analysis of PDMS. A DART-SVP source was coupled to a quadrupole-time-of-flightmass spectrometer to detect PDMS on the contact surface of baked goods after use of silicone-coated parchment papers. DART spectra from the bottom surface of baked cookies and pizzas exhibited signals because of PDMS ions of the general formula [(C2H6SiO)n + NH4]+ in the m/z 800-1900 range. [ABSTRACT FROM AUTHOR]