Search

Vertical, organic, light‐emitting transistors (VOLETs) combine three of the four essential components of an active matrix lightemitting diode (AMOLED) pixel ‐ the drive transistor, the storage capacitor, and the OLED stack ‐ into a single, highly‐stable, selfemissive structure. VOLETs can be manufactured on amorphous silicon (a‐Si) thin‐film transistor (TFT) backplanes to enable lowcost AMOLED displays with improved brightness and lifetime characteristics. We report on the current status of VOLET development and prospective impact on the active‐matrix display industry. [ABSTRACT FROM AUTHOR]

Lengthened ion pathway in porous carbon cathode, especially under high mass loading and packing state, severely impeded the ion transport, thus leading to a far unsatisfactory energy/power out of Zn//C capacitors. Here, we report a novel kapok-derived quasi-2D thin-walled porous carbon tile (CT) with proper curvature and rich doping used as stacked bricks. Together with high conductivity single-walled carbon nanotubes, a porous yet relatively packed self-standing carbon cathode was constructed, which features a hierarchical ion path including short ion pathways inside thin-walled porous CTs and adequate channels "highways" caused by rational sub-micron interlayer spacing, thus leading to an excellent combination of rate and gravimetric/volumetric/areal performance at practical mass loading (12 mg cm−2). [Display omitted] • A porous thin-walled layered carbon tile with proper curvature was prepared as bricks. • Porous yet packed cathode feathers hierarchical paths for fast ion/charge transfer. • High rate and gravimetric/volumetric capacity remain in high loading cathode. • The areal capacity increases linearly with the mass loading of cathode. Long ion pathway inside large-sized carbon particle or stacked 2D assembly greatly limit the electrochemical performance of practical carbon cathode (>10 mg cm−2) in Zn//C capacitors. Highly porous activated carbon and holy graphene can alleviate such ion-transport issue, but usually suffer from a far lower packing density and severe restacking, respectively. Herein, a kapok-derived quasi-2D thin-walled microporous carbon tile (CT) with optimized curvature and rich doping was developed and used as bricks. Assisted with single-walled carbon nanotubes (SWNTs), a porous yet relatively packed paper cathode was constructed. The unique doped thin wall (∼700 nm) can effectively shorten the ion-penetration pathways from electrolyte deep into pore structure inside CTs, and thus enlarge ion-accessible surface areas. Combined with rational sub-micron interlayer spacing among proper-curved CTs and bridged-like SWNTs, the continuous ion/charge transport "highways" are fabricated. As a result, such self-standing carbon cathode delivers outstanding rate and gravimetric/areal performance (114 mAh g−1/1.37 mAh cm−2) without sacrificing volumetric capacity even at high mass loading (12 mg cm−2). [ABSTRACT FROM AUTHOR]

Copyright of Electrical Engineering & Electromechanics is the property of National Technical University, Kharkiv Polytechnic Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this paper, a voltage differencing buffered amplifier (VDBA)-based second-order sinusoidal oscillator (SO) configuration, which provides voltage output at low impedance, is proposed. The circuit employs single VDBA, three resistors and two grounded capacitors, which presume its easy monolithic integration with preferred circuit simplicity. The nonidealities of VDBA due to parasitic and tracking errors are taken into consideration to study the nonideal behavior of proposed SO. Mathematical modeling of phase noise is computed in the paper. Active and passive sensitivities are calculated for the proposed configuration and are found to be less than unity rendering circuit insensitive to component variations followed by phase noise study. The functionality of the proposed topology is validated through cadence virtuoso ADE spectre tool at 180-nm technology node. Experimental verification is executed through commercially available ICs AD844 by good results. The total harmonic distortion (THD) is found to be below 3.5%. The observed frequency of oscillation is found to be in close agreement with the theoretical values. The PVT and Monte Carlo statistical analyses are also carried out to confirm the sensitivity of the proposed SO. [ABSTRACT FROM AUTHOR]

[Display omitted] • Aramid-based energy storage capacitor was synthesized by a convenient method. • Electrical breakdown strength was optimized by the interface engineering. • Good dielectric constant thermal stability from RT to 300 °C was achieved. • Our finds promoted the energy storage capacitors in commercial use. Polymer-based dielectric energy storage capacitors show more potential than conventional rigidity ceramic-based capacitors. Recent studies were classified into two categories: the excellent room temperature performance in poly (vinylidene fluoride) (PVDF) systems and the enhanced thermal stability in polyimide-based systems. Only now, however, both of them are still far from commercial use because of their inferior heat resistance or poor processability. By adding BaTiO 3 (BT) particles in maturely used aramid nanofibers, we synthesized the aramid nanofiber (ANF)/BT-based flexible paper capacitors through a convenient industrialized technology in this work. Due to the intrinsic laminated structure of ANF and the uniform distribution of BT particles, the composite film with BT addition of 8 vol% exhibits outstanding dielectric thermal stability. With the help of the interfacial resistance in the organic–inorganic interface, which protected the ANF matrix from being breakdown too early by optimizing the electrical field distribution, a high and stable energy storage density of 6.70 J/cm3 was obtained in ANF/BT5. In addition, excellent energy storage frequency stability with ultrafast discharge speed was also achieved. This work offered a highly repeatable way to synthesize commercially used flexible capacitors, bridging the lab investigation and commercial use in high-power density energy storage polymers. [ABSTRACT FROM AUTHOR]

Supercapacitors have drawn numerous attentions in recent years since they can deliver relatively high power and energy densities. This article introduces an all-printed paper based surface mountable supercapacitor (SMS), which could withstand the reflow soldering process when integrated into microelectronic systems. The device was fabricated by screen printing and stencil printing processes, contributing to low cost and large-scale fabrication. Furthermore, building electronic devices on ubiquitous paper substrates had advantages of light weight, low cost, and eco-friendliness, etc. Based on activated carbon electrode material and ionic liquid electrolyte, the capacity of the supercapacitor could reach 14 mF at the device volume of 3.2 mm ? 2.5 mm ? 0.175 mm, besides, the specific volumetric capacity was superior than most of the commercial SMS devices. [ABSTRACT FROM PUBLISHER]

To effectively improve the power density and rate capability of layered double hydroxide (LDH) based supercapacitors, a hybrid supercapacitor (HSC) comprising of hierarchical ultrathin NiAl-LDH nanosheet arrays on carbon nanotube paper (CNP-LDH) is developed with porous graphene nanosheets as the negative electrode for the first time. SEM image shows that hierarchical NiAl LDH nanosheet arrays are assembled by numerous ultrathin nanosheets with thickness of a few to tens of nanometers. Remarkably, with an operating voltage of 1.6 V, the HSC possesses a high energy density of 50.0 Wh kg −1 at an average power density of 467 W kg −1 . Even at a fast discharging time of 3.9 s, a high energy density (23.3 Wh kg −1 ) could also be retained at a power density of 21.5 kW kg −1 . Moreover, the HSC exhibits cycling stability with a retention rate of 78% after 5000-cycle charge-discharge test at 5 A g −1 . The results inspire us to propose our high-performance CNP-LDH as a promising electrode for energy storage applications. [ABSTRACT FROM AUTHOR]

Graphite, an allotrope of carbon, is also a moderately good conductor of electricity. The shading pencil lead consists of graphite mixed with clay and, therefore, can conduct electricity, allowing one to construct and demonstrate different properties and the underlying concepts of circuit elements. The grade displayed on the pencil relates to the graphite-to-clay ratio, with higher B grades indicating a higher graphite-to-clay ratio. In this paper, the main objective is to show the dependence of resistance and capacitors on different physical parameters and to calculate the value of π electrically. The materials used in this activity are readily available, affordable, and suitable for demonstration purposes. The materials used to perform these activities are shading pencils of different grades, A-4 size papers, crocodile clips, and an LCR meter. [ABSTRACT FROM AUTHOR]

In this study, the multifunctionality of structural dielectric capacitor made by integrating graphene oxide paper into carbon fibre reinforced composite has been investigated. The study is based on an earlier work on the use of graphene oxide for dielectric material in the structural dielectric capacitor, in which electrical properties have been characterized. In this work, an in-depth study on electrical and mechanical properties of this kind of structural dielectric capacitor have been carried out. In addition, the multifunctional efficiency of structural dielectric capacitors were evaluated and compared with existing structural dielectric capacitors. Through experiments, it is revealed that both electrical and mechanical properties of the structural dielectric capacitors were significantly enhanced by interleaving a graphene oxide paper in the middle of composite. Therefore, the multifunctional efficiency of this kind of structural dielectric capacitors has been ultimately improved, indicating the excellent potential of graphene oxide paper in the development of multifunctional materials for energy storage, potentially for high-strength required applications, such as electric vehicles and unmanned aerial vehicles. [ABSTRACT FROM AUTHOR]

Electronic capacitors were constructed via hand-printing on paper using pencil graphite. Graphite traces were used to draw conductive connections and capacitor plates on opposing sides of a sheet of standard notebook paper. The paper served as the dielectric separating the plates. Capacitance of the devices was generally < 1000 pF and scaled with surface area of the plate electrodes. By combining a pencil-drawn capacitor with an additional resistive pencil trace, an RC low-pass filter was demonstrated. Further utility of the pencil-on-paper devices was demonstrated through description of a capacitive force transducer and reversible chemical sensing. The latter was achieved for water vapor when the hygroscopic cellulose matrix of the paper capacitor’s dielectric adsorbed water. The construction and demonstration of pencil-on-paper capacitive elements broadens the scope of paper-based electronic circuits while allowing new opportunities in the rapidly expanding field of paper-based sensors. [ABSTRACT FROM AUTHOR]

The necessity of drying the graphene oxide suspension (GOsus) using Hummer's Method to produce graphene oxide (GO) powder was studied. The undried GOsus was compared to the dried GO. The GO materials were used as Pt supports via NaBH4 reduction for O2 reduction. XRD patterns showed similar d-spacing in both while the half-cell tests of the Pt/rGOsus and Pt/rGO catalysts were similar. GOsus film, deposited onto Toray Carbon Paper and electrochemically reduced in aq. H2SO4 was tested as a capacitor. The suspension and dried graphene-based capacitor showed similar XRD and XPS patterns and the erGOsus capacitor displayed increased capacitance. [ABSTRACT FROM AUTHOR]

The identification and quantification of chemicals play a vital role in evaluation and surveillance of environmental health and safety. However, current techniques usually depend on costly equipment, professional staff, and/or essential infrastructure, limiting their accessibility. In this work, we develop paper-based capacitive sensors (PCSs) that allow simple, rapid identification and quantification of various chemicals from microliter size samples with the aid of a handheld multimeter. PCSs are low-cost parallel-plate capacitors (~$0.01 per sensor) assembled from layers of aluminum foil and filter paper via double-sided tape. The developed PCSs can identify different kinds of fluids ( e.g. , organic chemicals) and quantify diverse concentrations of substances ( e.g. , heavy metal ions) based on differences in dielectric properties, including capacitance, frequency spectrum, and dielectric loss tangent. The PCS-based method enables chemical identification and quantification to take place much cheaply, simply, and quickly at the point-of-care (POC), holding great promise for environmental monitoring in resource-limited settings. [ABSTRACT FROM AUTHOR]

A capacitor formed of fluid-impregnated paper metalized on one side and a polymer film results in a relaxation peak caused by the much more rapid polarization of the dielectric fluid impregnated paper relative to the polymer film. This results in the capacitance being a function of frequency, with a substantial increase in capacitance at very low frequencies. A theory for such a capacitor is developed and compared with measurements on actual capacitors with relatively good agreement. The implications of the theory for discharge current and discharge efficiency are discussed. [ABSTRACT FROM AUTHOR]

In this paper, we designed a novel multicolor electrochromic (EC) device having hybrid capacitor electrochromic device based on 4,4 '‐biphenyl dicarboxylic acid diethyl ester and phenothiazine molecule with carbon electrode. The EC properties of the device were analyzed and discussed for the possibility to multicolor representation. [ABSTRACT FROM AUTHOR]

This paper presents a 14‐Gb/s dual mode receiver with MIPI D‐PHY and C‐PHY interfaces for mobile display drivers. To reduce size overhead from the dual mode interfaces, we propose the termination circuit that can share 50‐Ω terminations and common‐mode capacitors while maintaining a perfectly matched load balance. The proposed dual mode receiver supports up to 14 Gb/s total bandwidth in each interface mode, resulting in broad compatibility with application processors. A mobile display driver using the proposed dual mode receiver is fabricated in a 28‐nm high‐voltage CMOS process and verified up to 3.5 Gb/s per lane in the D‐PHY mode and 2.2‐Gs/s per lane in the C‐PHY. [ABSTRACT FROM AUTHOR]

Power capacitors are highly reliable due to their completely enclosed configuration. They are relatively trouble-free over the long term. However, their dielectric strength can be reduced due to some stresses, including overvoltage application or thermal degradation of the insulation material during long periods of operation; these events can result in dielectric breakdown of capacitors in extreme cases. Since almost all power capacitors with oil-impregnated paper have been operated for more than twenty years, some kind of failure should be expected. To prevent these incipient accidents, it is important to examine the insulation deterioration mechanism and evaluate the degree of deterioration before capacitor breakdown. To establish a diagnostic method of deterioration of the capacitors with oil-impregnated paper, we have conducted thermally and electrically accelerated deterioration tests and investigated the changes of their characteristics. Based on the experimental results we obtained, it can be concluded that the behavior of the oil-dissolved gases can be used as a useful index to diagnose the insulator deterioration of these capacitors. [ABSTRACT FROM AUTHOR]

Measurements of capacitors made with paper sheets reveal a significant decrease in capacitance with increasing frequency from 10 to 100,000 Hz, offering a simple demonstration of complex dielectric phenomena using common equipment. [ABSTRACT FROM AUTHOR]