Search

Power utilities worldwide commonly use the radial distribution system because of its advantages of being simple in structure and having relatively inexpensive installation costs. It has a disadvantage in that its power supply reliability is low because the load side of the fault section will suffer from an outage in the event of a fault in the system. However, recently, with ICT (Information and Communication Technologies) development, system reliability is required to be high as the outage-susceptible loads increase. In addition, the increase in the connection of distributed resources such as renewable energy and electric vehicles is making it impossible to predict the power flow and reducing line utilization. Therefore, a loop power distribution system is proposed as a measure to solve this problem. Because all buses (nodes) in a loop distribution system have two or more power supply routes, they are more reliable than the radial system. It allows them to improve line utilization by connecting lines with different load peak times. However, in the case of a fault in the loop distribution system, the fault current is supplied from both directions, making it impossible to properly isolate the fault section with the protection method of the conventional distribution system. The permissive overreach transfer trip (POTT) method using communication to compensate for the limitations of conventional protection devices, and the other method using directional distance relay, is proposed. However, these methods operate by determining the direction of the fault current but have a disadvantage. It is difficult to detect a fault due to the effects of ground faults and distributed generation (DG) occurring in other lines. Therefore, in this paper, we propose a protection coordination algorithm that uses the negative-sequence component of voltage and current that occur when an unbalanced fault occurs, rather than the determination of the directionality and use of communication. To validate this, we configured a system using PSCAD/EMTDC (Manitoba Hydro International Ltd., Winnipeg, Manitoba, Canada), a system analysis program package and verified the results depending on the type of faults with the proposed algorithm.

Generally, the fault current supplied by inverter-based renewable energy sources (IBRES) and electrical storage systems (ESS) is about 1.2 to 2 times their rated current and much lower than synchronous generators because the former acts as a current source and the latter acts as a voltage source. A conventional power system in a small island is composed of only synchronous generators and protected from short circuit faults using an overcurrent relay (OCR). However, in the remote microgrid with IBRES, ESS, and synchronous generators, the fault current varies depending on the configuration of generation sources. Namely, the fixed OCR protection method cannot protect microgrids from short circuit faults. This paper proposes an adaptive protection method to protect the microgrid from faults by actively changing the OCR setting according to the state of the generator source combination. A microgrid with ESS and a synchronous generator is modeled and simulated through PSCAD/EMTDC software to validate the proposed adaptive protection method.

As the penetration of different types of renewable energy sources (RES) and energy storage systems (ESS) increases, the importance of stability in AC microgrid is being emphasized. Especially, RES and ESS which are operated using power electronics have difference in output characteristics according to control structures. When faults like single-line-to-ground fault or islanding operation occur, this means that a fault should be interpreted in different way. Therefore, it is necessary to analyze fault characteristics in AC microgrid in case of grid-connected mode and standalone mode. In this paper, the fault analysis for AC microgrid is carried out using PSCAD/EMTDC and an overvoltage problem and the countermeasures were proposed.

In Korea, high generation cost and environmental pollution are also discussed at island off-grid. In this situation, remote microgrid (MG) can be solution to solve the problems. Remote MG is small power system, which consists of renewable sources, energy storage system, and load. It is possible to reduce generation cost by introducing remote MG into island areas. KEPCO (Korea Electric Power Corporation) is also proceeding study on remote MG and doing project about remote MG. KEPCO had designed demonstration site for remote MG and constructed the site at island named ‘Geocha-Island’ which is located in south-western side of Korea. This study deals with the system design by economic evaluation. Secondly, construction of the site is introduced. Finally, operation strategy of the system is introduced.

In island and backcountry areas, electrical power is usually supplied by diesel generators. It is difficult for small scale diesel generators to have an economy of scale owing to the usage of fossil fuels to produce electricity. Also, there is a problem of carbon dioxide emissions that brings some environmental pollution to the entire region of the area. For solving those, this paper proposes a design method of autonomous micro-grid to minimize the fossil fuels of diesel generator, which is composed of diesel generator, wind turbine, battery energy storage system and photovoltaic generation system. The proposed method was verified through computer simulation and micro-grid operation system.

To save on the island area's power supply cost and protect the clean environment, the Isolated MicroGrid is being duly considered. Consisting of the Wind Turbine Generator (WT), photovoltaic generator, battery system, back-up diesel generator, etc., Isolated MicroGrid, which usually uses the inverter to maintain voltage and frequency of the system, is very weak in terms of voltage and frequency stability compared to the large-scale electrical power system. If wind turbine generator is applied to this weak power system, it could experience many problems in terms of maintaining its voltage and frequency. In this paper, the measurement result of voltage and frequency is presented for MicroGrid, which consists of the Wind Turbine Generator adopting the induction generator and the battery system. MicroGrid’s voltage waveform distortion and Wind Turbine Generator’s output oscillation problems are analyzed using PSCAD/EMTDC. Based on the analyzed result, the importance of type and capacity choice has been suggested in case the Wind Turbine Generator is applied to the Isolated MicroGrid.

This paper proposes a new grid-tied power converter for battery energy storage, which is composed of a 2-stage DC-DC converter and a PWM inverter. The 2-stage DC-DC converter is composed of an LLC resonant converter connected in cascade with a 2-quadrant hybrid-witching chopper. The LLC resonant converter operates in constant duty ratio, while the 2-quadrant hybridswitching chopper operates in variable duty ratio for voltage regulation. The operation of proposed system was verified through computer simulations. Based on computer simulations, a hardware prototype was built and tested to confirm the technical feasibility of proposed system. The proposed system could have relatively higher efficiency and smaller size than the existing system.

Various DSM (Demand Side Management) programs have been developed and carried out to use the limited energy resources of human-beings reasonably. LED lighting is one of essential DSM programs and the development of technologies is ongoing vigorously. Recently, one-person households have been increased and the electricity consumption pattern is different with conventional households because residents live as a single. On the other hand, owners of the one-person households tend to not prefer to install high efficient appliances due to the cost increasement. Therefore, the existing DSM subsidy programs should be revaluated so that the owners decide to install high efficient appliances.

MicroGrids are small power supply system located on-site that can supply both the electricity and the hot-water simultaneously. MicroGrid system that consists of Distributed Energy Resources system, such as wind, solar, fuel-cell and co-generation, has been developed greatly during the last 10 years. It's concept assumes a cluster of loads and microsources operating as a single controllable system that provides a new paradigm for defining the operation of distributed generation. For example this cell could be controlled as a single dispatchable load, which can respond in seconds to meet the needs of the transmission system. It can be also designed to meet their special need; such as, enhance local reliability, reduce feeder losses. This paper introduces the case study of engineering to construct Microgrid with actual loading in KEPRI

The grid-interconnected microgrid can be able to operate with and without the utility microgrid to supply electricity. when the microgrid operates in grid-connected mode, the frequency of the microgrid synchronizes with the system frequency. In this case, the frequency of the microgrid has small variation which is able to change the output of distributed generation with a droop controller. Thus, the small variation of frequency can make the distributed generation generate unnecessary electricity consistently. In this paper, we propose a frequency droop control with a dead band so as to prevent the distributed generations from generating unnecessary output while in grid-interconnected mode. In addition, a distributed generation can have a restoration control to restore the frequency changed by a droop control as a rated frequency. Also, we state the problem of restoration control with a dead band, and propose its solution when the microgrid operates in stand alone mode. We simulate the proposed droop control using PSCAD/EMTDC to verify the validity of the control.

This paper propose the advanced topology of UPQC, its DC link is connected with Lithium battery, to compensate the momentary interruptions. The proposed system can be operated as UPS mode using the parallel inverter, which control the charge or discharge of battery, in case of the interruption. We dvelop 100kVA UPQC using the proposed topology to rise the power quality and the reliability of Microgrid. We verify its usefulness through voltage compensation test, UPS operation test and etc. using Microgrid test facility.

A microgrid is a micro-power system composed of local distributed generators, energy storage systems, loads, and other components in a local power network. Because renewable energy sources show relatively large output power variation, the integration of distributed generators in a microgrid often requires the installation of a large-scale energy storage system. The energy storage system is connected to a local AC bus via the DC/AC converter with an output inductor-capacitor (LC) filter. The energy storage system power converters generally form the local AC bus voltage. This grid-forming operation requires fast and robust voltage control to properly maintain a stable energy flow and high power quality in the local AC bus. In this paper, two major voltage control schemes—double-loop control and direct voltage control—are analytically compared, and their effects on the power quality of the microgrid are illustrated. The dynamic performance is compared through simulations and experimental results.

In a conventional distribution system, protection algorithms are designed to operate on a unidirectional high fault-current level. In a microgrid, a fault current from distributed generation (DG) may bring about a relay malfunction because of the bidirectional and relatively small fault current. Therefore, the conventional protection scheme is not applicable to microgrids and a new protection method must be developed. In this paper, two protection coordination algorithms which can be applied for facility and secondary microgrids are proposed, respectively. The proposed protection algorithms eliminate faults not by the EMS signal but by directional relays. Moreover, this makes the algorithms flexible regardless of the types and numbers of DG. The proposed protection algorithms were simulated at the KEPCO RI Microgrid Demonstration Site.

Microgrid is a new electrical energy system that composed of various generators, renewable energy, batteries and loads located near the electrical customers. When Microgrid is interconnected with large power system, Microgrid don`t need to control the frequency. But in case of the outage or faults of power system, Microgrid should control the frequency to prevent the shutdown of Microgrid. This paper presents the frequency control methods using the droop function, being used by synchronous generators and EMS(Energy Management System). Using droop function, two battery systems could share the load based on locally measured signals without any communications between batteries. Also, we suggest that EMS should control the controllable distributed generators as P/Q control modes except batteries to overcome the weakness of droop function. Finally we suggest the two batteries systems to prolong the battery`s life time considering the economical view. The validation of proposed methods is tested using PSCAD/EMTDC simulations and field test sites at the same time.

The microgrid concept assumes a cluster of loads and microsources operating as a single controllable system that provides a new paradigm for defining the operation of distributed generation. This system can be operated as both grid-connected mode and islanded mode. In other words, the microgrid can be operated to meet their special need; such as economics in steady state and local reliability in islanded mode due to the grid fault. This paper presents the AGC (Automatic Generation Control) method for microgrid with EMS (Energy Management System).

PCS(Power Conditioning System) is the necessary component in Microgrid, composed of multiple distributed generators and energy storage system. In this paper, the functions of PCS are defined and 10[kW] PCS for PV and BESS are developed. To apply PCSs to Microgrid, this paper presents a 3-phase inverter with the decoupling current controller, voltage controller and DPLL control system. PCSs were applied to 120[kW] pilot plant and its performance tests were carried out. Test results of PCS at each operation mode show stable in Microgrid.

Penetration of distributed generator(DG) to power distribution system can cause malfunction of existing protection schemes. Because grid interconnected DG can contribute fault currents and make bidirectional current flows on the system, fault contributions from DG can cause an interference of protection relay operation. Therefore, over current protection device of the distribution system with DGs need directional protection schemes. In this paper, improved directional protection algorithms are proposed for the distribution system with DG considering their fault characteristics. And than, these directional protection algorithms are tested and validated in various fault conditions. From the simulation results, it can be seen that the proposed directional protection algorithms are practically efficient for the radial distribution system with DG.

MG(Microgrid) is a small power supply system located on-site that can supply both the electricity and the hot-water simultaneously. Engineering S/W is requested to construct Microgrids economically. We developed Engineering S/W that can combine DERs (Distributed Energy Resources) most economically using the linear programming and estimate of the economic. Developed S/W was programed using GAMS(General Algebraic Modeling System) and it is composed of the optimal DER combination module and forecasting module of renewable energy`s output. We embody it based on MS Excel considering the user`s convenience and we show its validity through a case study. We think that developed S/W will be very useful for planning MGs and energy supply.

It is expected that distribution system, interconnected with wind turbines, would experience the voltage problem due to WT`s output. But most papers just consider this problem using the simulation or the theory only. In this paper, we verify this problem through the measurement at the distribution system and wind turbine. We explain the method for voltage management at distribution system. And we verify that the voltage of D/L interconnected with WTs could not be maintained properly using pole transformer`s tap only. We consider some method to solve this problem and we propose the installation of SVR(step voltage regulator). Finally we show this method`s validity through the simulation.

Power system of Jeju is interconnected to the mainland using HVDC and that is also interconnected two wind farms. Control of Jeju power system will be difficult if HVDC is disconnected or HVDC is overhauled under large scale wind farms interconnected. We measured and analysed the power quality of two substation and two wind farms to assess that wind farms and HVDC overhaul have an effect on Jeju system or not during the HVDC overhaul. We found that the frequency of Jeju system is very unstable and the voltage distortion excess the limitation. Harmonic currents of wind farms flew into Jeju system in proportion to the power of wind turbine. And the voltage of nearby distribution line was distorted by power of wind turbine when the amount is more that 3,000[kW].

This paper presents an interconnection device between DNO and small scale DERs of customers. It can link DERs more economically and improve the power quality for customers owing to prevent power failure by independent operation in case of power failure in DNO network and trade the electricity with DNO. In addition it can send information on the condition of the customer electricity network. So DNO can operate their distribution network efficiently. For the customer it can connect DERs efficiently and reduce installation spaces. In this device each power converter of DER connected to DC link and one bidirectional inverter wired to DC link. A static transfer switch (STS) was installed so that customers can prevent power failure by islanding operation during the DNO network failure. An intelligent electronic device (IED) was installed so that power and information can be exchanged with DNO or nearby customers and the protection control can be done to satisfy all the current standards for DERs. (4 pages)

As Smart Grid is being applied to distribution power system, SDMS (Smart Distribution Management System) has been developed for distribution power system management. Distribution power system has been changed from radial system to closed loop or mesh systems due to connection of distributed generation growth. Data from distribution equipments which are installed at distribution line must be accurate for the performance of SDMS. This study analyzes the voltage measurement data from distribution equipment. However, the results of the analysis confirm to have some errors in voltage measurement data from distribution equipment. These errors come from aging of voltage sensor in distribution equipment and inaccurate data transfer to FRTU through the controller. The main problem is not to assess the voltage measurement data after first installation of distribution equipment at the distribution line. This paper shows the voltage measurement accuracy assessment system that is to evaluate the voltage measurement data from distribution equipment on liveline to solve the problem. This system had a field test to check its performance. It will be used to assess the performance of distribution equipments and smart distribution equipments. (4 pages)

This paper proposes a smart switch panel (SSP) that can link distributed generations more economically and actively to improve power quality for customers, prevent power failure through independent operation in case of power failure in electric power systems (EPS), and trade electricity with Smart Grid operation systems as they become more widespread. For the economical interconnection of distributed generations and to reduce installation spaces, a power converter was installed in the switch panel, and the power converter was proposed in a form wherein diverse distributed generations share the DC link and inverter. A static transfer switch (STS) was installed so that customers can prevent power failure through independent operation even in case of EPS failure. An intelligent electronic device (IED) was installed so that power can be exchanged with EPS or nearby customers and to enable protection control so that all current standards for the interconnection of distributed generations are met.

The grid-interconnected Microgrid must be able to operate without the utility's grid to supply electricity in case of outage. To operate in standalone mode, the Microgrid must control electricity demand or supply to maintain the frequency. The Microgrid EMS (Energy Management System) could control supply and demand with the AGC (Auto Generation Control) function using a communication line. Note, however, that the period of AGC is too slow to maintain the frequency if there is rapid variation in loads or generation. Moreover, the transition of operation mode could fail if there is too much power flow at PCC (Point of Common Coupling). In this paper, we propose a method of improving the stability of the grid-interconnected Microgrid using BESS (Battery Energy Storage System) and super capacitor. The cooperative control method between BESS and super capacitor uses droop, which is used at the generator. BESS could operate as UPC (Unit Power Control) or FFC (Feeder Flow Control) depending on Microgrid's operation strategy. We simulate the cooperative control method using PSCAD/EMTDC to verify the validity of the method. As a result, Microgrid's stability is improved using the cooperative control method, and the life span of BESS could be prolonged.