Search

Laser-induced graphene (LIG) technology featuring low-cost, high-efficiency and scalability has presented great advantages in micro-supercapacitors (MSCs) fabrication. However, the limited capacitance of LIG based MSCs is still hindering their further development. Herein, we introduce joule heating as a critical in-situ treatment merged with the assembly of laser-induced graphene paper based MSCs (LIGP-MSCs) toward capacitive enhancement. By increasing heating-treatment temperature from ∼20 to 500 °C, the number of nanopores in LIGP continuously increases, attributed to the gradual decomposition of amorphous carbon components. The resulting joule-heated LIGP (J-LIGP) with improved specific surface area (160.97–533.49 m2/g) and pore volume (0.179–0.553 cm3/g) as well as superhydrophilic surface is highly suitable to be employed as J-LIGP-MSCs microelectrodes. By investigating process dependent performance, the J-LIGP-MSCs heated at 500 °C for 60 min delivers a significantly improved specific areal capacitance (CA) of 13.71 mF/cm2 at 10 mV/s, which is approximately six-fold higher than that of unheated LIGP-MSCs. By further exploring and optimizing the process efficiency, J-LIGP-MSCs with a CA of 12.61 mF/cm2 has been achieved by 550 °C heating for only 5 min. Along with superior mechanical flexibility, cyclability and structural modularity, the proposed in-situ joule heating treatment is finally proved to be a universal approach for consistently enhancing the CA of LIG based MSCs processed under various chemical modifications.

Time-limited exposure of electrode-free optically rewritable electronic paper is essential for applications, but performance characteristics can be modest. In this study we investigate whether imag...

We demonstrated the thermally robust reduced graphene oxide (rGO)/boron nitride nanotube (BNNT) papers and their application in electromagnetic interference shielding. In order to overcome the thermal durability shortcomings of electromagnetic wave shielding paper based on rGO nanomaterial, rGO/BNNT electromagnetic interference (EMI) shielding paper having excellent thermal durability could be manufactured using BNNT nanomaterials having excellent chemical and thermal stability at high temperature. With the addition of a little BNNT, the durability against temperature can be increased by more than two times while there is little reduction in EMI performance.

In this study, Taguchi experimental design was used to the optimize operating parameters for the degradation of paper mill effluent using electrochemical (EC) process with two-dimensional concentric aluminum tube electrodes (CATE). For this purpose, four significant experimental factors were used in four levels pH (6–9), electrolysis time (10–40 min), voltage (6–12 V) and surface area (357–624 cm(2)). The process parameters were optimized, through performing L16 orthogonal array of Taguchi technique, for the removal of chemical oxygen demand (COD) and turbidity. The percent COD and turbidity reductions were transferred into an accurate S/N ratio for a larger value is the better (LBT) response. The study presents a unique method of finding optimum combination of process parameters to illustrate their effect on the turbidity and COD reduction. The treatment conditions for the maximum elimination of the pollutants were second level of pH (7), third level of ET (30 min), fourth level of voltage (12 V) and second level of surface area (446 cm(2)). The confirmation experiment results were within the confidence intervals (CI) indicating an acceptable agreement between predicted and observed values. Based on the p-values, the electrolysis time and voltages were found to be the most significant factors for both COD and turbidity reduction. The findings of research indicated, that the Taguchi method can be used successfully for the treatment of paper industry effluent by electrochemical technique.

The work aims to explore a microscopic observation system of paper surface and achieve high-precision stereoscopic observation with detail characterization of paper surface morphology. Based on the DT-400E precision program-controlled three-dimensional translation stage and KEYENCE LJV-7200 two-dimensional laser scanner, the hardware parts of our own system are developed to scan and transmit point cloud data of paper surface morphology to the computer. The corresponding system software will automatically process the point cloud data acquired from the laser scanner and generate the corresponding vivid 3D model and height histogram. This system scans and characterizes four different types of paper samples, allowing the human eye to visually distinguish the differences in surface morphology as well as automatically calculate the numerical differences in paper surface morphology parameters. The results of the applicability test show that the system is highly efficient in acquiring, observing, and evaluating the topography of the paper surface. The system can not only predict the paper surface quality of printed paper, but can also be extended to the evaluation of 3D printed surfaces.

Flexible paper-based sensors may be applied in numerous fields, but this requires addressing their limitations related to poor thermal and water resistance, which results in low service life. Herein, we report a paper-based composite sensor composed of carboxylic carbon nanotubes (CCNTs) and poly-m-phenyleneisophthalamide (PMIA), fabricated by a facile papermaking process. The CCNT/PMIA composite sensor exhibits an ability to detect pressures generated by various human movements, attributed to the sensor's conductive network and the characteristic "mud-brick" microstructure. The sensor exhibits the capability to monitor human motions, such as bending of finger joints and elbow joints, speaking, blinking, and smiling, as well as temperature variations in the range of 30-90 °C. Such a capability to sensitively detect pressure can be realized at different applied frequencies, gradient sagittas, and multiple twists with a short response time (104 ms) even after being soaked in water, acid, and alkali solutions. Moreover, the sensor demonstrates excellent mechanical properties and hence can be folded up to 6000 times without failure, can bear 5 kg of load without breaking, and can be cycled 2000 times without energy loss, providing a great possibility for a long sensing life. Additionally, the composite sensor shows exceptional Joule heating performance, which can reach 242 °C in less than 15 s even when powered by a low input voltage (25 V). From the perspective of industrialization, low-cost and large-scale roll-to-roll production of the paper-based sensor can be achieved, with a formed length of thousands of meters, showing great potential for future industrial applications as a wearable smart sensor for detecting pressure and temperature, with the capability of electric heating.

Organic electrochemical transistors (OECTs) have attracted great interest in the last few years as biochemical sensors due to their outstanding analytical performance, versatility, stability, and e...

Detecting the concentration of free chlorine is important for monitoring the quality of water. In this study, we report a nanohybrid paper-based chemiresistive sensor that can be used with smartphones to detect free chlorine ions. The sensor was fabricated using a simple and standardized coating process. The graphene and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) nanohybrid paper-based sensing device exhibited a more stable and intuitive response to free chlorine than that exhibited by the device using only PEDOT:PSS. The nanohybrid paper-based sensor was sensitive to free chlorine concentrations in a linear range of 0.1-500 ppm, and the limit of detection was 0.18 ppm. The sensor showed specificity for free chloride ions and detection capability in samples. The sensor was integrated as a module with an electric readout system, and the measured signals and results could be displayed in real time on a smartphone. Therefore, the proposed sensing platform is suitable owing to its portability, low cost, ease of use, and capability for on-site water quality measurement.

Abstract Tissue paper softness relies on two major factors, the bulk softness, which can be indicated by the elasticity of the sheet, and surface softness. Measurement of surface softness is complicated and often requires a multi-step process. A key parameter defining surface softness is the topography of the surface, particularly the crepe structure and its periodicity. Herein, we present a novel approach to measure and quantify the tissue paper surface crepe structure and periodicity based on the detection of waviness along the sample using laser scanning confocal microscopy (LSM) and X-ray tomography (XRT). In addition, field emission scanning electron microscope (FESEM) was used to characterize the tissue paper surface. We demonstrate that surface topography is directly correlated to the erosion of the doctor blade, which is used to remove the dry tissue paper from the Yankee cylinder. Because of its accuracy and simplicity, the laser confocal microscopy method has the potential to be used directly on the production line to monitor the production process of the tissue paper. XRT revealed more structural details of the tissue paper structure in 3D, and it allowed for the reconstruction of the surface and the internal structure of the tissue paper. Graphic abstract

Flexible thin-film solar cells with high weight-specific power density are highly desired in the emerging portable/wearable electronic devices, solar-powered vehicles, etc. The conventional flexible metallic or plastic substrates are encountered either overweight or thermal and mechanical mismatch with deposited films. In this work, we proposed a novel substrate for flexible solar cells based on graphene paper, which possesses the advantages of being lightweight and having a high-temperature tolerance and high mechanical flexibility. Thin-film amorphous silicon (a-Si:H) solar cells were constructed on such graphene paper, whose power density is 4.5 times higher than that on plastic polyimide substrates. In addition, the a-Si:H solar cells present notable flexibility whose power conversion efficiencies show little degradation when the solar cells are bent to a radius as small as 14 mm for more than 100 times. The application of this unique flexible substrate can be extended to CuInGaSe and CdTe solar cells and other thin-film devices requiring high-temperature processing.

Reflective liquid crystal displays are attracting attention as portable information systems because of zero- or extremely low power consumption. In this study, we deal with an electrode-free reflec...

Electromagnetic interference (EMI) shielding materials with high performance and low density are urgently needed with the rapid development of electronic communications. In this work, tuning solid–air interface of graphene paper was carried out to enhance multiple reflections of incident electromagnetic waves for high-performance EMI shielding. The large amount solid–air interface (57.8 m2 g−1) endowed the porous graphene paper with a high EMI shielding effectiveness (SE) of 31.0 dB, 50% enhancement from its counterpart of solid graphene paper. This porous graphene paper also showed an ultralow density of 0.02 g cm−3, an 18.5-fold decrease from its counterpart of solid graphene paper. Moreover, the EMI SE of obtained graphene papers exhibited proportional relationship with their specific surface area, further confirming the vital role of solid–air interface in the enhancement of EMI shielding. This work quantitatively demonstrates the significance of solid–air interface area for enhancing the EMI shielding performance and proposes an efficient guideline for the design of high-performance and low-density EMI shielding materials.

The development of renewable energy sources minimizes the burning of fossil fuels for clean and green environment. Electrochemical energy storage/conversion device pays a way towards sustainable development that concludes an emerging field in the trends of the research community. Prominently, the functional materials with suitable structure and property determine the performance and durability of the devices. In recent times, graphene with its tremendous properties play a major role in electrochemical energy device applications. Meanwhile, the graphene-based electrodes were fabricated by various coating techniques on existing electrodes that utilized for energy device fabrication. Apart from these, it is also fabricated in a paper like a form (self-supported or free-standing) with its remarkable high conductivity, flexibility, robustness and electrochemical behavior which have been nominated for fabrication of flexible energy devices. Paper-like electrodes become an emerging field to fabricate a light-weight and flexible electronic devices for future prospects. Thus, we have summarized a synthetic strategy of graphene paper and its properties that potentially focused on flexible device fabrication in both the energy storage and conversion system. Hence, this review boosts up the forthcoming researchers to enhance the device performance with interrelating free-standing graphene and other host material.

This paper describes the use of fused deposition modeling (FDM) printing to fabricate paper-based analytical devices (PAD) with three-dimensional (3D) features, which is termed as 3D-PAD. Material depositions followed by heat reflow is a standard approach for the fabrication of PAD. Such devices are primarily two-dimensional (2D) and can hold only a limited amount of liquid samples in the device. This constraint can pose problems when the sample consists of organic solvents that have low interfacial energies with the hydrophobic barriers. To overcome this limitation, we developed a method to fabricate PAD integrated with 3D features (vertical walls as an example) by FDM 3D printing. 3D-PADs were fabricated using two types of thermoplastics. One thermoplastic had a low melting point that formed hydrophobic barriers upon penetration, and another thermoplastic had a high melting point that maintained 3D features on the filter paper without reflowing. We used polycaprolactone (PCL) for the former, and polylactic acid (PLA) for the latter. Both PCL and PLA were printed with FDM without gaps at the interface, and the resulting paper-based devices possessed hydrophobic barriers consisting of PCL seamlessly integrated with vertical features consisting of PLA. We validated the capability of 3D-PAD to hold 30 μL of solvents (ethanol, isopropyl alcohol, and acetone), all of which would not be retained on conventional PADs fabricated with solid wax printers. To highlight the importance of containing an increased amount of liquid samples, a colorimetric assay for the formation of dimethylglyoxime (DMG)-Ni (II) was demonstrated using two volumes (10 μL and 30 μL) of solvent-based dimethylglyoxime (DMG). FDM printing of 3D-PAD enabled the facile construction of 3D structures integrated with PAD, which would find applications in paper-based chemical and biological assays requiring organic solvents.

In recent era of modern and bendable technology, energy dearth arises as a paramount subject around the globe with a dire demand of flexible and lightweight energy storage devices. This study targets fabrication of reduced graphene oxide (rGO) and utility of abundantly available, cost effective, and environment friendly lignocelluloses (LC) fibers extracted from Carica papaya source, as a binder to bind active material (rGO) as robust and compact paper sheet. Fabricated samples were analyzed by X-ray diffraction for crystallographic analysis, Scanning electron microscopy, Transmission electron microscope for morphology, Fourier transform infrared spectroscopy for structural bonding, and Raman spectroscopy for vibrational modes. Robust and bendable rGO/LC paper electrode was tested for energy storage application by employing in different characterizations, i.e., cyclic voltammetry for capacitive behavior, galvanostatic charge–discharge for symmetric EDLC, and electrochemical impedance spectroscopy for resistive charge kinetics, respectively. rGO/LC composite sheet employed as working electrode in 3-electrode CV measurements and revealed specific capacitance of 591 F/g at a scan rate of 5 mV/s by keeping the undistorted shape of voltammograms at higher scan rates which present it as a suitable candidate for modern flexible and energy storage devices. rGO/LC-based symmetric cell revealed the highest specific capacitance of 228 F/g at applied current density of 0.1 A/g, the energy density of 6.3 Wh/kg, and power density of 129 W/kg, respectively. rGO/LC-based symmetric cell confirmed the cycling stability by revealing capacitance retention of 82% after 200 cycles. It can conclude that biomass-based rGO paper sheet can be a potential candidate as environmentally safe with remarkable electrochemical activity in energy storage applications.

Although Al-ion battery is attracting researchers’ attention worldwide, its volumetric energy density was not so promising due to low density of graphite-based positive electrodes in the current published literatures. Thus, defect-free yet densely packed graphene electrodes with high electronic conductivity and fast ionic diffusion are crucial to the realization of compacted Al-ion batteries with high volumetric energy density. In the present work, a self-supported and defect-free graphene-positive electrode (RHG-P-2850) was successfully produced by a hydriodic acid reduction of the graphene oxide (GO) method, followed by an ultrahigh temperature (2850 °C) annealing treatment. The density of the RHG-P-2850 (0.32 g cm−3) is currently the highest positive electrode material in the preparation of graphene-positive electrodes from GO. RHG-P-2850 positive electrode enables to deliver considerably high specific capacity 27.1 mAh cm−3 (85 mAh g−1) at the current density 2 A g−1. More importantly, a remarkably stable performance was achieved with 20% fading over 8000 cycles. The results enlighten and promote the design and preparation of densely packed graphene-positive electrode to develop high-performance Al/graphene battery.

Nowadays, the needs of bendable energy storage components are growing to match with the development of wearable devices. However, it is still a great challenge to fabricate flexible electrodes to k...

The use of membranes in integrated water systems has garnered increasing attention in paper mills operating with virgin fibres, with documented closed water loops in industry. However, limited research exists on the performance of ultrafiltration (UF) in mills operating with 100% recycled fibres (RCF) and closed water systems, as these result in the introduction and accumulation of insoluble contaminants in the effluent. This study investigated the effect of transmembrane pressure (TMP) and feed organic load on the flux, types of fouling, and organic separation with UF membranes in a recycled paper mill using 100% RCF. The high feed organic load caused inevitable fouling, limiting the highest achievable flux. However, the TMP could be manipulated to improve on or exacerbate the process performance, within the range that was set as a result of the feed's characteristics. Low TMP (1.35 bar) generated the highest permeability and chemical oxygen demand removal, while higher TMPs produced higher fluxes and recoveries. The process was characterised by high initial fluxes, followed by cake formation, which dominated, and pore blockage. The excess cake formation induced cake filtration. This study shows the potential of UF membranes to be used as pre-treatment in filtering the process water in a recycled paper mill operating with 100% RCF, a critical step forward in implementing an integrated water system, and eventually closing the water loop.

Civil Construction Industry impacts significantly the environment, being one of the most critic factors related to elevated production of Civil Construction Residue (CCR). Among CCR produced, the Kraft paper package acquires notoriety, due their large use on material packaging, such as Portland cement and lime, then, present a high production rate and offer contamination potential, lack of collection logistics and nearly any reuse. In this scenario, the study and development of alternative constructive materials which applies the sustainability concept and CCR recycling have acquired great relevance in the sector. It is highlighted the residue incorporation on masonry soil-cement blocks, due its block are not submitted to the sintering process. Then, the present research intend to study adobe blocks mechanical properties based on soil-cement reinforced with cellulose fibers obtained from Kraft paper recycling. The bricks were confectioned with 7% Portland cement content and with 0%, 8%, 10% e 12% Kraft paper fiber addition, being submitted to compressive strength test, water absorption test, durability test with wetting and drying and retraction analysis. It was verified the confectioned composites presented as a viable and interesting alternative on technical and environment range. All studied researches presented null retraction and compressive strength increase on cracked state, toughness increase and good performance about durability.

L -dopa is a chiral drug that has been extensively used for the treatment of Parkinson’s disease. The concentration of L -dopa plays a vital role in the treatment, and this work emphasizes on designing a versatile platform for the quantitative and selective detection of L -dopa using reduced graphene quantum dot (rGQD). The platform is efficient in three different sensing methods, viz. fluorescence turn-on, filter paper-based sensing, and electronic measurements. The rGQD undergoes a dramatic fluorescence turn-on in the presence of L -dopa in aqueous media and artificial urine with a detection limit as low as 1.307 µM and 1.217 µM respectively. Experimental evidence revealed that the fluorescence enhancement is attributed to aggregation-induced emission mechanism. The system is also applicable for visual detection of L -dopa using filter paper strips treated with rGQD and develops bright fluorescence under ultra-violet irradiation. Apart from this, electrical sensors for L -dopa were also developed by preparing rGQD treated poly-vinyl alcohol films, and the increase in the current conduction with varying concentrations of L -dopa was observed. The films produce 2.5 order higher current conduction at 300 μM of L -dopa with a detection limit of about 13.136 µM. At the final stage, we have designed flexible electronic devices using these materials that develop 1.3 order higher current for L -dopa. The devices exhibit excellent air stability under varied relative humidity conditions as well as high bending stability for potential practical applications.

Traction transformers are one of the most important equipment in the traction power supply system. Thermal aging of transformer insulation system determines its reliable life. To achieve an estimation of the insulation life of traction power transformers operated under real load condition, the effects of traction loads on the thermal aging of oil-paper insulation in traction transformers were investigated. First, the design principles for the accelerated thermal aging experiment were studied and proposed by considering magnitude (i.e., load rate) and frequency (i.e. spare time and lasting time) of the traction load. Then, an experimental system was established in the laboratory to conduct extensive accelerated thermal aging experiments, in which the traction loads were mimicked by using positive temperature coefficient (PTC) heating plates and a programmable logic controller (PLC). Finally, the experimental results were analyzed and discussed to reveal the effects of traction load on the thermal aging of oil-paper insulation in traction transformers.

This paper utilizes a hybrid Debye model to accurately simulate the relaxation response process of the oil‐paper insulation of a transformer to explore the application of frequency domain dielectric spectroscopy (FDS) in nondestructive diagnosis of the aging condition of oil‐paper insulation. Via FDS test data, the model parameters can be identified, and the influence laws of FDS can be obtained through the variation of model parameters. To explore the effects of insulating paper moisture content, insulating paper layers, and test temperature on FDS characteristics, an FDS experimental platform is established. The results show that the hybrid Debye model can effectively reflect the relaxation response process of oil‐paper insulation under different conditions, as well as that a physical relationship between the model parameters and oil‐paper dielectric polarization exists. In addition, the parameters of the hybrid Debye model can be used as the characteristic quantities for the non‐destructive evaluation of the oil‐paper insulation state, providing new ideas for the non‐destructive evaluation of the oil‐paper insulation state.

Background We use inkjet printing and film adhesion methods to economically develop paper-based electrowetting-on-dielectric (EWOD) mixing device. Because the periodic shrinking and stretching of droplet contact line induces surface capillary wave, the coalesced droplet on EWOD device vibrates to accelerate solute mixing on the merged spot. Methods An office inkjet printer fabricates pads of conducting silver nanoparticles to compose EWOD activation electrodes on a piece of glossy label paper, covered with one oil-coated dielectric film. Using the triggering relays of each pad, two droplets of thirty microliter individually loaded on the electrode ends are driven to coalesce. Alloy nanorod-catalyzed chemiluminescence assay can be performed on this mixing device. Findings When ac voltage of 100 Hz is applied on the electrode flakes, compared with solute transport efficiency in static condition, solute diffusivity is enhanced by 4 times using this mixing device. Linear relation (R2 = 0.99) between luminescence intensity acquired with smartphone camera and luminol concentration of aforementioned chemiluminescence assay is obtained, demonstrating reproducibility improvement for accurate determination.

We propose a paper solar cell based on carbon nanotube (CNT)-composite papers. To fabricate this cell, we use dye-sensitized solar cells (DSCs) for generating power through the redox reaction of dyes in conjunction with CNT-composite papers, which are composite materials containing CNTs and pulp (raw paper material) that can be fabricated easily by using a method based on the Japanese washi papermaking technique. The demand for CNT applications is expected to increase due to their high conductivity and metallic or semiconducting characteristics. This CNT-composite paper can also have metallic or semiconducting characteristics based on the contained CNTs in the composite paper. We previously fabricated a DSC that generates electricity by using CNT-composite papers stacked in a typical DSC structure. However, the conversion efficiency of this DSC was just 0.188%, which is not practical. To overcome this low power generation issue, we tried improving the DSC structure by applying electrodes to the CNT-composite papers in grid patterns for efficient current collection and applying an optimally mixed dye for efficient electron excitation. Results showed that the conversion efficiency improved to 0.58%. Moreover, we demonstrated that using a mixed dye can improve the conversion efficiency of the paper DSC. We expect these types of CNT-composite papers to be used as material for new DSCs.

Electronic paper is now closer than ever to changing the way we read, write, and study. This was hailed as a revolution so profound that some see it as second only to the invention of the printing press in the 15th century. In this study, four analytical methods, which included statistical analysis, technology decomposition, multistage technological evolution and growth potential analysis were used. Results showed that technological research on business has great potential for development and vast market, and it would be another 16 years before the limit could be reached for patents. A great deal of technology breakthrough has been achieved during 1992 and 2012. The four major countries for printed electronic paper development are Japan, USA, South Korea and China. However, China has a gap compared with other countries, as the key technology was held by large enterprises. The apparatus for printed electronic paper has been the major focus in China. The key point for research on printed electronic paper was focused on devices for presentation and light emission, and related semiconductor devices.

The construction of a photoelectrochemical (PEC) strategy for multi-component detection represents a great challenge in the field of sensing. To address these challenges, herein we presented a hollow-channel paper-based PEC analytical platform based on chemiluminescence (CL) addressable strategies excited PEC strategy for multiplexed sensing application. Sandwich-structured CdS quantum dots (QDs)/reduced graphene oxide (RGO)/ZnO nanorods arrays (NRAs) heterostructure where CdS serves as visible light sensitizers, RGO acts as an electron relay between ZnO NRAs and CdS QDs, were simply assembled on the gold nanoparticles modified paper working photoelectrode (Au-PWE). The PEC performance of the CdS/RGO/ZnO can be greatly improved benefiting from the formation of type II band alignment between CdS QDs and ZnO NR as well as the super charge collection and shuttling property of RGO. Multiplexed CL emission could be achieved through controlling the CL co-reagents transport. By the virtue of CL addressable technique and the excellent PEC activity of CdS/RGO/ZnO, a highly sensitive, and selective multiple microRNAs (miRNAs) quantification method was achieved. Such a tailored strategy would break the bottleneck of the current PEC detection techniques in multiplex tracing, as well as serve as a novel concept for designing multi-channel PEC sensing method.

A simple, scalable approach is developed to fabricate a flexible hybrid paper electrode composed of the polyaniline/graphene and the carbon fiber (CF)-reinforced bacterial cellulose. The prepared hybrid paper presents high areal capacitance of 4.145 F cm−2 at 5 mA cm−2 and an extremely low sheet resistance of 29.7 Ω sq.−1. The CF endows the paper electrode remarkable foldability with no mechanical destruction. Even after being repeatedly bent 180° up to 1000 times, the initial capacitance can be retained up to 98%. A fabricated all-solid-state supercapacitor based on the resulting paper electrode has an excellent areal capacitance of 630 mF cm−2 and energy density of 2.8 mWh cm−3. The results confirm that this approach can fabricate the highly foldable and shape-tailorable energy storage devices and may have wide potential applications.

Flexible and lightweight shielding materials recently have attracted increasing attention for terahertz wave due to the deteriorated performance of electronic equipment interferenced by electromagnetic yielding. Herein, flexible reduced graphene oxide (rGO) papers were prepared by solution evaporation method to attenuate the electromagnetic wave in terahertz field. They exhibited excellent electrical conductivity and remarkable electromagnetic interference shielding effectiveness. The electrical conductivity of the rGO papers was improved from 54.07 to 78.67 S/cm after annealing at 400 °C. The rGO paper annealed at 400 °C was only ~ 370 µm in thickness and particularly exhibited an outstanding absorption performance of 17.6 dB at 0.7 THz. It has been found that the maximum absorption performance of rGO papers was basically equivalent to that of the metamaterials. Moreover, electromagnetic interference shielding effectiveness of 72.1 dB of the rGO papers was obtained at 0.6 THz, which indicated that ~ 99.99% of the power was shielded. Thus, the flexible rGO papers maybe a promising candidate for optimized electromagnetic shielding materials in the terahertz band.

The progress in the fabrication of carbon-nanotube-based structures has made it possible to use Raman spectroscopy to measure the deformation states of carbon nanotubes and abutting materials. In this work, we investigate the effects of laser power and surrounding materials on the Raman shift of carbon-nanotube (CNT) papers for the laser intensity in a range of 0.071 to 1.415 kW/mm2 without action of mechanical loading. Two different configurations of the CNT papers are used in the Raman measurement; one uses a suspended CNT paper, and the other places a CNT paper on a glass or aluminum substrate. The experimental results reveal that there exist combinational effects of the laser power and abutting materials on the changes of the wavenumbers of the D, G and G′ bands of the CNT papers. We derive an analytical relation between the strain components, temperature and the change of the wavenumber of the Raman peak, which yields a proportional relationship between the change of the wavenumber of the Raman peak and the laser power. Such a relationship is supported by the experimental results.

This article presents the use of flexible carbon substrates for the growth of III-nitride nanowire light emitters. A dense packing of gallium nitride nanowires were grown on a carbon paper substrate. The nanowires grew predominantly along the a-plane direction, normal to the local surface of the carbon paper. Strong photo- and electro-luminescence was observed from InGaN quantum well light emitting diode nanowires.

Halide perovskite quantum dots (PQDs) are promising materials for diverse applications including displays, light‐emitting diodes, and solar cells due to their intriguing properties such as tunable bandgap, high photoluminescence quantum yield, high absorbance, and narrow emission peaks. Despite the prosperous achievements over the past several years, PQDs face severe challenges in terms of stability under different circumstances. Currently, researchers have overcome part of the stability problem, making PQDs sustainable in water, oxygen, and polar solvents for long‐term use. However, halide PQDs are easily degraded under continuous irradiation, which significantly limits their potential for conventional applications. In this study, an oleic acid/oleylamine (traditional surface ligands)‐free method to fabricate perovskite quantum dot papers (PQDP) is developed by adding cellulose nanocrystals as long‐chain binding ligands that stabilize the PQD structure. As a result, the relative photoluminescence intensity of PQDP remains over ≈90% under continuous ultraviolet (UV, 16 W) irradiation for 2 months, showing negligible photodegradation. This proposed method paves the way for the fabrication of ultrastable PQDs and the future development of related applications., Solid‐state perovskite quantum dot papers are fabricated using a unique vacuum filtration growth method without a purification process. The bonding between cellulose nanocrystals and perovskite quantum dots makes the hybrid structure stable, and record high UV stability and thermal stability are achieved for perovskite quantum dot papers.

Triboelectric nanogenerators (TENGs) have been introduced as a rational and effective way of powering the low consuming electronic devices and sensors. Mostly these nanogenerators are manufactured using costly materials and complex fabrication processes that restrict their usage especially in developing countries. In this paper, we have presented an inexpensive and facile TENG for powering the environmental sensor. Readily available and cost-effective materials were used for manufacturing TENG like paper, thread sealant PTFE tape, and pencil. The manufactured paper based TENG produced short circuit current and open circuit voltage of $110\ \mu \mathrm{A}$ and 234 V respectively. The maximum power density of $96.22\ \mu \mathrm{W} /$ cm2 was achieved at 5 M $\Omega$. The rectified signal from TENG was used to charge a capacitor array of $300\ \mu \mathrm{F}$ which was successively used to power the environmental sensor. Temperature and humidity can be measured by powering the environmental sensor with the help of the proposed TENG. This facile and cost-effective TENG can be easily manufactured and deployed in resource limited environment for self-powered sensing systems.

The graphene paper microsieves can be applied in the filtration of biological fluids or separation of solid particles from exploitation fluids. To produce graphene paper microsieves for specific applications, good control over fabrication should be achieved. In this study, a laser ablation method using a picosecond laser was applied to fabricate graphene paper microsieves. Holes in the microsieves were drilled using pulsed laser radiation with a pulse energy from 5 to 100 &micro, J, a duration of 60 ps, a wavelength of 355 nm, and a repetition rate of 1 kHz. The impact method was applied using 10 to 100 pulses to drill one hole. To produce holes of a proper diameter which could separate biological particles of a certain size (&ge, 10 &micro, m), optimum parameters of graphene paper laser ablation were defined using the MATLAB software taking into account laser pulse energy, repetition rate, and a desired hole diameter. A series of structural tests were carried out to determine the quality of an edge and a hole shape. Experimental results and Laguerre&ndash, Gauss calculations in MATLAB were then compared to perform the analysis of the distribution of diffraction fringes. Optimum experimental parameters were determined for which good susceptibility of the graphene paper to laser processing was observed.

Made available in DSpace on 2022-04-29T08:36:18Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-12-01 Paper electronics has emerged as an ecofriendly, light, low-cost, and recyclable material for the fabrication of flexible and printed transistors. In this study, we present fully printed organic electrochemical transistors using an active layer of PEDOT:PSS, carbon electrodes, cellulose-based electrolyte, and three different papers as substrates: bond, vegetal, and Lumi Silk, relating the electrical properties to the different morphologies of the paper surfaces. Each paper presents different regularity, diffusion capabilities, and roughness, with significant influence on the transistor performance. The more organized and smooth the surface, the better the electrical characteristics, the best of these being the Lumi Silk, with higher I on/I off ratio of 46, on-current of 8.3 10-5 A, V on of 1.3 V, and power gain of 43.5 dB associated with ultra-low hysteresis of 0.1 V, high transconductance of -57.3 μS, and suitablity for flexible electronics and sensors applications. S o Paulo State University - UNESP Faculty of Science and Technology (FCT) Physics Department, SP Universidade NOVA de Lisboa and CEMOP-UNINOVA Faculty of Science and Technology (FCT) CENIMAT/I3N Department of Materials Science S o Paulo State University - UNESP Faculty of Science and Technology (FCT) Physics Department, SP

Light-reflecting characteristics play a crucial role in optically rewritable liquid crystal display (electronic paper). By using a special optimizer software, light-reflecting characteristics of the twisted nematic cell were calculated. The achieved values of the normalized reflection coefficients range within ∼ 0.03 - 0.43, which is comparable or better than other commercial technologies. The calculated contrast ratio of the device is 10 : 1. A 2D image, which can be displayed on the electronic paper was obtained. Comparison of the simulated background color and contrast ratio is very similar with the results, which were obtained in experimental cells of other studies. Our calculations indicate that angular dependence of the reflectance coefficient is almost uniform within a wide range of viewing angles.

Graphene-based papers have recently triggered considerable interests in developing the application as thermal interface materials (TIMs) for addressing the interfacial heat transfer issue, but their low through-plane thermal conductivity (κ⊥), resulting from the layer-by-layer stacked architecture, limits the direct use as TIMs. Although various hybrid graphene papers prepared by combining the graphene sheets and the thermally conductive insertions have been proposed to solve this problem, achieving a satisfactory κ⊥ higher than that of commercial TIMs (>5 W m−1 K−1) remains challenging. Here, a strategy aimed at the construction of heat pathways along the through-plane direction inside the graphene paper for achieving a high κ⊥ was demonstrated through the simultaneous filtration of graphene sheets with two different lateral sizes. The as-prepared graphene paper presented a hierarchical structure composed of loosely stacked horizontal layers formed by large graphene sheets, intercalated by a random arrangement of small graphene sheets. Due to the heat pathways formed by small graphene sheets along the through-plane direction, the hierarchically structured graphene paper exhibited an improved κ⊥ as high as 12.6 W m−1 K−1 after a common graphitization post-treatment. In the practical test, our proposed paper as an all-graphene TIM achieved an enhancement in cooling efficiency of ≈ 2.2 times compared to that of the state-of-the-art TIM, demonstrating its superior performance to meet the ever-increasing heat dissipation requirement.

Thermal switches control thermal circuits and are widely used in electronics and engineering. Shape-memory alloys can be deformed by heating, which is widely used as a driving part for ther...

Here, we reported an ingenious fabrication of moisture responsive graphene-based actuator via unilateral two-beam laser interference (TBLI) treatment of graphene oxide (GO) papers. TBLI technique has been recognized as a representative photoreduction and patterning strategy for hierarchical structuring of GO. The GO paper can be reduced and cut into grating-like periodic reduced graphene oxide (RGO) microstructures due to laser ablation effect. However, the lower light transmittance of the thick GO paper and the corresponding thermal relaxation phenomenon make it impossible to trigger complete reduction, leading to the formation of the anisotropic GO/ reduced GO (RGO) bilayer structure. Interestingly, the RGO side that feature lower OCGs and higher roughness shows strong water adsorption due to the formation of micronanostructures. Due to the different water adsorption capacities of the two sides, a flower moisture-responsive actuator has been fabricated, which exhibits “opening” and “closing” behavior under different humidity conditions.

Paper electronics have been fast developed in recent years due to their degradability and recyclability; however, most of them are barely equipped with logic functions, impeding them from becoming autonomous on-paper systems. To provide a working unit for logic implementations, a paper field-effect transistor (FET) with a clay-graphite channel that demonstrated negative differential resistance (NDR) is fabricated in this study. The device exhibited a p-type semiconductor characteristic with an optical bandgap of ∼1.97 eV according to photoluminescence analysis, resulting from considerable defective graphite mixed with clay in the channel. Considering that the NDR behavior is theoretically predicted to be tunable by the contact resistance, we fabricated FETs with different contact resistances and observed that the NDR behavior occurred in devices with relatively lower contact resistance. The NDR effect is also tunable by varying the gate voltage, which matches well with simulation results. The possible mechanism for the NDR behavior is the decrease in carrier drift velocity induced by band-to-band tunneling, associated with impurities-induced trapping states and gate-induced confined states. This work provides a promising and easy pathway to develop digital components using paper electronics in the near future.

To improve the accuracy of color reproduction for camouflage printing, a new color matching method, named monitor-paper-fabric, was proposed by importing color management into textiles, which matched the printing pastes according to the color of the paper card printed by the ink-jet printer after color management. Not like the traditional color matching method, it matched the printing pastes according to the color from computer monitor after color correction. Two color matching methods were analyzed by comparing the color difference. It was found that the “monitor-paper-fabric” color matching method could be considered as a convenient and feasible color matching method. Most color differences between the monitor and the fabric in the camouflage pattern were reduced to lower than 4, except for color blocks 5 and 6. In addition, the color differences of six color blocks between the paper and the fabric were all less than 3.5, and were lower than those between the monitor and the fabric. The color consistency between the paper and the fabric was better than that between the monitor and the fabric.

The photon energy of terahertz waves is of the order of a few milli-electronvolts and is much lower than the thermal energy of ~ 26 meV at room temperature. However, the fast and sensitive detection of terahertz waves is notoriously difficult at ambient conditions. Moreover, the material flexibility is also very important within existing terahertz technologies for development of wearable and portable terahertz devices. We experimentally demonstrate that multiwall carbon nanotube flexible paper (MWCNT-FP) is one of the potential candidates to be used for terahertz detectors at room temperature. For the first time, MWCNT-FP sample is measured over a wide frequency band ranging from 0.02 to 4.5 THz at room temperature as compared to previously reported materials that demonstrate prominent frequency response between 0.2 and 2.5 THz. The MWCNT-FP sample delivered wide band absorption between 0.02 and 4.0 THz. Over the transmission, a high absorption peak is detected at 1.0 THz. The optical density spectrum is observed around 1.25 and 3.37 THz in the low-frequency regime and high-frequency regime, respectively. The present results suggest the potential application of MWCNT-FP as a wearable THz detector.

Traction transformers have been withstood the effects of shock load, which would become more than 2~3 times rated load when the train passes, and it can result in the winding insulation under short-term high temperature frequently. And the average load far less than 50% result in relatively low oil temperature, the very uneven rise of temperature lead to the very uneven distribution of insulation aging. In order to evaluate the aging life of oil-paper insulation of traction transformer under shock load effectively, in this paper, Ekenstam aging kinetic model was optimized considering the effect of shock temperature, shock duration and shock interval on cellulose degradation rate of insulating paper. Firstly, the effects of shock temperature, shock duration and shock interval on the parameters of Ekenstam model are analyzed and determined by handing and testing experimental materials. Then, according to the test data, the Ekenstam optimization model considering shock temperature, shock duration and shock interval is obtained. Finally, the optimized model is verified by experiments. The results show that the optimization model can effectively evaluate the aging life of oil-paper insulation of traction transformer under shock load in the temperature range, which provides a basis and reference for the subsequent related research.

We report a laser-based photo-polymerisation technique for the fabrication of 3D -multilayer paper-based devices. This method circumvents fabrication issues associated with other reported methods (e.g. alignment, contact), providing a pathway for mass-manufacture of paper-based devices.

This paper presents the integration process of an ultra-thin PZT/Si chip on paper and that it functions as a simple speaker by applying a voltage in the audible frequency range. The PZT/Si chip used is only 5-μm-thick, so it does not interfere with the flexibility of the substrate, and it can be integrated on paper because it does not use a high-temperature process in the electrode connection process. We have revealed that a paper with an ultra-thin PZT/Si chip of only 1 × 5 mm2 in size generates a fully audible sound pressure level (SPL) of about 40 dB. It was rounded to a radius of curvature of 1 cm without breaking. The overall SPL was about the same even when the paper substrate dimension was reduced to 50 mm square. This technology is expected to be applied to electronic components such as surround speakers or haptics in electronic paper.