Search

In this work is exploited the possibility to use two optical techniques and combining their measurements for the 3D characterization of different tyres with particular attention to the tyre's section. Electronic Speckle Pattern Interferometry (ESPI) and Laser Scanner (LS) based on principle of triangulation have been employed for investigating and studying the tyre's section and 3D shape respectively. As case studies two different racing tyres, Michelin S9H and Pirelli Diablo respectively, have been considered. The investigation has been focused at the aim to evaluate and measure the section's components in order to add to the 3D model obtained by Laser Scanning accurate information about the different layers along through the tyres sections. It is important to note that the assessment about the different layers along the section is a very difficult task to obtain by visual inspection or classical microscopy and even with the LS. Here we demonstrate that the different layers can be easily highlighted and identified by mean of the ESPI.

The study of the human body and its movements is still a matter of great interest today. Most of these issues have as their fulcrum the study of the balance characteristics of the human body and the determination of its Centre of Mass. In sports, a lot of attention is paid to improving and analysing the athlete’s performance. Almost all the techniques for determining the Centre of Mass make use of special sensors, which allow determining the physical magnitudes related to the different movements made by athletes. In this paper, a markerless method for determining the Centre of Mass of a subject has been studied, comparing it with a direct widely validated equipment such as the Wii Balance Board, which allows determining the coordinates of the Centre of Pressure. The Motion Capture technique was applied with the OpenPose software, a Computer Vision method boosted with the use of Convolution Neural Networks. Ten quasi-static analyses have been carried out. The results have shown an error of the Centre of Mass position, compared to that obtained from the Wii Balance Board, which has been considered acceptable given the complexity of the analysis. Furthermore, this method, despite the traditional methods based on the use of balances, can be used also for prediction of the vertical position of the Centre of Mass.

The characterization and reproduction of tyre behaviour for vehicle modelling is a topic of particular interest both for real-time driver in the loop simulations and for offline performance optimization algorithms. Since the accuracy of the tyre forces and moments can be achieved by the accurate physical modelling of all the phenomena concerning the tyre-road interaction, the link between the tyre thermal state and the tyre frictional performance turns into a crucial factor. An integrated numerical methodology, allowing to couple the full 3D CFD (Computational Fluid Dynamics) flux within the internal chamber of the tyre with an equivalent discrete 3D structure model, is proposed with the aim to completely represent the tyre thermodynamic convective behaviour in the steady-state operating conditions. 3D CFD model enables the evaluation of the internal distribution of the gas temperature and of the thermal powers exchanged at each sub-wall in detail. This allows to increase the reliability of the tyre thermodynamic modelling with a particular reference to the proper managing of the aero-thermal flow of the brake disc impact on the rim temperature and therefore on the internal gas dynamics in terms of temperature and pressure, being able to optimize the tyre overall dynamic performance in both warm-up and stabilized thermal conditions. The steady RANS (Reynolds Averaged Navier–Stokes) simulations have been performed employing the 3D CFD model in a wide range of angular velocities with the aim to calculate the convective thermal flux distributions upon rim and inner liner surfaces. The simulation results have been then exploited to derive the convective heat transfer coefficients per each sub domain to be employed within the real-time tyre physical thermal model, with the peculiar advantage of an enhanced model reliability for thermal characteristics. To validate the proposed methodology, the tyre thermal model outputs, in terms of temperatures of internal and external layers, have been validated towards the acquired ones within the specific routine performed on tyre force and moment test bench, confirming an excellent agreement with the experimental data in the entire range of operating conditions explored.

Tyres play a key role in ground vehicles' dynamics because they are responsible for traction, braking and cornering. A proper tyre-road interaction model is essential for a useful and reliable vehicle dynamics model. In the last two decades Pacejka's Magic Formula (MF) has become a standard in simulation field. This paper presents a Tool, called TRIP-ID (Tyre Road Interaction Parameters IDentification), developed to characterize and to identify with a high grade of accuracy and reliability MF micro-parameters from experimental data deriving from telemetry or from test rig. The tool guides interactively the user through the identification process on the basis of strong diagnostic considerations about the experimental data made evident by the tool itself. A motorsport application of the tool is shown as a case study.

The tire and vehicle setup definition, able to optimise grip performance and thermal working conditions, can make the real difference as for motorsport racing teams, used to deal with relevant wear and degradation phenomena, as for tire makers, requesting for design solutions aimed to obtain enduring and stable tread characteristics, as finally for the development of safety systems, conceived in order to maximise road friction, both for worn and unworn tires. The activity discussed in the paper deals with the analysis of the effects that tire wear induces in vehicle performance, in particular as concerns the consequences that tread removal has on thermal and frictional tire behaviour. The physical modelling of complex tire–road interaction phenomena and the employment of specific simulation tools developed by the Vehicle Dynamics UniNa research group allow to predict the tire temperature local distribution by means of TRT model and the adhesive and hysteretic components of friction, thanks to GrETA model. The cooperation between the cited instruments enables the user to study the modifications that a reduced tread thickness, and consequently a decreased SEL (Strain Energy Loss) and dissipative tread volume, cause on the overall vehicle dynamic performance.

Accurate estimation of the vehicle sideslip angle is fundamental in vehicle dynamics control and stability. In this paper two different methods for vehicle sideslip estimation, based on Principal Component Analysis (PCA) and Neural Networks (NN), are presented comparing the procedure responses with full-scale vehicle acquired test data. The estimation algorithms use driver's steering angle, lateral and longitudinal accelerations, wheel angular velocities and yaw rate measured from sensors integrated in a test vehicle, and are validated by comparison with the measurements of the sideslip angle provided by an optical Correvit sensor suitably mounted on board, serving as the reference system in terms of accuracy of slip-free measurement of longitudinal and transverse vehicle dynamics. The procedure results, based on both the original (RAW) and the reduced (PCA) data sets, are compared to the acquired sideslip angle, using the estimated channel as an input for the TRICK tool to evaluate the accuracy of the results and the potential of the estimation process in terms of tire interaction curves.

This paper deals with in-curve vehicle lateral behaviour and is aimed to find out which vehicle physical characteristics affect significantly its stability. Two different analytical methods, one numerical (phase plane) and the other graphical (handling diagram) are discussed. The numerical model refers to the complete quadricycle, while the graphical one refers to a bicycle model. Both models take into account lateral load transfers and nonlinear Pacejka tyre–road interactions. The influence of centre of mass longitudinal position, tyre cornering stiffness and front/rear roll stiffness ratio on vehicle stability are analysed. The presented results are in good agreement with theoretical expectations about the above parameters influence, and show how some physical characteristics behave as saddle-node bifurcation parameters.

The most powerful engine, the most sophisticated aerodynamic devices or the most complex control systems will not improve vehicle performances if the forces exchanged with the road are not optimized by proper employment and knowledge of tires. The vehicle interface with the ground is constituted by the sum of small surfaces, wide about as one of our palms, in which tire/road interaction forces are exchanged. From this it is clear to see how the optimization of tire behavior represents a key-factor in the definition of the best setup of the whole vehicle. Nowadays, people and companies playing a role in automotive sector are looking for the optimal solution to model and understand tire׳s behavior both in experimental and simulation environments. The studies carried out and the tool developed herein demonstrate a new approach in tire characterization and in vehicle simulation procedures. This enables the reproduction of the dynamic response of a tire through the use of specific track sessions, carried out with the aim to employ the vehicle as a moving lab. The final product, named TRICK tool (Tire/Road Interaction Characterization and Knowledge), comprises of a vehicle model which processes experimental signals acquired from vehicle CAN bus and from sideslip angle estimation additional instrumentation. The output of the tool is several extra "virtual telemetry" channels, based on the time history of the acquired signals and containing force and slip estimations, useful to provide tire interaction characteristics. TRICK results can be integrated with the physical models developed by the Vehicle Dynamics UniNa research group, providing a multitude of working solutions and constituting an ideal instrument for the prediction and the simulation of the real tire dynamics.

This paper deals with the frictional behaviour of a tyre tread elementary volume in sliding contact with road asperities. Friction is assumed to be composed of two main components: adhesion and deforming hysteresis. The target, which was fixed in collaboration with a motorsport racing team and with a tyre-manufacturing company, is to provide an estimation of local grip for online analyses and real-time simulations and to evaluate and predict adhesive and hysteretic frictional contributions arising at the interface between the tyre tread and the road. A way to approximate the asperities, based on rugosimetric analyses on a macroscale and a microscale, was introduced. The adhesive component of friction was estimated by means of a new approach based on two different models found in the literature, whose parameters were identified thanks to a wide experimental investigation previously carried out. The hysteretic component of friction was estimated by means of an energy balance taking into account the viscoelastic behaviour of rubber (which was characterized by means of appropriate dynamic mechanical analysis tests) and the internal stress–strain distribution (which was due to indentations of the road). The model results are finally shown and discussed, and the validation experimental procedure is described. The correct reproduction of the friction phenomenology and the model prediction capabilities are highlighted, making particular reference to the grip variability due to changes in the working conditions.