Search

Human detection and classification via Wi-Fi transmission have received a lot of attention in recent years as crucial facilitators in security and humancomputer interaction (HCI). The passive Wi-Fi radar (PWR) system used by previous researchers applied cross-ambiguity function (CAF) and CLEAN algorithms to process the detected signals. This paper explores the feasibility and viability of a PWR system in detecting and classifying human movements without utilizing CAF and CLEAN algorithms. The movements are performed by four participants but with comparable body sizes and heights. Three daily human movements are investigated namely walking, bending, and sitting, with each participant performing each movement 24 times, providing a total of 96 samples per activity. The system is evaluated based on the consistency of the signal pattern in a frequency domain and the percentage accuracy is assessed using an artificial neural network (ANN) classifier and trained using a leave-one-out cross-validation (LOOCV) method. The frequency domain results reveal that the signals are consistent, with no noticeable variations or changes in the voltage intensity or shape of the main lobe. The classification of the movements shows that the classifier has an overall accuracy of 97.6%. [ABSTRACT FROM AUTHOR]

Passive radar detection emerges as a pivotal method for environmental perception and target detection within radar applications. Through leveraging its advantages, including minimal electromagnetic pollution and efficient spectrum utilization, passive radar methodologies have garnered increasing interest. In recent years, there has been an increasing selection of passive radar signal sources, and the emerging 5G has the characteristics of a high-frequency band, high bandwidth, and a large number of base stations, which give it significant advantages for use in passive radar. Therefore, in this paper, we introduce a passive radar target detection method based on 5G signals and design a rotating target speed measurement experiment. In the experiment, this paper validated the method of detecting rotating targets using 5G signals and evaluated the measurement accuracy, providing a research foundation for passive radar target detection using 5G signals and detecting rotating targets such as drone rotors. [ABSTRACT FROM AUTHOR]

The application and uses of drones in all areas are continuously rising, especially in civilian use cases. This increasing threat requires reliable drone surveillance in urban environments. Radar is the obvious candidate with its ability to detect small objects at range, in all weather conditions. The use of an L‐band networked radar for urban sensing of S‐UAS targets is explored. Small echoes from S‐UAS places a premium on synchronisation, which is the fundamental key for high performance networked radar. The effect of timing errors on the operation of the network radar is investigated theoretically and experimentally, and the processing tools for synchronising data based on the direct signal returns of the transmitter are developed. Also, drone detection using bistatic L‐band staring radar is achieved both in simulation and then in real field trials where the SNR and detection performance are computed and analysed. The updated direct signal synchronisation method for bistatic staring radar is shown to provide comparable SNR and positional accuracy for S‐UAS targets as the monostatic staring radar. [ABSTRACT FROM AUTHOR]

The use of WiFi signals for sensing purposes has attracted a lot of interest from both the radar and communications communities and several techniques have been explored. In the attempt of meeting the requirements for small sensor size, compactness, and easy deployment, the authors consider reference‐free approaches, namely approaches that do not require a good copy of the transmitted waveform to be available at the radar receiver. To this end, the authors first resort to a passive radar‐based processing scheme that only exploits the invariant a priori known initial portion of the physical layer protocol data unit, that is, the PHY Preamble, and its limitations in practical applications is investigated. Specifically, the authors show that, with this approach, an accurate time, phase, and frequency synchronization is essential and a possible strategy is investigated. As an alternative solution the authors consider a forward scatter radar‐based approach where only the amplitude modulation of the received signal is exploited to detect the presence of a moving target thus avoiding the need to know the transmitted signal. For the first time, the authors comparatively investigate advantages and drawbacks of the two reference‐free approaches and present practical strategies to handle the limitations observed. The results are reported for experimental tests with people and drones using WiFi transmissions in the 2.4 and 5 GHz band. [ABSTRACT FROM AUTHOR]

This paper proposes a simple non‐adaptive approach for the suppression of direct signal and clutter contributions in a passive radar system based on orthogonal frequency division multiplexing transmissions, exploiting the properties of a reciprocal filter (RF). The use of a RF allows to circumvent the limits posed by the waveform ambiguity function, producing a data‐independent time‐invariant response to a stationary point‐like target echo at the output of the range compression stage. This feature enables simple clutter cancellation strategies, based on the subtraction of delayed portions of the surveillance signal, according to the conventional moving target indication methodologies. The proposed processing scheme consists of a range compression stage based on a RF, followed by a Single Canceller. Its performance is investigated against a simulated and an experimental data set, for the case of a digital video broadcasting‐terrestial‐based passive radar scenario, and it is compared to an alternative scheme based on a conventional matched filter and adaptive cancellation techniques. The proposed approach is shown to yield a perfect cancellation of the clutter returns from a stationary scene under ideal conditions. Moreover, it proves to be robust to real‐world conditions, despite its considerably limited computational load compared to adaptive clutter cancellation techniques. [ABSTRACT FROM AUTHOR]

Passive bistatic radar is a novel radar technology that passively detects targets without actively emitting signals. Since passive bistatic radar entails larger data volumes and computations compared to traditional active radiation radar, the development of hardware and software platforms capable of efficiently processing signals from passive bistatic radar has emerged as a research focus in this field. This research investigates the signal processing flow of passive bistatic radar based on its characteristics and devises a parallel signal processing scheme under graphic processing unit (GPU) architecture for computation-intensive tasks. The proposed scheme utilizes high-computing-power GPU as the hardware platform and compute unified device architecture (CUDA) as the software platform and optimizes the extensive cancellation algorithm batches (ECA-B), range Doppler and constant false alarm detection algorithms. The detection and tracking of a single target are realized on the passive bistatic radar dataset of natural scenarios, and experiments show that the design of this algorithm can achieve a maximum acceleration ratio of 113.13. Comparative experiments conducted with varying data volumes revealed that this method significantly enhances the signal processing rate for passive bistatic radar. [ABSTRACT FROM AUTHOR]

Forward scattering radar has been widely used to classify human movements. To reduce concern of prolonged radiation exposure, Wi-Fi based passive scattering radar with bistatic topology is proposed. The movements include walking, bending, sitting, and kneeling. The enveloping algorithm applied to Wi-Fi based passive forward scattering radar signals has produced a comparable pattern to the ones from the active configuration. The features extracted from the frequency spectrum are also similar for both radar topologies. These led to comparable performance when classifying using artificial neural network. Hence, WiFi can effectively reduce the cost of radar sensors. [ABSTRACT FROM AUTHOR]

Copyright of Systems Engineering & Electronics is the property of Journal of Systems Engineering & Electronics Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Passive Bistatic Radar (PBR) has significant civilian and military applications due to its ability to detect low-altitude targets. However, the uncontrollable characteristics of the transmitter often lead to subpar target detection performance, primarily due to a low signal-to-noise ratio (SNR). Coherent accumulation typically has limited ability to improve SNR in the presence of strong noise and clutter. In this paper, we propose an adversarial learning-based radar signal enhancement method, called radar signal enhancement generative adversarial network (RSEGAN), to overcome this challenge. On one hand, an encoder-decoder structure is designed to map noisy signals to clean ones without intervention in the adversarial training stage. On the other hand, a hybrid loss constrained by L 1 regularization, L 2 regularization, and gradient penalty is proposed to ensure effective training of RSEGAN. Experimental results demonstrate that RSEGAN can reliably remove noise from target information, providing an SNR gain higher than 5 dB for the basic coherent integration method even under low SNR conditions. [ABSTRACT FROM AUTHOR]

Traditional target tracking is carried out based on the point measurements extracted from the radar resolution cells. This is not suitable for situations of low signal-to-noise ratio (SNR). In this paper, we aim to investigate the problem of the joint detection and tracking (JDT) of a target by directly using the received signals of passive multi-static radar without feeding the signals to matched filters. To this end, a novel likelihood function is proposed exploiting the statistical properties of coherent processing between the reference and surveillance signals. With such a likelihood function, the particle Bernoulli filter is employed to perform direct JDT (DJDT) of the target. A remarkable feature of the proposed method is that it is able to achieve satisfactory performance when the SNR of received signals is low. Furthermore, the proposed method cannot only achieve the existence and kinematic state of the target, but also the time-varying SNR of each receiver, which serves as an important input for sensor adjustment. The performance of the proposed method is verified via simulations. [ABSTRACT FROM AUTHOR]

In the case of multipath propagation for passive bistatic radar (PBR) using uncooperative frequency agile-phased array radar as an illuminator, a new direction-finding method is proposed to deal with the scenario where the coherent and uncorrelated signals are closely spaced or in the same direction. Firstly, spatial difference technique is used to eliminate uncorrelated signals. Then, in order to avoid the cross-terms effect and improve the resolution of coherent signal, the iterative adaptive method (IAA) is adopted for the rearranged spatial difference matrix. Finally, the direction of arrival (DOA) of the target signal is obtained by the reconstruction of the interference-plus-noise covariance matrix. Compared with previous studies, this method has better performance in the case of low signal-to-noise ratio (SNR) and limited number of snapshots. [ABSTRACT FROM AUTHOR]

Asan important means in low-altitude airspace surveillance, passive radar has been widely studied. With the increasing complexity of the low-altitude environment, the urgent need for radar's capability of automatic target recognition (ATR) emerges. In the field of ATR for passive radar, the method based on radar cross section (RCS) is an important direction for the simplicity of feature extraction. In this article, we exploit the compensated quasi-echo-power (CQEP), i.e., quasi-RCS, to realize ATR in passive radar. We propose an ATR method on the basis of the angular diversity. First, we divide the angular space, which consists of four components of the incident angle and scattering angle of electromagnetic wave, into multiple subspaces. Then, we build a subrecognizer in each angular subspace according to the CQEP distribution characteristics. Each receiving station of the multistatic passive radar recognizes targets in an angular subspace corresponding to its observation and outputs a preliminary decision. Based on the preliminary decisions of all receiving stations, a voting strategy is adopted to make the final decision on the unknown target class in the fusion center. Experimental results based on real-life target data show that the proposed method has a significant improvement on the average correct recognition rate with fusion of three receiving stations, which validates the proposed method. [ABSTRACT FROM AUTHOR]

A global navigation satellite system (GNSS)-based multistatic radar is explored for target localization and kinematic state estimation. Since any point on the earth can be illuminated by a minimum of four satellites of each GNSS constellation at any time, GNSS-based passive radars can be inherently considered multistatic radars. In this paper, a method for jointly estimating the target position and velocity by utilizing both the time delays and Doppler shifts has been proposed, and an analytical accuracy analysis is also provided. In the new method, the bistatic range and Doppler for each path are firstly estimated by the range-Doppler (RD) method, and then by using the bistatic ranges and Doppler shifts. The least squares method is applied to estimate the target position and velocity simultaneously. Compared with the precedent target localization and velocity estimation method, the proposed method achieves a better estimation result with simple procedures. Simulation results are provided to validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This article presents detailed geometric analyses of ground clutter in bistatic passive airborne radars. Analytic closed-form solutions are derived for finding the intersection of iso-ranges and iso-velocities. This allows clutter bistatic coordinates to be easily converted to its Cartesian coordinates. Based on those solutions, a theoretical clutter map in the bistatic coordinates can be calculated assuming uniform clutter distribution on the Earth’s surface. This is done by first converting a resolution cell in the bistatic coordinates into a corresponding cell in the Cartesian coordinates. Next, the power distribution in the bistatic coordinates is calculated taking into account range dependency, incident angles, and the radiation patterns of the transmitter and the receiver. The aim of this analysis is to characterize clutter in terms of expected mean power map rather than in terms of statistical distribution. The obtained results provide insights into the expected characteristics of clutter, which can be helpful in designing signal processing algorithms for ground moving target indication (GMTI) and synthetic aperture radar (SAR). The theoretical clutter distribution on the range-velocity map is compared with real-life data acquired with a Digital Video Broadcasting–Terrestrial (DVB-T)-based passive radar and good agreement between theory and measurement is presented. [ABSTRACT FROM AUTHOR]

Passive radar systems use illuminators of opportunity to illuminate targets instead of dedicated radar transmitters. The signals of opportunity have lower bandwidth than dedicated active radar systems, leading to poor downrange resolution. Multiple signals of opportunity can be coherently combined to increase the overall bandwidth of the system, and therefore create finer resolution images. These signals are usually separated in the frequency domain (non‐contiguous), which causes large unwanted grating lobe artefacts in the image when using back‐projection or Fourier transform based imaging. Additionally, these signals may originate from transmitters not located at the same position. A calibration method is developed to align the downrange responses and coherently combine the two signals. A compressive sensing‐based algorithm is used to combine the calibrated non‐contiguous frequency data, and is shown to mitigate the grating lobe artefacts that occur when using a back‐projection algorithm. This approach is validated with simulated and experimental data from a passive radar system tracking a commercial airline using two digital television (DTV) broadcast transmitters. [ABSTRACT FROM AUTHOR]

Active reconfigurable intelligent surfaces (RISs) are a novel and promising technology that allows controlling the radio propagation environment while compensating for the product path loss along the RIS-assisted path. In this letter, we consider the classical radar detection problem and propose to use an active RIS to get a second independent look at a prospective target illuminated by the radar transmitter. At the design stage, we select the power emitted by the radar, the number of RIS elements, and their amplification factor in order to maximize the detection probability for a fixed probability of false alarm and a common (among radar and RIS) power budget. An illustrative example is provided to assess the achievable detection performance, also in comparison with that of a radar operating alone or with the help of a passive RIS. [ABSTRACT FROM AUTHOR]

With the development of the JUpiter ICy moons Explorer (JUICE)/Radar for Icy Moons Exploration (RIME) [European Space Agency (ESA)] and Europa Clipper/Radar for Europa Assessment and Sounding: Ocean to Near-surface (REASON) [National Aeronautics and Space Administration (NASA)] instruments, designed to study the subsurface of the Galilean moons, interest has been growing to study the performances of sounding radar orbiting these bodies. In the presence of strong Jupiter’s radio emissions, probing in a passive mode using these emissions as the emitter is considered. However, radar performances in this bistatic mode are dependent on the entire geometry of observation: the position of the source of emission, the spacecraft trajectory, and on the region probed. The 3-D Simulations are necessary to estimate the performances of these measurements. We analyze the influence of the geometry of observation by approximating Jovian radio bursts as radio impulses, simulating the signal scattered by a point target in a realistic 3-D geometry and computing the resolution. This allows a preliminary identification of scenarios of observation best suited for this radar mode. The influence of the correct localization of Jupiter’s emissions on the synthetic aperture radar (SAR) image is investigated as well, and interest in recovering the true position of Jupiter’s source is highlighted. [ABSTRACT FROM AUTHOR]

Global navigation satellite system (GNSS)-based passive bistatic radar (PBR) has many advantages benefiting from the bistatic configuration and the excellent properties of the GNSS signals. In this article, the possibility of moving target indication (MTI) using a GNSS-based PBR is analyzed and illustrated by experiments. The power budget is first evaluated to investigate the capabilities and limitations of the GNSS-based PBR. Due to the low power density of GNSS signals, long-time integration is required to achieve long-range surveillance. In our previous work, a Radon Fourier transform (RFT)-based long-time integration algorithm has been proposed for GNSS-based PBR. However, the RFT-based methods are computationally inefficient. In this article, a novel MTI algorithm based on high frame rate image sequence (HFRIS) is introduced to the GNSS-based PBR. Benefiting from the avoiding of the iterative multidimensional parameter searching, it has a higher computational efficiency than the RFT-based methods. At the same time, the possibility of multistatic positioning for moving targets using the GNSS-based PBR is analyzed. It is shown that the absolute position of the target in three dimensions could be determined if at least three satellites are utilized to measure the range delay of the target return. To confirm our analysis, experiments are conducted which detects the airplanes using the GPS signals as illuminators of opportunity. The collected data are processed by both the RFT-based method and the HFRIS-based method. Both methods have successfully detected the airplane target at a distance of about 5 km and the HFRIS-based method shows a far better performance in terms of processing efficiency. The multistatic positioning experiment is also conducted and the estimated position of the target is well consistent with the values acquired by the flight record, which shows the potential of the GNSS-based PBR on multistatic operations. [ABSTRACT FROM AUTHOR]

The problem of single-channel reception of global positioning system (GPS) communication waveforms makes passive sensing of aerial target difficult because of forward scatter. This paper proposes a novel aerial target passive sensing method based on linear canonical transformation (LCT) using the forward scattered satellite communication waveforms. The proposed method firstly preprocesses the received signal based on the characteristics of the traditional satellite tracking loop and the forward scattered satellite communication waveforms to effectively suppress the interference of the direct wave through DC removal. Then, the Gaussian noise and multipath interference in the channel are suppressed by applying a rectangular window to its linear canonical domain. Finally, aerial target sensing is performed based on the peak value of signals in the linear canonical transform domain. The characteristic signal is constructed by analyzing the satellite communication waveforms. Combining the linear canonical transform with the matched filter (MF) to estimate the target parameter. Simulation results show that the proposed method can effectively perform the aerial target sensing by using satellite communication waveforms in the forward scatter scenario. [ABSTRACT FROM AUTHOR]

In a passive radar, when the reference antenna is set to receive a direct-path signal, target signals will be inevitably mixed in the reference channel due to the antenna pattern. In this case, adaptive clutter cancellation in the temporal domain will affect the target steering vector due to the correlation between the target signal in the reference and surveillance channels, which results in a direction of arrival (DOA) estimation bias. The spatial-domain adaptive clutter rejection will also cause a similar influence. To solve this problem, in this article, we derive and analyze the effect of the adaptive clutter rejection on the target steering vector. Two kinds of DOA estimation methods are hence proposed to correct the estimation bias. The applicable boundaries of these two methods are also discussed. Simulations and real radar data show that the proposed methods can correct the DOA bias caused by adaptive clutter rejection, thereby improving the location accuracy in a passive radar. [ABSTRACT FROM AUTHOR]

This article presents the pioneering results of successful target detection using a fully operational and cooperative 5G cellular network as a source of illumination in a passive radar system. The electromagnetic wave generated by the real-life base station allowed for remote sensing of a moving car in bistatic geometry, which shows the feasibility of passive radar in which new generation radio networks serve as an illuminator of opportunity. This article describes passive radar principles, the theoretical fundamentals of the 5G signal structure, and the proposed processing for 5G network-based passive radar. Also, the 5G passive radar demonstrator is described, and the trial results show the possibilities and limitations of using new radio standards in the context of passive radars. [ABSTRACT FROM AUTHOR]

Passive operation is an important operational concept for future airborne radar platforms. Successful target detection requires an understanding of the underlying clutter statistics in order to set the detection threshold accurately. In addition, clutter statistics are important for modeling of passive radar performance and simulation of passive bistatic radar to aid in the development of new target detection algorithms. In this article, the clutter statistics of data from an airborne platform are studied over a range of bistatic geometries and receive polarizations. The illuminator is a digital video broadcast-terrestrial (DVB-T) station and the collected data spans both ground and maritime regions. The key contributions include a study of amplitude statistics using a number of common distributions and understanding the impact of the reference signal quality in terms of the clutter statistics. [ABSTRACT FROM AUTHOR]

Intelligent reflecting surface (IRS) is a promising technology being considered for future wireless communications due to its ability to control signal propagation. This paper considers the joint active and passive beamforming problem for an IRS-assisted radar, where multiple IRSs are employed to assist the surveillance of multiple targets in cluttered environments. Specifically, we aim to maximize the minimum target illumination power at multiple target locations by jointly optimizing the active beamformer at the radar transmitter and the passive phase-shift matrices at the IRSs, subject to an upperbound on the clutter power at each clutter scatterer. The resulting optimization problem is nonconvex and solved with a sequential optimization procedure along with semidefinite relaxation (SDR). Simulation results show that additional line-of-sight (LOS) paths created by IRSs can substantially improve the radar robustness against target blockage. [ABSTRACT FROM AUTHOR]

In this article, we review and compare different methods for the localization of an illuminator of opportunity for passive radar systems employing cooperative targets. For assessment and comparison, we use numerical simulations and real-world radar measurements. To achieve reliable operation under real-world conditions, a correct and robust association of the bistatic radar target observations with ground truth information is necessary. We introduce a novel solution to this issue with an efficient preprocessing algorithm based on a planar approximation. [ABSTRACT FROM AUTHOR]

A new algorithm for passive bistatic radar (PBR) localization is proposed via joint exploitation of multiple illuminators of opportunity and measurements gathered by a colocated active radar. Ad-hoc constraints within the localization process are bestowed accounting for both a priori information on the PBR receive antenna main-beam size and the uncertainty characterizing active radar data, i.e., the root mean square error (RMSE) of range/bearing measurements. Hence, the estimation task is cast as an elliptic positioning problem, according to the constrained least squares framework. The resulting non-convex optimization problem is globally solved providing a closed-form estimate in Cartesian coordinates. The performance of the proposed estimator, in terms of RMSE, exhibits sensible improvement with respect to counterparts. The proposed technique is also applied to the case of a dynamic scenario for a bi-sensor surveillance system, where the active rotating platform acquires measurements at each scanning period. The results show the localization performance improvement achieved when the system is complemented with a PBR staring in a specific search sector of interest. [ABSTRACT FROM AUTHOR]

This article addresses the problem of clutter cancelation for slowly moving target detection and localization in multichannel passive radar onboard mobile platforms. A post-Doppler space-time adaptive processing (STAP) approach is exploited in the case of an angle-dependent imbalance affecting the receiving channels. While the clutter suppression capability is ensured by the adaptivity of space-time filtering, different solutions are compared, aimed at recovering the detection performance losses associated with channel calibration errors. A space-time generalized-likelihood ratio test (GLRT) scheme is considered, where the steering vector is not specified in the spatial domain, resulting in a noncoherent integration of target echoes across the receiving channels. This is compared with a fully coherent GLRT scheme where echoes from the stationary scene are exploited for the proper calibration of spatial steering vector mismatch. The first scheme proves to be a simple solution for target detection in the passive radar case, offering comparable clutter cancelation capability. The second scheme, at the expense of an additional stage, offers slightly better detection performance and preserves target direction-of-arrival (DoA) estimation capability. Finally, the STAP scheme is employed for the maximum-likelihood estimation of target DoA, evaluating the role of the steering vector calibration against the negative impact of channel imbalance. The effectiveness of the proposed approaches is tested against both simulated and experimental data from a DVB-T-based mobile passive radar. [ABSTRACT FROM AUTHOR]

Bistatic airborne radar has excellent performance due to the separate transmitter and receiver, but its clutter distribution is usually non‐stationary, which causes the performance of the traditional Space time adaptive processing (STAP) method to fail. Herein, firstly a bistatic airborne radar clutter signal model established, followed by an analysis of its clutter distribution characteristics in detail, and finally a bistatic airborne radar space–time compensation STAP method based on adaptive segmentation is proposed. The method first uses the distribution characteristics of the peak spectral centre in the first pulse data of the airborne radar to adaptively segment the clutter data, including extremely non‐stationary, severely non‐stationary, and non‐stationary clutter regions. Then the clutter data are compensated based on the estimation value of the space–time peak spectrum centre. Finally, each range section is processed by using STAP, and the detected target Doppler frequency is adaptively moved. Simulation results verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The detection and tracking performance of passive radar systems can be enhanced by exploiting multiple emitters and one receiver site by allowing for multiple bistatic geometries. This article investigates the measurement accuracy of passive radar systems that employ the advanced television system committee (ATSC 1.0) signal as a signal of opportunity. The monostatic and bistatic modified Cramér–Rao lower bound for the range and velocity measurements are derived as a quantitative way to evaluate the performance variation when exploiting multiple transmitters. The effect of 3D target position on the signal-to-noise ratio, with respect to stationary transmitters and receiver, is highlighted. Furthermore, signal-to-interference-and-noise ratio modeling is included by considering the direct signal interference suppression performance for a set of transmitters. An example in Columbus, Ohio, for a single receiver and multiple digital television transmitters that are spatially distributed is presented to find the optimal emitter that yields the best range and velocity measurement in the analyzed area. Target-tracking experiments show an agreement between the optimal emitter map and the tracking quality for the set of transmitters. [ABSTRACT FROM AUTHOR]

Despite increasing threats from hostile drones, the conventional active radar system remains inappropriate for urban surveillance purposes. The digital video broadcasting-terrestrial (DVB-T) signal exhibits a wide bandwidth and high transmit power compared with FM or WiFi signals, and hence enables the design of simple, low-cost passive radar with wide coverage areas. In this paper, a DVB-T system is employed to construct a passive radar surveillance system, and its performance is assessed experimentally in terms of detecting airplanes and small drones. For this purpose, a simple passive radar is implemented using high-gain antennas and low-cost RF receivers. After the DVB-T signals received through passive channels are processed, target-detection scenarios are carried out for flying airplanes and drones. [ABSTRACT FROM AUTHOR]

In some radar applications, neither the channel parameters nor the transmitted signal are known a-priori at the radar receiver. As such, both the transmitted signal as well as the channel parameters are random variables. Given the knowledge of distributions of the unknown parameters, we propose a maximum a-posteriori (MAP) ratio test (MAPRT) detector that incorporates this knowledge into its decision making process. This MAP approach is a generalization of past approaches such as the generalized likelihood ratio test (GLRT) detectors, where the estimates of the unknown parameters are obtained using maximum likelihood (ML) estimation. Assuming no knowledge of transmit waveforms, we derive the test statistics for bi-static and multi-static radar systems, when the noise power is both known and unknown. For the case of known noise variance in the bi-static radar system, we derive an exact closed-form expression for the probability of false alarm (PFA) and an approximate expression for the probability of detection (PD). For the multi-static case with known noise power, we derive upper bounds on PFA and PD. Numerical simulations verify the accuracy of the derived expressions and demonstrate that the proposed MAPRT detector performs significantly better than the GLRT-based detectors, especially when the signal-to-noise ratio (SNR) associated with the surveillance channel or sample size assumes small values. [ABSTRACT FROM AUTHOR]

Various correlation-based receivers have been proposed in passive bistatic and active monostatic radar exploiting orthogonal frequency-division multiplexing communications signals, but too little has been dedicated to establishing their relations and advantages over each other. Accordingly, this article provides an analytical comparison of the common filters in such waveform sharing scenarios, along with a performance analysis regarding three criteria: computational complexity, signal-to-interference-plus-noise-ratio, and resilience to ground clutter. The last two especially assess the possible detrimental effects of the random sidelobes (or pedestal) induced by the data symbols in the range-Doppler map. Although simulations show that none of the filters performs unanimously better, the ones employing circular correlations globally evidence attractive results. [ABSTRACT FROM AUTHOR]

This article deals with the problem of target detection in a passive multiple-input multiple-output (MIMO) radar network involving noncooperative illuminators of opportunity (IOs) and geographically dispersed multichannel receivers. The signal model considers the direct-path interference (DPI). We employ the Rao test to solve the problem and derive a closed-form detector. Then, by considering the properties of the ambiguity functions of most IO waveforms, an approximated version of the detector with a simpler form is derived. Two detectors in the case of an active MIMO network are also provided as the upper bounds of the passive situations. Moreover, considering target echo signal fluctuation, we have analyzed the performance of the detectors in terms of probability of miss-detection when being used in a multistatic configuration and have specified the conditions under which the full diversity gain is achieved. Numerical results verify the effectiveness of the proposed detectors and demonstrate that the proposed detectors have performance very close to the active situation. [ABSTRACT FROM AUTHOR]

In this paper, we propose a new framework of target classification for a passive coherent location(PCL) radar network. The framework uses radar cross sections(RCSs) obtained from multiple bistatic radars, and is computationally more efficient compared with the conventional method that uses time-varying RCSs obtained from a monostatic radar. Firstly, we construct the training set of the bistatic RCS distribution of each target using the scenario-based method and a PCL radar network with multiple transmitters and a receiver. Next, assuming that a test sequence consists of bistatic RCSs, we classify each target using statistical hypothesis test algorithms, such as Z-test, Wilcoxon test, and sign test. The proposed framework demonstrated better performance than the conventional method, in terms of computational efficiency. [ABSTRACT FROM AUTHOR]

In passive radar network (PRN), the receiver placement optimisation which has the ability to improve the coverage performance attracts much attention recently. In this study, the K-coverage performance is considered since the pre-condition of deghosting in a radar network is that the target has to be covered by $K\left({K \ge 3} \right)$KK≥3 bistatic pairs. Thus, a K-coverage-based receiver placement optimisation is formulated, in which a weighted M-centre model and the required radar cross section (RCS) for target detection are involved. Moreover, in order to solve this high dimensional optimisation problem, an iterative method which is based on K-order Voronoi algorithm and neighbourood search is proposed. Finally, the proposed method shows its effectiveness in solving the K-coverage optimisation problem of PRN via simulations. Specially, the probability of K-coverage is up to 99.8% with the optimal placement. [ABSTRACT FROM AUTHOR]

This paper addresses the exploitation of global navigation satellite systems as opportunistic sources for the joint detection and localization of vessels at sea in a passive multistatic radar system. A single receiver mounted on a proper platform (e.g., a moored buoy) can collect the signals emitted by multiple navigation satellites and reflected from ship targets of interest. This paper puts forward a single-stage approach to jointly detect and localize the ship targets by making use of long integration times (tens of seconds) and properly exploiting the spatial diversity offered by such a configuration. A proper strategy is defined to form a long-time and multistatic range and Doppler (RD) map, where the total target power can be reinforced with respect to, in turn, the case in which the RD map is obtained over a short dwell and the case in which a single transmitter is employed. The exploitation of both the long integration time and the multiple transmitters can greatly enhance the performance of the system, allowing counteracting the low-power budget provided by the considered sources representing the main bottleneck of this technology. Moreover, the proposed single-stage approach can reach superior detection performance than a conventional two-stage process where peripheral decisions are taken at each bistatic link and subsequently the localization is achieved by multilateration methods. Theoretical and simulated performance analysis is proposed and also validated by means of experimental results considering Galileo transmitters and different types of targets of opportunity in different scenarios. Obtained results prove the effectiveness of the proposed method to provide detection and localization of ship targets of interest. [ABSTRACT FROM AUTHOR]