Search

The production of edge-glued boards is one of the possibilities of using European beech wood for products with higher added value. European beech is highly abundant in the forests of Central Europe, but it is a wood species that has specific characteristics that affect the efficiency of processing. The dimensions and quality of the raw material are determined by the standard. This study analyzes the influence of the quality of European beech raw material on the quantitative and qualitative yield during the production of cross-sections used to produce edge-glued boards. Results show that the effect of class (raw material quality) on the quantity of timber produced is not remarkable. For classes III.B and III.C, the most prevalent factors diminishing yield were the quality and extent of red false heartwood, as well as cracks. This study confirmed that superior raw material quality has a positive impact on the yield of blanks with the highest quality.

Reaction wood is a wood defect arising during the growth of the tree in the part of the trunk that is under tension (hardwood tree species) or compression (coniferous tree species). Beech (Fagus sylvatica L.) tension wood has different anatomical and chemical characteristics than normal (opposite) wood. The difference in density is conditioned by the percentage of the gelatinous layer (G-layer). Fibre cells in reaction beech wood have a different cell wall structure and a different chemical composition. Tension wood cannot be detected by the naked eye. It is only possible to assume its occurrence based on the macroscopic characteristics of the logs, such as a woolly surface, taper or eccentric pith, and so forth. However, these are imprecise and unreliable methods that have minimal effectiveness, especially when shortening the length of the log for cut-outs. This study aimed to create a unique chemical reagent for the detection of tension wood in logs and timber and wood products immediately. The present research can contribute to the mitigation of flaws resulting from the reaction of wood in timber production while addressing noticeable constraints in manufacturing, such as energy resources and the availability of wood raw materials. This can be achieved through the efficient identification of reaction wood in materials. The colour change is only temporary and will fade over time. After the chemical reagent has dried on the surface, the surface can be milled. The colour change extends to a depth of approx. of 3 to 5 mm.

Reaction wood is a wood defect arising during the growth of the tree in the part of the trunk that is under tension (hardwood tree species) or compression (coniferous tree species). Beech (Fagus sylvatica L.) tension wood has different anatomical and chemical characteristics than normal (opposite) wood. The difference in density is conditioned by the percentage of the gelatinous layer (G-layer). Fibre cells in reaction beech wood have a different cell wall structure and a different chemical composition. Tension wood cannot be detected by the naked eye. It is only possible to assume its occurrence based on the macroscopic characteristics of the logs, such as a woolly surface, taper or eccentric pith, and so forth. However, these are imprecise and unreliable methods that have minimal effectiveness, especially when shortening the length of the log for cut-outs. This study aimed to create a unique chemical reagent for the detection of tension wood in logs and timber and wood products immediately. The present research can contribute to the mitigation of flaws resulting from the reaction of wood in timber production while addressing noticeable constraints in manufacturing, such as energy resources and the availability of wood raw materials. This can be achieved through the efficient identification of reaction wood in materials. The colour change is only temporary and will fade over time. After the chemical reagent has dried on the surface, the surface can be milled. The colour change extends to a depth of approx. of 3 to 5 mm.

The article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine wood grown in the northern part of Pomeranian region in Poland. The specimens were selected taking into consideration the radial angle of the growth rings. During each drying mode, 25 pieces of wood with dimensions (thickness, width, length) of 0.03 m, 0.2 m, and 1.5 m, respectively, were dried. The total color change (ΔE) after drying process and color saturation (h*) before and after drying processes of the wood surface was determined using the normalized CIELAB methods. The obtained results indicated that the color change of the pine wood surface increased simultaneously with the intensification of the drying process. However, the normalized wood quality after drying under intensive drying process conditions remained within the standard limits. The application of intensive drying process conditions remarkably changes the surface color of the obtained material, while remarkably reducing the drying process duration.

The article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine wood grown in the northern part of Pomeranian region in Poland. The specimens were selected taking into consideration the radial angle of the growth rings. During each drying mode, 25 pieces of wood with dimensions (thickness, width, length) of 0.03 m, 0.2 m, and 1.5 m, respectively, were dried. The total color change (ΔE) after drying process and color saturation (h*) before and after drying processes of the wood surface was determined using the normalized CIELAB methods. The obtained results indicated that the color change of the pine wood surface increased simultaneously with the intensification of the drying process. However, the normalized wood quality after drying under intensive drying process conditions remained within the standard limits. The application of intensive drying process conditions remarkably changes the surface color of the obtained material, while remarkably reducing the drying process duration.

This study focused on the impact of the wood sawing pattern on 50 mm thick beech timber, followed by cross-cutting on the 3 m long, 50 × 50 mm beech blanks. The study analyzed two methods of cutting patterns of beech blanks (parallel to the surface of the timber and parallel to the grain fiber of the timber) regarding yield values and the size of longitudinal warping after air-drying. The yield values were higher (from 65.14 to 72.70 %) when producing long beech blanks using the method of sawing parallel to the timber’s axis (B) compared to parallel to the edge of the blank (from 60.38 to 68.40 %). Results showed that a crucial factor for choosing the cutting method (A or B) is the taper of the logs. For blanks with a taper ≥ 1.3 cm.m-1, it is more advantageous in terms of longitudinal warping and yield to use the method of sawing parallel to the timber's axis.

This study focused on the impact of the wood sawing pattern on 50 mm thick beech timber, followed by cross-cutting on the 3 m long, 50 × 50 mm beech blanks. The study analyzed two methods of cutting patterns of beech blanks (parallel to the surface of the timber and parallel to the grain fiber of the timber) regarding yield values and the size of longitudinal warping after air-drying. The yield values were higher (from 65.14 to 72.70 %) when producing long beech blanks using the method of sawing parallel to the timber’s axis (B) compared to parallel to the edge of the blank (from 60.38 to 68.40 %). Results showed that a crucial factor for choosing the cutting method (A or B) is the taper of the logs. For blanks with a taper ≥ 1.3 cm.m-1, it is more advantageous in terms of longitudinal warping and yield to use the method of sawing parallel to the timber's axis.