Search

Shear horizontal surface acoustic wave (SH-SAW) biosensors measure the reaction of capture antibodies immobilized on the sensing surface to capture test molecules (antigens) by using the change in SH-SAW propagation characteristics. SH-SAW displacement exists not only on the SH-SAW propagating surface, but also partially penetrates the specimen liquid to a certain depth, which is determined by the liquid properties of the specimen and the operating frequency of the SH-SAW. This phenomenon is called viscosity penetration. In previous studies, the effect of viscosity penetration was not considered in the measurement of SH-SAW biosensors, and the mass or viscosity change caused by the specific binding of capture antibodies to the target antigen was mainly used for the measurement. However, by considering the effect of viscosity penetration, it was found that the antigen-antibody reaction could be measured and the detection characteristics of the biosensor could be improved. Therefore, this study aims to evaluate the detection properties of SH-SAW biosensors in the surface height direction by investigating the relationship between molecular dimensions and SH-SAW propagation characteristics, which are pseudo-changed by varying the diameter of gold nanoparticles. For the evaluation, we introduced a layer parameter defined by the ratio of the SH-SAW amplitude change to the SH-SAW velocity change caused by the antigen-antibody reaction. We found a correlation between the layer parameter and pseudo-varied molecular dimensions. The results suggest that SH-SAW does not only measure the mass and viscosity but can also measure the size of the molecule to be detected. This shows that SH-SAW biosensors can be used for advanced functionality.

Herein, we present an alternative approach to obtain a highly sensitive and stable self-powered biosensor that was used to detect D-fructose as proof of concept.In this platform, we perform a two-step process, viz. self-charging the biosupercapacitor for a constant time by using D-fructose as fuel and using the stored charge to realize the detection of D-fructose by performing several polarization curves at different D-fructose concentrations. The proposed BSC shows an instantaneous power density release of 17.6 mW cm -2 and 3.8 mW cm -2 in pulse mode and at constant load, respectively. Moreover, the power density achieved for the self-charging BSC in pulse mode or under constant load allows for an enhancement of the sensitivity of the device up to 10 times (3.82 ± 0.01 mW cm -2 mM -1 , charging time = 70 min) compared to the BSC in continuous operation mode and 100 times compared to the normal enzymatic fuel cell. The platform can potentially be employed as a self-powered biosensor in food or biomedical applications., (Copyright © 2020 Elsevier B.V. All rights reserved.)

This review summarizes the bioelectrocatalytic properties of d-fructose dehydrogenase (FDH), while taking into consideration its enzymatic characteristics. FDH is a membrane-bound flavohemo-protein with a molecular mass of 138 kDa, and it catalyzes the oxidation of d-fructose to 5-keto-d-fructose. The characteristic feature of FDH is its strong direct-electron-transfer (DET)-type bioelectrocatalytic activity. The pathway of the DET-type reaction is discussed. An overview of the application of FDH-based bioelectrocatalysis to biosensors and biofuel cells is also presented, and the benefits and problems associated with it are extensively discussed., (Copyright © 2019 Elsevier B.V. All rights reserved.)

In this paper we present a new method to electrodeposit highly porous gold (h-PG) onto a polycrystalline solid gold electrode without any template. The electrodeposition is carried out by first cycling the electrode potential between +0.8 and 0 V in 10 mM HAuCl 4 with 2.5 M NH 4 Cl and then applying a negative potential for the production of hydrogen bubbles at the electrode surface. After that the modified electrode was characterized in sulfuric acid to estimate the real surface area ( A real ) to be close to 24 cm 2 , which is roughly 300 times higher compared to the bare gold electrodes (0.08 cm 2 ). The electrode was further incubated overnight with three different thiols (4-mercaptobenzoic acid (4-MBA), 4-mercaptophenol (4-MPh), and 4-aminothiophenol (4-APh)) in order to produce differently charged self-assembled monolayers (SAMs) on the electrode surface. Finally a fructose dehydrogenase (FDH) solution was drop-cast onto the electrodes. All the modified electrodes were investigated by cyclic voltammetry both under nonturnover and turnover conditions. The FDH/4-MPh/h-PG exhibited two couples of redox peaks for the heme c 1 and heme c 2 of the cytochrome domain of FDH and as well as a well pronounced catalytic current density (about 1000 μA cm -2 in the presence of 10 mM fructose) due to the presence of -OH groups on the electrode surface, which stabilize and orientate the enzyme layer on the electrode surface. The FDH/4-MPh/h-PG based electrode showed the best analytical performance with an excellent stability (90% retained activity over 90 days), a detection limit of 0.3 μM fructose, a linear range between 0.05 and 5 mM, and a sensitivity of 175 ± 15 μA cm -2 mM -1 . These properties were favorably compared with other fructose biosensors reported in the literature. The biosensor was successively tested to quantify the fructose content in food and beverage samples. No significant interference present in the sample matrixes was observed.

Amperometric biosensors were constructed for the simultaneous detection of lactate enantiomers. The enantioselectivity of the sensor is based on NAD-dependent l- and d-lactate dehydrogenases that, respectively, oxidize l- and d-lactates into pyruvate. The NADH formed during the enzymatic reduction was catalytically oxidized at Meldola's blue-adsorbed mesoporous electrodes. Stable amperometric measurements were performed in a two-electrode system using Ag|AgCl|sat. KCl as a counter electrode via a salt bridge. The response of the sensor reached a pseudo-steady state within 60 s. The agreement of the sensitivities for l- and d-lactates and the pseudo-steady-state characteristics of the sensors demonstrate that the current is strongly influenced by the diffusion of lactates at the edge of the electrode, enabling reproducible measurements. The pseudo steady-state characteristics are also realized at the chip-type electrode. The sensor was successfully applied for the detection of d- and l-lactates in horse serum.

A method to stably immobilize microbes on electrodes was developed. Resting cells of Methylobacterium extorquens AM1(MeAM1) were caged within multiwalled carbon nanotubes (MWNTs)by adding the cells to a water dispersion of MWNTs then allowing the resulting mixture to dry on electrodes. The MeAM1-MWCNTs electrode thus obtained displayed excellent activities in the bidirectional bioelectrocatalysis due to formate dehydrogenase(s) in the resting cells; formate oxidation and carbon dioxide reduction proceeded at steady-state catalytic current densities of 0.6 ± 0.1 and -0.8 ± 0.1 mA cm -2 , respectively, using methyl viologen as mediator under very mild conditions (pH 7.0, atmospheric pressure, and 37 °C). In addition, the catalytic signal was stable for more than one week under continuous operation., (Copyright © 2018 Elsevier Inc. All rights reserved.)

We performed numerical simulations on an extremely fast, mediated, electron transfer-type bioelectrocatalytic reaction using a microband electrode. The simulations under fast-enzyme-kinetics conditions predicted that the decrement of the current density by increaseing the microband thickness would effectively improve the upper limit of detection. These predictions were accurate for an ultrathin-ring with thickness of 100 nm and gold leaf with thickness of 10 μm electrodes, acting as novel amperometric glucose sensors with FAD-dependent glucose dehydrogenase. The gold leaf electrode provided pseudo-steady-state currents which were proportional to the glucose concentration up to a concentration of 20 times higher than the mediator concentration.

Non-catalytic direct electron transfer (DET) signal of Compound I of horseradish peroxidase (POD) was first detected at 0.7 V on POD/carbon nanotube mixture-modified electrodes. Excellent performance of DET-type bioelectrocatalysis was achieved with POD immobilized with glutaraldehyde on Ketjen Black (KB)-modified electrodes for H 2 O 2 reduction with an onset potential of 0.65 V (vs. Ag | AgCl | sat. KCl) without any electrode surface modification. The POD-immobilized KB electrode was found to be suitable for detecting H 2 O 2 with a low detection limit (0.1 μM at S/N = 3) at -0.1 V. By co-immobilizing glucose oxidase (GOD) and POD on the KB-modified electrode, a bienzyme electrode was constructed to couple the oxidase reaction of GOD with the DET-type bioelectrocatalytic reduction of H 2 O 2 by POD. The amperometric detection of glucose was performed with a high sensitivity (0.33 ± 0.01 μA cm -2 μM -1 ) and a low detection limit (2 μM at S/N = 3).

The creation of electron transfer (ET) chains based on the defined arrangement of enzymes and redox proteins on electrode surfaces represents an interesting approach within the field of bioelectrocatalysis. In this study, we investigated the ET reaction of the flavin-dependent enzyme fructose dehydrogenase (FDH) with the redox protein cytochrome c (cyt c). Two different pH optima were found for the reaction in acidic and neutral solutions. When cyt c was adsorbed on an electrode surface while the enzyme remained in solution, ET proceeded efficiently in media of neutral pH. Interprotein ET was also observed in acidic media; however, it appeared to be less efficient. These findings suggest that two different ET pathways between the enzyme and cyt c may occur. Moreover, cyt c and FDH were immobilized in multiple layers on an electrode surface by means of another biomacromolecule: DNA (double stranded) using the layer-by-layer technique. The biprotein multilayer architecture showed a catalytic response in dependence on the fructose concentration, indicating that the ET reaction between both proteins is feasible even in the immobilized state. The electrode showed a defined response to fructose and a good storage stability. Our results contribute to the better understanding of the ET reaction between FDH and cyt c and provide the basis for the creation of all-biomolecule based fructose sensors the sensitivity of which can be controlled by the layer preparation.

Effects of the electrode poential on the activity of an adsorbed enzyme has been examined by using copper efflux oxidase (CueO) as a model enzyme and by monitoring direct electron transfer (DET)-type bioelectrocatalysis of oxygen reduction. CueO adsorbed on bare Au electrodes at around the point of zero charge (E(pzc)) shows the highest DET activity, and the activity decreases as the adsorption potential (E(ad); at which the enzyme adsorbs) is far from E(pzc). We propose a model to explain the phenomena in which the electrostatic interaction between the enzyme and electrodes in the electric double layer affects the orientation and the stability of the adsorbed enzyme. The self-assembled monolayer of butanethiol on Au electrodes decreases the electric field in the outside of the inner Helmholtz plane and drastically diminishes the E(ad) dependence of the DET activity of CueO. When CueO is adsorbed on bare Au electrodes under open circuit potential and then is held at hold potentials (E(ho)) more positive than E(pzc), the DET activity of the CueO rapidly decreases with the hold time. The strong electric field with positive surface charge density on the metallic electrode (σ(M)) leads to fatal denaturation of the adsorbed CueO. Such denaturation effect is not so serious at E(ho)<

The pseudo-steady-state current due to a mediated enzymatic reaction on a microelectrode is characterized on the basis of theoretical analysis and numerical simulation. The steady-state current is proportional to substrate concentration when the enzymatic reaction is considerably faster than substrate mass transport via nonlinear diffusion. Under such conditions, the reaction plane, where the mass flow of the substrate is converted to that of the mediator, exists near the electrode surface. The steady-state current increases as the diffusion coefficient of the substrate increases. In contrast, the diffusion coefficient and the concentration of the mediator have minor effects on the current. This difference can be explained on the basis of a change in the reaction plane location. When a sufficient amount of enzyme exists in a system, the system can be used as an amperometric biosensor, the response of which is independent of any change in enzyme activity.

A sensitive d-amino acid oxidase (DAAO)/peroxidase (POD) bienzyme biosensor is constructed, in which pentacyanoferrate-bound poly(1-vinylimidazole) polymer (PVI[Fe(CN)5]) is selected as a mediator. Reductive current of PVI[Fe(CN)5] related to the H2O2 concentration generated in the DAAO reaction was measured at -0.1V vs. Ag|AgCl with DAAO/POD/PVI[Fe(CN)5]-modified electrode. The result revealed that PVI[Fe(CN)5] is suitable as a mediator for this bienzyme system due to its appropriate formal potential and its extremely low reactivity against DAAO. The stability of DAAO was improved by adding free flavin adenine dinucleotide and the electrode composition was optimized for the detection of d-alanine. Nafion and ascorbate oxidase-immobilized films worked successfully to prevent severe interference from uric acid and ascorbic acid. The low detection limits of d-alanine (2μM) and d-serine (2μM) imply its possibility for the determination of extremely low concentration of d-amino acids in physiological fluids. The proposed bienzyme biosensor is proved to be capable of detecting d-amino acids in urine., (Copyright © 2013 Elsevier B.V. All rights reserved.)

Pentacyanoferrate-bound poly(1-vinylimidazole) (PVI[Fe(CN)5]) was selected as a mediator for amperometric creatinine determination based on the reductive H2O2 detection. Creatinine amidohydrolase (CNH), creatine amidohydrolase (CRH), sarcosine oxidase (SOD), peroxidase (POD), and PVI[Fe(CN)5] were crosslinked with poly(ethylene glycol) diglycidyl ether (PEGDGE) on a glassy carbon (GC) electrode for a creatinine biosensor fabrication. Reduction current was monitored at -0.1V in the presence of creatinine and O2. It is revealed that PVI[Fe(CN)5] is suitable as a mediator for a bioelectrocatalytic reaction of POD, since PVI[Fe(CN)5] neither reacts with reactants nor works as an electron acceptor of SOD. The amounts of PVI[Fe(CN)5], PEGDGE, and enzymes were optimized toward creatinine detection. Nafion as a protecting film successfully prevented the enzyme layer from interferences. The detection limit and linear range in creatinine determination were 12μM and 12-500μM (R(2)=0.993), respectively, and the sensitivity was 11mAcm(-2)M(-1), which is applicable for urine creatinine tests. The results of the creatinine determination for four urine samples measured with this proposed method were compared with Jaffe method, and a good correlation was obtained between the results., (Copyright © 2013 Elsevier B.V. All rights reserved.)

This paper describes a diffusion-controlled electrolysis of glucose with mediated bioelectrocatalysis at microdisk-electrodes. Under conditions of an extremely fast enzyme reaction, compared with the diffusion of glucose, the current in potential-step chronoamperometry reaches an almost steady state within 10 s, and is proportional to the glucose concentration. The current can be detected at +0.1 V (vs. Ag|AgCl) with 9,10-phenanthrenequinone as a mediator. The addition of carboxymethylcellulose increased the linear range up to 10 mM.

The mediated electro-enzymatic electrolysis systems based on the tricarboxylic acid (TCA) cycle reaction were examined on a micro-bulk electrolytic system. A series of the enzyme-catalyzed reactions in the TCA cycle was coupled with electrode reaction. Electrochemical oxidation of NADH was catalyzed by diaphorase with an aid of a redox mediator with a formal potential of -0.15 V vs. Ag|AgCl. The mediator was also able to shuttle electrons between succinate dehydrogenase and electrode. The charge during the electrolysis increased on each addition of dehydrogenase reaction in a cascade of the TCA cycle. However, the electrolysis efficiencies were close to or less than 90% because of the product inhibition. Lactate oxidation to acetyl-CoA catalyzed by two NAD-dependent dehydrogenases was coupled with the bioelectrochemical TCA cycle reaction to achieve the 12-electron oxidation of lactate to CO(2). The charge passed in the bioelectrocatalytic oxidation of 5 nmol of lactate was 4 mC, which corresponds to 70% of the electrolysis efficiency., (Copyright © 2012 Elsevier B.V. All rights reserved.)

To clarify the major factor caused by oxygen-enhancing charge production of Shewanella decolorationis NTOU1 towards a polarized anode, a series of experimental runs (i.e., with/without ambient air flushing and with/without ammonia addition as nitrogen source) were conducted in this study. Within 6-day of operation at +0.4 V vs. Ag|AgCl and starting with 35 mM of lactate, consistently the electrical charge production under the aerobic condition was higher than that under the anaerobic condition. In all the experimental runs, the values of nicotinamide adenine dinucleotide (NADH) production were found to be correlated positively and significantly with the charge production, but the highest Coulombic efficiency of 18% was observed under the anaerobic conditions without ammonia addition while the lowest charge production occurred. Those results indicate that NADH production enhanced by oxygen is the leading cause of the increase of the charge production, but the biomass production and the oxygen reduction would both consume NADH electrons and lead to lower electron recoveries. In addition, whether under constant aerobic or anaerobic, or alternating aerobic/anaerobic conditions, chronoamperometric results made it possible to rule out other factors, like lactate uptake rate or cell growth, which might increase the charge production under aerobic conditions. By using high performance liquid chromatography, some diffusive flavins (e.g., 0.5 microM of riboflavin) were found under the aerobic condition, but were not found under the anaerobic one. However, from results of cyclic voltammetry (CV), the signals of flavins were found to be approximately the same under both conditions. Although it is inferred that oxygen renders the flavins secreted extracellularly, that is not the major effect of oxygen for boosting the charge production. Furthermore, bound flavins under anaerobic condition were found to be effectively electrocatalytic according to sigmoidal CV result., (Copyright 2010 Elsevier B.V. All rights reserved.)

This paper describes the construction and characterization of a batch-type coulometric system for the detection of D-glucose using a novel FAD-dependent glucose dehydrogenase. In order to overcome the problem of interferents, such as ascorbate and urate, a potential-step method was proposed to separate the electrolysis reactions of interferents and D-glucose by selecting a mediator possessing an appropriate formal potential. The rapid oxidative consumption of the interferents proceeded in the first step, whereas the mediator and glucose remained reduced. In the second step, the mediator was immediately oxidized, and subsequent bioelectrocatalytic oxidation of D-glucose occurred with the aid of aldose 1-epimerase. In this study, potassium octacyanomolybdate (IV) with a formal potential of 0.6 V vs. Ag|AgCl was chosen as a mediator, and the first and second electrolysis potentials were set at 0.4 V and 0.8 V, respectively, by considering the heterogeneous electron-transfer kinetics and the potential window. The background-corrected response in charge corresponded to 99+/-2 % efficiency in terms of the amount of D-glucose.

A novel FAD-dependent glucose dehydrogenase (FAD-GDH) was found and its enzymatic property for glucose sensing was characterized. FAD-GDH oxidized glucose in the presence of some artificial electron acceptors, except for O2, and exhibited thermostability, high substrate specificity and a large Michaelis constant for glucose. FAD-GDH was applied to an amperometric glucose sensor with Fe(CN)6(3-) as a soluble mediator. The use of a relatively high concentration of Fe(CN)6(3-) resulted in a good linearity between the current response and the glucose concentration, taking into account a large Michaelis constant for Fe(CN)6(3-). The glucose sensor was completely insensitive to O2 and responded linearly to glucose up to 30 mM. Compared to glucose, the response to other saccharides was negligible. The sensor can be stored at room temperature in a desiccator for at least one month without any change in the response or activity.

Electrochemical studies on the applied aspects of quinoproteins are briefly reviewed. Catalytic reactions of quinoprotein enzymes can be connected to electrochemical reactions directly or by the mediation of molecules functioning as electron acceptors of the enzymes. Such an enzyme-electrochemical reaction is called bioelectrocatalysis. It provides a novel method of kinetic analysis of enzyme catalysis and even whole bacterial cell catalysis. The principle of bioelectrocatalysis is first described, then, the bioelectrocatalysis-based application of quinoproteins in biosensors is mentioned. Characteristics and performance of this type of biosensor is explained by citing our own work. Possible application in bioreactors and biofuel cells is also mentioned.

Escherichia coli cells, which contain apo-glucose dehydrogenase, were used in constructing a mediated amperometric glucose sensor. The E. coli modified glucose sensor, which was prepared by immobilizing E. coli cells behind a dialysis membrane on a carbon paste electrode containing 2,3-dimethoxy-5-methyl-1,4-benzoquinone (Q(0)), produced a current for the electrocatalytic oxidation of glucose with Q(0) as an electron transfer mediator only after the addition of a trace amount of pyrroloquinoline quinone (PQQ), the cofactor of the enzyme. This allows a novel method of glucose measurements free from the interference of the redox active substances, if contained, in a sample solution. The glucose sensor was insensitive to dioxygen; the currents measured under anaerobic and aerobic conditions, and even under dioxygen saturated conditions were almost the same in magnitude at a given concentration of glucose over the range of 0.2-10 mM. Response time of the glucose sensor was 2 min to attain 90% level of the steady-state current. The E. coli modified glucose sensor was reusable when treated with ethylenediaminetetraacetic acid (EDTA). When E. coli cells were lyophilized, they could be stored at room temperature in a dry box for more than six months without loss of the catalytic activity.