Search

Plant-derived cellulose biomaterials have recently been utilized in several tissue engineering applications. These naturally-derived cellulose scaffolds have been shown to be highly biocompatible in vivo, possess structural features of relevance to several tissues, and support mammalian cell invasion and proliferation. Recent work utilizing decellularized apple hypanthium tissue has shown that it possesses a pore size similar to trabecular bone and can successfully host osteogenic differentiation. In the present study, we further examined the potential of apple-derived cellulose scaffolds for bone tissue engineering (BTE) and analyzed their mechanical properties in vitro and in vivo. MC3T3-E1 pre-osteoblasts were seeded in cellulose scaffolds. Following chemically-induced osteogenic differentiation, scaffolds were evaluated for mineralization and for their mechanical properties. Alkaline phosphatase and Alizarin Red staining confirmed the osteogenic potential of the scaffolds. Histological analysis of the constructs revealed cell invasion and mineralization throughout the constructs. Furthermore, scanning electron microscopy demonstrated the presence of mineral aggregates on the scaffolds after culture in differentiation medium, and energy-dispersive spectroscopy confirmed the presence of phosphate and calcium. However, although the Young’s modulus significantly increased after cell differentiation, it remained lower than that of healthy bone tissue. Interestingly, mechanical assessment of acellular scaffolds implanted in rat calvaria defects for 8 weeks revealed that the force required to push out the scaffolds from the surrounding bone was similar to that of native calvarial bone. In addition, cell infiltration and extracellular matrix deposition were visible within the implanted scaffolds. Overall, our results confirm that plant-derived cellulose is a promising candidate for BTE applications. However, the discrepancy in mechanical properties between the mineralized scaffolds and healthy bone tissue may limit their use to low load-bearing applications. Further structural re-engineering and optimization to improve the mechanical properties may be required for load-bearing applications.

Articular cartilage from a material science point of view is a soft network composite that plays a critical role in load-bearing joints during dynamic loading. Its composite structure, consisting of a collagen fiber network and a hydrated proteoglycan matrix, gives rise to the complex mechanical properties of the tissue including viscoelasticity and stress relaxation. Melt electrospinning writing allows the design and fabrication of medical grade polycaprolactone (mPCL) fibrous networks for the reinforcement of soft hydrogel matrices for cartilage tissue engineering. However, these fiber-reinforced constructs underperformed under dynamic and prolonged loading conditions, suggesting that more targeted design approaches and material selection are required to fully exploit the potential of fibers as reinforcing agents for cartilage tissue engineering. In the present study, we emulated the proteoglycan matrix of articular cartilage by using highly negatively charged star-shaped poly(ethylene glycol)/heparin hydrogel (sPEG/Hep) as the soft matrix. These soft hydrogels combined with mPCL melt electrospun fibrous networks exhibited mechanical anisotropy, nonlinearity, viscoelasticity and morphology analogous to those of their native counterpart, and provided a suitable microenvironment for in vitro human chondrocyte culture and neocartilage formation. In addition, a numerical model using the p-version of the finite element method (p-FEM) was developed in order to gain further insights into the deformation mechanisms of the constructs in silico, as well as to predict compressive moduli. To our knowledge, this is the first study presenting cartilage tissue-engineered constructs that capture the overall transient, equilibrium and dynamic biomechanical properties of human articular cartilage.

An increasing number of studies have reported adverse tissue reactions around metal-on-metal (MM) hip implants. However, the origin and mechanisms of these reactions remain unclear. Moreover, the biological effects of nanometer-size chromium oxide particles, the predominant type of wear particles produced by MM implants, remain mostly unknown. The purpose of this study was to analyze the cytotoxic effects of clinically relevant nanometer-size chromium oxide particles on macrophage response in vitro. J774.A1 macrophages were cultured with either 60 nm or 700 nm commercially available Cr2 O3 particles at different concentrations. Two different particle sizes were analyzed to evaluate potential volume effects. Cell mortality was analyzed by light microscopy, flow cytometry (annexin V-fluorescein isothiocyanate and propidium iodide assay), and using a cell death detection enzyme-linked immunosorbant assay (ELISA). Tumor necrosis factor alpha (TNF-α), monocyte chemotactic protein-1 (MCP-1), and macrophage inflammatory protein-1 alpha (MIP-1α) release was measured by ELISA, and gene expression was analyzed by quantitative real-time PCR. Results showed that, at high concentrations, Cr2 O3 particles of both sizes can be cytotoxic, inducing significant decreases in total cell numbers and increases in necrosis. Results also suggested that these effects were dependent on particle volume. However, TNF-α, MCP-1, and MIP-1α cytokine release and gene expression remained low. Overall, this study demonstrates that nanometer-size particles of Cr2 O3 , a stable form of chromium oxide ceramic, have rather low cytotoxic effects on macrophages. Therefore, these particles may not be the main culprit in the initiation of the inflammatory reaction in MM periprosthetic tissues. However, other parameters (e.g., potential intracellular damage) remain to be investigated.

Fibrin, derived from key proteins involved in blood clotting (fibrinogen and thrombin), is a self-assembling biopolymer. The range of clinical applications and types of procedure that incorporate fibrin sealants is expanding. While fibrin sealants were initially, and continue to be, used for their hemostasis and tissue sealing properties, they have also been used more recently as a successful platform in various tissue regeneration applications necessitating cell and/or growth factor delivery. One of the primary reasons for this success is that fibrin provides a biocompatible physical structure and many of the important biological properties needed for successful tissue regeneration. In addition, these inherent biological properties can be enhanced by combining fibrin with other biomaterials (hence improving the overall biological and/or mechanical properties of the composite matrix) or by incorporating bioactive molecules to control cell proliferation, migration, or differentiation during tissue regeneration. This chapter summarizes key aspects of the composition, structure, as well as mechanical, fibrinolytic, and biological properties of fibrin as these characteristics influence its efficacy and performance. Applications of fibrin and fibrin-based biomaterials in tissue engineering and in clinical practice are also highlighted, with an emphasis on the use of fibrin as a delivery system for cells and bioactive molecules.

This study analyzed the ability of fibrin gels to deliver added recombinant transforming growth factor beta-1 (TGF-beta1) in a controlled manner and biologically active form. First, the effects of the amount of TGF-beta1 on the release kinetics were analyzed using a single fibrin gel formulation (fibrinogen complex (FC) at 25 mg/mL, thrombin at 2 IU/mL). Then, the effects of FC and thrombin concentrations were analyzed. Finally, to test the biological activity of the released TGF-beta1 from the gels, medium supernatants taken from gels at day 3 were used as culture medium for human mesenchymal stem cell (HMSC) monolayers. Cell proliferation was analyzed after staining with calcein dye, and changes in cell morphology were observed under fluorescence microscopy at days 1, 4, and 7. At day 7, HMSC chondrogenic differentiation was assessed by Alcian Blue staining and osteogenic differentiation by alkaline phosphatase activity and Alizarin Red staining. Results showed that TGF-beta1 added to fibrin gels was gradually released from the gels and increased with the amount of TGF-beta1 initially seeded, with a total of approximately 50% of the initial amount released by day 10 (with gels containing 25 mg/mL of FC and 2 IU/mL of thrombin). The release was lower with increasing FC concentrations, suggesting a binding affinity of TGF-beta1 with the FC component. Varying the thrombin concentration had a lesser effect. HMSC monolayers cultured with medium supernatants collected from gels at day 3 and containing released TGF-beta1 showed a change in morphology (squared to polygonal), lower cell proliferation, positive Alcian Blue staining but low levels of osteogenic differentiation markers. These results demonstrated that released TGF-beta1 was still bioactive and tended to induce mainly chondrogenic differentiation of the HMSC. Overall, the present study demonstrated that fibrin gels could be used as a carrier matrix for controlled release of bioactive TGF-beta1 by adjusting the concentrations of FC and thrombin in the gels.

Detailed characterization of wear particles is necessary to understand better the implant wear mechanisms and the periprosthetic tissue response. The purposes of the present study were to compare particle characteristics of current with older designs of metal-on-metal (MM) total hip replacements (THRs), and to determine the effect of implantation time on wear particle characteristics. Metal wear particles isolated from periprosthetic tissues from 19 patients with MM THRs of current and older designs and at different implantation times (very short, longer, and very long) were studied using transmission electron microscopy and energy dispersive X-ray analysis. The particles from the current design implants with implantation times of not more than 15 months (very short term) were almost exclusively round to oval chromium oxide particles. In all other cases, although the predominance was still round to oval chromium oxide particles, greater proportions of cobalt-chromium-molybdenum (Co-Cr-Mo) particles, mainly needle-shaped, were detected. Very long term THRs implanted for more than 20 years had the highest percentage of needle-shaped Co-Cr-Mo particles. Particle lengths were not markedly different between the different designs and implantation times except for the current design implants of not more than 15 months, which had a significantly smaller mean length of 39 nm. In conclusion, the implant design did not seem to have a significant influence on particle characteristics whereas the implantation time appeared to have the most effect on the particles. It should be noted that, because of the limited number of tissue retrievals available, some uncertainty remains regarding the generality of these findings.

The purpose of the present study was to compare wear particles isolated from metal-metal (MM) hip implants worn in an orbital bearing simulator with particles from similar MM total hip replacement (THR) implants worn in vivo. Comparison of these particles is important because it will help to assess the overall suitability of this type of hip simulator for reproducing in vivo wear and for producing physiological wear particles suitable for biological studies of in vitro cellular response. Commercial grade components made of ASTM F75 (cast) alloy were evaluated. Simulator tests were performed in 95% bovine calf serum with a 28-mm-diameter implant. Wear particles were collected from 0 to 0.25 million cycles (run-in wear period) and 1.75 to 2 million cycles (steady-state wear period). Tissues from seven patients with MM implants (surface replacement or stem type) were harvested at revision surgeries (after 1-43 months). Metal wear particles were isolated from serum lubricant or tissues using an enzymatic protocol that was previously optimized to minimize particle changes due to reagents. After isolation, particles were centrifuged, embedded in epoxy resin, and characterized by transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDXA). Results of EDXA on particles from the hip simulator primarily indicated a predominance of particles containing Cr and O but no Co (most likely chromium oxide particles), and fewer CoCrMo particles presenting varying ratios of Co and Cr. Image analysis of TEM micrographs demonstrated that the majority of the particles from the simulator were round to oval, but a substantial number of needle-shaped particles were also found, especially from 0 to 0.25 Mc. The particles generated from 0 to 0.25 Mc had an average length of 53 nm, whereas those generated from 1.75 to 2 Mc had an average length of 43 nm. In vivo, EDXA and TEM analysis of particles that were retrieved from two patients at 23 and 43 months respectively, revealed that they were the most comparable in composition, average length (57 nm), and shape to particles generated in the hip simulator during the run-in wear period. Because a large clinical retrieval study in the literature suggested that a run-in wear regime might occur in vivo for some 6-36 months, the fidelity of the simulator of the present study was strongly supported. However, some uncertainties existed, including the finding that the particles isolated from the other five patients generated from 1 month up to 15 months (shorter implantation times than the other two patients) were smaller and mostly contained only Cr and O (no Co). In the opinion of the authors, this particular very short term patient group was somewhat atypical. Therefore, despite these uncertainties, the present study was deemed to support the ability of the orbital bearing hip simulator to produce physiological wear particles.

There has been a revived interest in metal-metal total hip replacements because of their potential for improved wear performance compared with conventional metal-polyethylene implants. The aim of the present study was to characterize metal wear particles isolated from metal-metal hip simulator testing of various clinically relevant alloys and to analyze the effects of these alloys and the number of loading cycles on wear particle characteristics. Implants were manufactured using medical-grade cobalt-chromium-molybdenum (CoCrMo) alloys that were high-carbon wrought, low-carbon wrought, or cast (with solution annealing). Testing was performed in a MATCO orbital bearing hip simulator in 95% bovine calf serum. The wear particles were isolated from the serum at test periods of 0-0.25 million cycles (Mc) (run-in wear) and 1.75-2 Mc (steady-state wear) using an enzymatic protocol previously optimized to minimize particle changes due to reagents. Isolated particles embedded in epoxy resin were characterized by transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDXA). The EDXA results revealed the predominance of "lighter" particles containing Cr and O (most likely chromium oxide particles from the passivation layer) and fewer darker CoCrMo particles, with varying ratios of Co and Cr (possibly from carbides and from implant matrix material). More CoCrMo particles were observed with the low-carbon wrought alloy, but the majority of the particles for all three alloys was chromium oxides, especially for the 1.75-2 Mc test period. Image analysis of TEM micrographs revealed that for 0-0.25 Mc, there was up to 21% needle-shaped particles but that the majority remained round to oval in shape, reflecting the predominance of chromium oxide particles. Particle length averaged about 52 +/- 4 nm, with only small differences due to the alloy. For 1.75-2 Mc, most particles were round to oval in shape. They were even less needle-shaped than at 0.25 Mc, and they had a slightly smaller length, averaging 46 +/- 3 nm. In addition to characterizing the size and shape of particles from a MATCO simulator, this study is the first to demonstrate that particles that do not contain Co (presumably chromium oxides) can be predominant in the wear of metal-metal hip implants. It is therefore recommended that future in vitro and in vivo studies include the effects of these particles rather than just the effects of CoCrMo particles on the overall tissue response.

The aim of this study was to evaluate the cytotoxic and apoptotic effects of cobalt and chromium ions on macrophages in vitro, and analyze the implication of caspase-3 in the apoptotic pathway. J774 mouse macrophages (5 x 10(5) cells/ml) were exposed for up to 24 h to 0-10 ppm Co2+ and 0-500 ppm Cr3+. The cytotoxic effect of ions was measured by Trypan blue exclusion. DNA analysis on agarose gel was used as a specific test for detection of DNA fragmentation into oligonucleosomes that occurs in apoptotic cells. The proteolytic cleavage of poly(ADP-ribose)polymerase (PARP), closely associated with the induction of apoptosis, was also analyzed along with the appearance of the active fragment of caspase-3, implicated in several apoptosis pathways. Results demonstrated that both Co2+ and Cr3+ ions induce macrophage mortality in a dose-dependent manner. However, Co2+ is more toxic inducing a cell mortality up to 28% with only 10 ppm vs. 37% with 500 ppm of Cr3+. DNA analysis demonstrated that both Co2+ and Cr3+ ions induce DNA fragmentation, between 6-10 ppm Co2+ and 250-500 ppm Cr3+ after 24 h incubation. PARP cleavage and the appearance of caspase-3 active fragment were observed after 6 h with both Co+ and Cr3+ ions, with a stronger signal after 24 h and 10 ppm of Co2+ or 500 ppm of Cr3+. In conclusion, this study demonstrates that after 24 h incubation, both Co2+ and Cr3+ ions can induce macrophage mortality, and more specifically apoptosis. The results also suggest that apoptosis occurs via a caspase-3 pathway. However, the relative importance of necrosis and apoptosis and the effects of longer exposure times on the induction of macrophage death by these metal ions remain to be investigated.

The isolation of metal wear particles from hip simulator lubricants is important for understanding wear mechanisms and the tissue response to particulate material. Part I of this study demonstrated that isolation protocols involving digestion reagents can chemically attack metal-metal wear particles, reducing their size and changing their shape. In part II of this study, Co and Cr ion concentrations in solution after each digestion protocol were measured by flame atomic absorption spectrometry, and wear particle composition was determined by X-ray analysis spectra. The exposure of wear particles in water to alkaline solutions caused an increasing release of Cr ions in solution with alkaline concentration and time, and a corresponding decrease in particle Cr peak intensity on X-ray spectra. As a result, particles exposed to 12N KOH for 48 h displayed Co peaks and no Cr. In contrast, enzymatic protocols caused a release of Co ions in solution and a corresponding decrease in particle Co peak intensity on X-ray spectra, especially with sodium phosphate as a buffer. However, when isolating particles from 95% serum, there was an initial protective effect of serum proteins, presumably because of their binding to Co and Cr. As a result, the extent of Cr ion release from metal wear particles in 95% serum after alkaline treatments was diminished, although still present, whereas both enzymatic protocols resulted in a negligible release of Co and Cr ions into solution. Particle composition analysis after enzymatic treatments revealed the presence of chromium oxide particles and CoCrMo particles with variable Co/Cr ratios. After alkaline treatments, the chromium oxide particles increasingly disappeared with time and alkaline concentration, demonstrating a change in particle composition after these treatments. This study demonstrated that digestion reagents can induce chemical changes that affect particle composition. Of all the protocols tested, the enzymatic protocols were the least damaging to the particles and appeared to be the best compromise for isolation and characterization of metal particles, especially in 95% serum. Special care on the choice of buffers should be taken when isolating particles from a lower concentration of serum.

Isolation of metal wear particles from hip simulator lubricants or tissues surrounding implants is a challenging problem because of small particle size, their tendency to agglomerate, and their potential for chemical degradation by digestion reagents. To provide realistic measurements of size, shape, and composition of metal wear particles, it is important to optimize particle isolation and minimize particle changes due to the effects of the reagents. In this study (Part I of II), transmission electron microscopy (TEM) was used to examine and compare the effects of different isolation protocols, using enzymes or alkaline solutions, on the size and shape of three different types of cobalt-based alloy particles produced from metal-metal bearings. The effect on particle composition was examined in a subsequent study (Part II). Large particles (