Search

ObjectiveThe objective of this study is to compare drilling variables and torsional mechanical properties of rabbit femora after bicortical drilling with a 1.5-mm standard surgical drill bit, acrylic drill bit, and K-wire.Samples24 pairs of rabbit femora.MethodsAfter drilling under controlled axial displacement rate, each bone was biaxially loaded in compression followed by rapid external torsion to failure. Maximum axial thrust force, maximum drill torque, integral of force and displacement, change in temperature, maximum power spectral density of the torque signal, torque vibration, and torque and angle at the yield and failure points were collected. Pre- and postyield stiffness, yield and failure energies, and postyield energy were calculated.ResultsThe work required to drill through the cis- and transcortices (integral of force and displacement) was greater for the K-wire, followed by the acrylic and then standard drill bits, respectively. The K-wire demonstrated higher maximum torque than the drill bits at the ciscortex, and the force of drilling was significantly greater. The vibration data was greater with the acrylic and standard drill bits than the K-wire. There was no difference in torsional strength between drilling types.Clinical relevanceMechanical differences exist between different drill bits and K-wire and demonstrate that the K-wire is overall more damaging than the surgical drill bit.

Medial proximal sesamoid bones (PSBs) from Thoroughbred racehorses that did (Case) or did not (Control) experience unilateral biaxial PSB fracture were evaluated for bone volume fraction (BVF), apparent mineral density (AMD), tissue mineral density (TMD), and microdamage in Case fractured, Case contralateral limb intact, and Control bones. A majority of Case bones had a subchondral lesion with high microdamage density, and low BVF, AMD, and TMD. Lesion microdamage and densitometric measures were associated with training history by robust linear regression. Exercise intensity was negatively related to BVF (0.07 ≤ R2  ≤ 0.12) and positively related to microcrack areal density (0.21 ≤ R2  ≤ 0.29) in the lesion; however, in an undamaged site, the relationships were opposite in direction. Regardless of location, TMD decreased with event frequency for both Case and Control, suggesting increased bone remodeling with exercise. Measures of how often animals were removed from active training (layups) predicted a decrease in TMD, AMD, BVF, and microdamage at regions away from the lesion site. A steady-state compartment model was used to organize the differences in the correlations between variables within the data set. The overall conclusions are that at the osteopenic lesion site, repair of microdamage by remodeling was not successful (e.g., lower bone mass, increased damage, and lower mineralization) but that in regions away from the lesion remodeling successfully controlled damage (e.g., higher bone mass, less microdamage, and lower mineralization).

Distal limb injuries are common in racing horses and track surface properties have been associated with injury risk. To better understand how track surfaces may contribute to equine limb injury, we developed the first 3D computational model of the equine hoof interacting with a racetrack and simulated interactions with model representations of 1) a dirt surface and 2) an all-weather synthetic track. First, a computational track model using the Smoothed Particle Hydrodynamics (SPH) method with a Drucker-Prager (D-P) elastoplastic material model was developed. It was validated against analytical models and published data and then calibrated using results of a custom track testing device applied to the two racetrack types. Second, a sensitivity analysis was performed to determine which model parameters contribute most significantly to the mechanical response of the track under impact-type loading. Third, the SPH track model was coupled to a biomechanical model of the horse forelimb and applied to hoof-track impact for a horse galloping on each track surface. We found that 1) the SPH track model was well validated and it could be calibrated to accurately represent impact loading of racetrack surfaces at two angles of impact; 2) the amount of harrowing applied to the track had the largest effect on impact loading, followed by elastic modulus and cohesion; 3) the model is able to accurately simulate hoof-ground interaction and enables study of the relationship between track surface parameters and the loading on horses' distal forelimbs.

Bone "stress-whitens," becoming visibly white during mechanical loading, immediately prior to failure. Stress-whitening is known to make materials tougher by dissipating mechanical energy. A greater understanding of stress-whitening, both an optical and mechanical phenomenon, may help explain age-related increases in fracture risk that occur without changes in bone mineralization. In this work, we directly measure the optical properties of demineralized bone as a function of deformation and immersing fluid (with different hydrogen-bonding potentials, water, and ethanol). The change in refractive index of demineralized bone was linear: with deformation and not applied force. Changes in refractive index were likely due to pushing low-refractive-index fluid out of specimens and secondarily due to changes in the refractive index of the collagenous phase. Results were consistent with stress-whitening of demineralized bone previously observed. In ethanol, the refractive index values were lower and less sensitive to deformation compared with deionized water, corroborating the sensitivity to fluid hydration. Differences in refractive index were consistent with structural changes in the collagenous phase such as densification that may also occur under mechanical loading. Understanding bone quality, particularly stress-whitening investigated here, may lead to new therapeutic targets and noninvasive methods to assess bone quality.