Search

The present work deals with the optimization of the process parameters of in situ transesterification of dry spirogyra Algae–Jatropha powder along with engine efficiency and combustion analysis of the prepared biofuel. Three operational parameters, namely catalyst concentration (0–5 wt.%), methanol to dry algae–Jatropha curcas powder (v/v) (20–60%), and reaction time (60–180 min) at a constant reaction temperature of 50 °C, were selected. Response surface methodology (RSM) was used to design the experiments. The maximum biodiesel yield of 88.5% was obtained under the optimized conditions of a catalyst concentration of 3.396% (w/w), methanol/oil ratio of 19.86, and reaction time of 180 min. At varying loads, the performance and emissions of a diesel engine linked to a power source and fueled with various biodiesel mixes (Diesel, B5, B10, and B20) were tested. It was found that BSFC decreased as the applied load increased for all of the evaluated fuels. All of the biodiesel blends had greater BSFC than the diesel fuel. However, a substantial decrease in the emissions, including hydrocarbon (HC) and carbon monoxide (CO), was observed with the increase in NOx emissions. This method of preparing biodiesel will be beneficial in order to cater to the needs of the transportation sector because it has a lower energy consumption and less engine emissions. [ABSTRACT FROM AUTHOR]

Biodiesel production from different feedstocks is an effective method of resolving problems related to the fuel crisis and environmental issues. In this study, an adaptive neuro-fuzzy inference system (ANFIS) and the response surface methodology based Box-Behnken experimental design were used to model the parameters of biodiesel production for a jatropha-algae oil blend, including the molar ratio, temperature, reaction time, and catalyst concentration. A significant regression model with an R2 value of 0.9867 was obtained under a molar ratio of 6-12, KOH of 0-2% w/w, time of 60-180 min, and temperature of 35-55°C using response surface methodology (RSM). The ANFIS model was used to individually correlate the output variable (biodiesel yield) with four input variables. An R2 value of 0.9998 was obtained in the training. The results demonstrated that the developed models adequately represented the processes they described. [ABSTRACT FROM AUTHOR]

The production of biofuels as alternative energy source over fossil fuels has gained immense interest over the years as it can contribute significantly to reduce the greenhouse gas (GHG) emissions from energy production and utilization. Also with rapidly increasing fuel price and fall in oil wells, the present scenario forces us to look for an alternative source of energy that will help us in the operation of industrial as well as the transportation sector. The pulp mills in India are one of the many options. The pulp mills in India can help us to produce bio-fuels by thermo-chemical/biochemical conversion of black liquor and wood residues. These technologies include extraction of hemi-cellulose from wooden chips and black liquor, lignin from black liquor, methanol from evaporator condensates, biogas production from waste sludge, syngas production from biomass using gasification and bio-oil production from biomass using pyrolysis. The objective of this paper is to overview these emerging bio-refinery technologies that can be implemented in Indian Forest Industry to get bio-fuels, bio-chemicals and bio-energy to reduce GHG emissions. [ABSTRACT FROM AUTHOR]

Abstract: The present paper reports the results of the study of the effect of metal contaminants on the storage stability of Jatropha curcas biodiesel (JCB) with and without antioxidants. Taking 1,2,3 -Trihydroxybenzene/Pyrogallol (PY) as the most effective antioxidant based on the earlier work of the authors, JCB was mixed with different transition metals – Fe, Ni, Mn, Co and Cu in different concentrations. Induction period (IP) was measured using Rancimat method (EN 14112) as the stability parameter. Based on results, several correlations were developed for assessing the storage stability in terms of IP as a function of antioxidant, metal concentration and storage time. For the purpose of design of experiment, response surface methodology (RSM) has been used. From the experiments it is found that if metal concentration is 0 then, 200 g m−3 of PY is sufficient to make biodiesel stable for 6 months. If metal (Fe) concentration is 2 g m−3 or more, then 800 g m−3 PY is sufficient to make biodiesel stable for 5.5 months. The value of storage time for Ni, Mn, Co and Cu contaminated JCB is found as 3.62, 3.24, 2.76 and 2.07 months respectively if metal and antioxidants concentration is same in all the cases. The models developed by RSM shall be highly useful for predicting the optimum antioxidant concentration to achieve maximum storage stability of JCB as well as biodiesel from other resources under the conditions set for 3 factors (antioxidant concentration, metal concentration and time). [Copyright &y& Elsevier]

Abstract: Energy plays significant role in the development of a nation. The conventional sources, though exhausting and not environment friendly are being increasingly used. Looking at limited supplies and various environment problems associated with its uses, renewable energy sources are getting attention. Municipal solid waste [MSW] is getting importance in recent years. Having fewer disposal problems is being considered as valuable bio-energy resources. The MSW management involves collection, transportation, handling and conversion to energy by biological and thermal routes. The present paper reports the results of physical, proximate and TGA/DTA analysis, used to select the most appropriate method of energy conversion. Based on the energy potential available, the feasibility of energy conversion through biogas production using available waste has been carried out. The CDM benefits have also been considered. The cost of generation with and without CDM benefits is Rs. 1.36/- and Rs. 1.41/- per kWh respectively as compared to cost of energy from grid [Rs. 3.50/- per kWh]. Therefore power generation from MSW of Haridwar city using biomethanation conversion technology is feasible. [Copyright &y& Elsevier]

India is a nation with a diverse economy that requires tremendous resources to completely meet the desires of its compatriots in various sectors. In terms of energy resources and requirements, coal-based power plants can fulfill the bulk of these electricity needs. India is very reliant on coal, which is used in power plants as a primary energy source. However, the usage of coal energy at a higher level continuously pollutes the atmosphere. The Indian power market alone accounts for half of the country's CO2 emissions, which implies that significant action is needed to contain environmental pollution. Carbon Capture and Storage (CCS) is a bridging technique and feasible alternative for the carbon fired plant processing of CO2. However, the application of CCS in coal-fired power stations is still uncommon in the nation. At the UNFCCC Paris Summit, India committed to reduce its carbon emission intensity by approximately 30–33% by 2030. In this work, several CCS systems, possible CO2 origins, and emission levels in India are discussed. Various advanced methods for CO2 capture and separation are also highlighted. Furthermore, the current work discusses CCS situations and the applications of CCS in India along with its manifold challenges. [ABSTRACT FROM AUTHOR]

The production of biofuels (e.g., ethanol and biodiesel) requires a significant amount of water during feedstock production, transportation, and its conversion into biofuels. Therefore present study devoted to study the impact of biofuel production on water demand in Alberta. In scenario #1, it is assumed that ethanol is produced from both wheat and wheat straw and that biodiesel is produced from rapeseed. Scenario #2 proposes ethanol production from wheat only and biodiesel production from rapeseed. The water requirements for biofuel production in both scenarios are calculated for Alberta for the year 2025. Data on the current availability of water in Alberta indicate that the Athabasca, North Saskatchewan, and Peace River basins of northern Alberta have enough water to grow crops for the production of biofuels. In 2025, Alberta will have to produce 3,754 million liters of ethanol and 270 million liters of biodiesel to meet the projected levels. If biofuels are produced from the crops grown in the abovementioned northern river basins, the province of Alberta should be able to meet biofuel demand in 2025 sustainably. The water requirement from these river basins for biofuel production will increase to 5.2%, 0.6%, and 11.6%, respectively, of the natural flow in scenario #1 whereas, for scenario #2, the water requirement from these rivers basins will increase to 5.2%, 2.3%, and 16.1%, respectively, of natural flow. These increases in the requirements are much lower than the possible allowed withdrawal levels. [ABSTRACT FROM AUTHOR]