Search

P-band synthetic aperture radar (SAR) is sensitive to above-ground biomass (AGB) but retrieval accuracy has been shown to deteriorate in topographic areas. In boreal forest, the signal penetrates through the canopy to interact with the ground producing variations in backscatter depending on ground topography, forest structure, and soil moisture. Tomographic processing of multiple SAR images Tomographic SAR (TomoSAR) provides information about the vertical backscatter distribution. This article evaluates the use of P-band TomoSAR data to improve AGB retrievals from backscattered intensity by suppressing the backscattered signal from the ground. This approach can be used even when the tomographic resolution is insufficient to resolve the vertical backscatter profile. The analysis is based on P-band data from two campaigns: BioSAR-1 (2007) in Remingstorp, southern Sweden, and BioSAR-2 (2008) in Krycklan (KR), northern Sweden. BioSAR airborne data were also processed to correspond as closely as possible to future BIOMASS TomoSAR acquisitions, with BioSAR-2-based results shown. A power law AGB model using volumetric HV polarized backscatter performs best in KR, with training residual root mean-squared error (RMSE) of 30%–36% (27–33 t/ha) for airborne data and 38%–39% for simulated BIOMASS data. Airborne TomoSAR data suggest that both vertical and horizontal tomographic resolution are of importance and that it is possible to greatly reduce AGB retrieval bias when compared with airborne P-band SAR backscatter intensity-based retrievals. A lack of significant ground slopes in Remningstorp reduces the benefit of using TomoSAR data which performs similar to retrievals based solely on P-band SAR backscatter intensity. [ABSTRACT FROM AUTHOR]

Copyright of Canadian Journal of Remote Sensing is the property of Taylor & Francis Ltd and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

A new processing technique, i.e., ground cancellation, which removes the ground signal from a pair of interferometric synthetic aperture radar (SAR) images, is used to emphasize the response from above-ground targets. This technique is of particular interest when studying forest canopies using low-frequency signals able to reach the underlying ground, in which case the portion of the signal coming from the ground interferes with the recovery of information about the vegetation. We demonstrate that the power in ground-canceled P-band HV SAR data gives significantly higher correlations with above-ground biomass (AGB) than the interferometric images considered separately. In addition, a significant increase in the sensitivity of backscatter to AGB is observed. Ground-canceled power may then be modeled or regressed to estimate AGB; these possibilities are not discussed here as they will be the topic of forthcoming publications. The effectiveness of this technique is proven through simulations and analysis of real data gathered on tropical forests. The stability of the technique is analyzed under the digital terrain model and baseline control errors, and compensation strategies for these errors are presented. [ABSTRACT FROM AUTHOR]

Environmental conditions and seasonal variations affect the backscattered radar signal from a forest. This potentially causes errors in a biomass retrieval scheme using data from the synthetic aperture radar (SAR) data. A better understanding of these effects and the electromagnetic scattering mechanisms in forests is required to improve biomass estimation algorithms for current and upcoming P- and L-band SAR missions. In this paper, temporal changes in HH-, VV-, and HV-polarized P- and L-band radar backscatter and temporal coherence from a boreal forest site are analyzed in relation to environmental parameters. The radar data were collected from a stand of mature Norway spruce (Picea abies (L.) Karst.) with an above-ground biomass of approximately 250 tons/ha at intervals of 5 min from January to August 2017 using the BorealScat tower-based scatterometer. It was observed that subzero temperatures during the winters cause large variations (4 to 10 dB) in P- and L-band backscatter, for which the HH/VV backscatter ratio offered some mitigation. High wind speeds were also seen to cause deviations in the average backscatter at P-band due to decreased double-bounce scattering. Severe temporal decorrelation was observed at L-band over timescales of days or more, whereas the P-band temporal coherence remained high ($>$ 0.9) for at least a month neglecting windy periods. Temporal coherence at P-band was highest during night times when wind speeds are low. [ABSTRACT FROM AUTHOR]

A tomographic synthetic aperture radar (TomoSAR) represents a possible route to improved retrievals of forest parameters. Simulated orbital L-band TomoSAR data corresponding to the proposed Satellites for Observation and Communications-Companion Satellite (SAOCOM-CS) mission (1.275 GHz) are evaluated for retrieval of above-ground biomass in boreal forest. L-band data and biomass measurements, collected at the Krycklan test site in northern Sweden as part of the BioSAR 2008 campaign, are used to compare biomass retrievals from SAOCOM-CS to those based on SAOCOM SAR data. Both data sets are in turn compared with the corresponding airborne case, as represented by experimental airborne SAR through processing of the original SAR data. TomoSAR retrievals use a model involving a logarithmic transform of the volumetric backscatter intensity, $I_{\mathrm{ vol}}$ , defined as the total backscatter originating between 10 and 30 m above ground. SAR retrievals are obtained with slope-compensated intensity $\gamma ^{0}$ using the same model. It is concluded that tomography using SAOCOM-CS represents an improvement over an airborne SAR imagery, resulting in biomass retrievals from a single polarization (HH) having a 26%–30% root-mean-square error with a little to no impact from the look direction or the local topography. [ABSTRACT FROM AUTHOR]

This paper report experiences from the processing and mosaicking of 518 TanDEM-X image pairs covering the entirety of Sweden, with two single map products of above-ground biomass (AGB) and forest stem volume (VOL), both with 10 m resolution. The main objective was to explore the possibilities and overcome the challenges related to forest mapping extending a large number of adjacent satellite scenes. Hence, numerous examples are presented to illustrate challenges and possible solutions. To derive the forest maps, the observables backscatter, interferometric phase height and interferometric coherence, obtained from TanDEM-X, were evaluated using empirical robust linear regression models with reference data extracted from 2288 national forest inventory plots with a 10 m radius. The interferometric phase height was the single most important observable, to predict AGB and VOL. The mosaics were evaluated on different datasets with field-inventoried stands across Sweden. The root mean square error (RMSE) was about 21%-25% (27-30 tons/ha and 52-65 m3/ha) at the stand level. It was noted that the most influencing factors on the observables in this study were local temperature and geolocation errors that were challenging to robustly compensate against. Because of this variability at the scene-level, determinations of AGB and VOL for single stands are recommended to be used with care, as an equivalent accuracy is difficult to achieve for all different scenes, with varying acquisition conditions. Still, for the evaluated stands, the mosaics were of sufficient accuracy to be used for forest management at the stand level. [ABSTRACT FROM AUTHOR]

In this letter, the interferometric water cloud model (IWCM) is fit to 87 VV-polarized TanDEM-X acquisitions made between June 2011 and August 2014 over a boreal forest in Krycklan, northern Sweden, using a new method based on nonlinear least-squares optimization. A high-resolution digital terrain model is used as ground reference during interferometric synthetic-aperture radar (InSAR) processing and 26 stands with areas 1.5–22 ha and unaltered during the study period are studied. The dependence of biomass estimation performance, ground and vegetation backscatter coefficients ( \sigma ^0\mathrm {gr} and \sigma ^0\mathrm {veg} ), canopy attenuation ( \alpha ), and zero-biomass coherence ( \gamma _{0} ) on selected system and environmental parameters is studied. High correlation between the estimated biomass and reference biomass derived from in situ measurements is observed for all 87 acquisitions ( r between 0.81 and 0.93), while the root-mean-square difference is between 18% and 32% for all 43 acquisitions made in snow-free conditions and with heights-of-ambiguity (HOAs) between 36 and 150 m. Significant biomass estimation bias is observed for HOAs above 150 m and for some acquisitions over snow-covered forest. It is also observed that \sigma ^0\mathrm gr and \sigma ^0\mathrm veg are the largest for temperatures below 0 °C and with significant snow cover. For temperatures above 0 °C, \sigma ^0\mathrm gr appears independent of temperature, while \sigma ^0\mathrm veg shows a tendency to increase with temperature. Moreover, \gamma 0 decreases from just below 1 for HOAs around 40 m to around 0.8 for HOAs above 150 m. [ABSTRACT FROM PUBLISHER]

A model for aboveground biomass estimation from single-pass interferometric synthetic aperture radar (InSAR) data is presented. Forest height and canopy density estimates $\Delta h$ and \eta_0$, respectively, obtained from two-level model (TLM) inversion, are used as biomass predictors. Eighteen bistatic VV-polarized TanDEM-X (TDM) acquisitions are used, made over two Swedish test sites in the summers of 2011, 2012, and 2013 (nominal incidence angle: 41 ^{\circ} ; height-of-ambiguity: 32–63 m) . Remningstorp features a hemiboreal forest in southern Sweden, with flat topography and where 32 circular plots have been sampled between 2010 and 2011 (area: 0.5 ha; biomass: 42–242 t/ha; height: 14–32 m) . Krycklan features a boreal forest in northern Sweden, 720-km north–northeast from Remningstorp, with significant topography and where 31 stands have been sampled in 2008 (area: 2.4–26.3 ha; biomass: 23–183 t/ha; height: 7–21 m) . A high-resolution digital terrain model has been used as ground reference during InSAR processing. For the aforementioned plots and stands and if the same acquisition is used for model training and validation, the new model explains 65%–89% of the observed variance, with root-mean-square error (RMSE) of 12%–19% (median: 15%) . By fixing two of the three model parameters, accurate biomass estimation can also be done when different acquisitions or different test sites are used for model training and validation, with RMSE of 12%–56% (median: 17%) . Compared with a simple scaling model computing biomass from the phase center elevation above ground, the proposed model shows significantly better performance in Remningstorp, as it accounts for the large canopy density variations caused by active management. In Krycklan, the two models show similar performance. [ABSTRACT FROM PUBLISHER]

Methods to estimate forest biomass change have been investigated using experimental P-band synthetic aperture radar (SAR) data from the recent airborne campaigns BioSAR 2007 and BioSAR 2010 conducted over a hemiboreal test site in southern Sweden. Regression models based on backscatter change were developed using reference biomass change maps derived from high-density laser scanning data. Different regression models were developed for linear, square root, and logarithmic biomass change scales. The models were compared to the change maps based on laser data using twofold cross-validation, and estimation errors were evaluated using six 80 m by 80 m plots with detailed in situ measurements. The results indicate that the root-mean-square error of biomass change estimates based on P-band SAR backscatter data is about 15% or 20 t/ha. This suggests that not only clear-cuts but also growth and thinning can be measured. Simulations were performed in order to evaluate the possibility of using a spaceborne P-band SAR for measurements of forest biomass change. The simulations show that, with 64 equivalent number of looks (ENL) and a 50% change in biomass, it is possible to correctly indicate whether the forest has gained or lost biomass. Similarly, for a biomass loss of more than 75%, a correct indication of the sign of biomass change can be achieved with only 8 ENL. [ABSTRACT FROM PUBLISHER]

A new biomass retrieval model for boreal forest using polarimetric P-band synthetic aperture radar (SAR) backscatter is presented. The model is based on two main SAR quantities: the HV backscatter and the HH/VV backscatter ratio. It also includes a topographic correction based on the ground slope. The model is developed from analysis of stand-wise data from two airborne P-band SAR campaigns: BioSAR 2007 (test site: Remningstorp, southern Sweden, biomass range: 10–287 tons/ha, slope range: 0–4^\circ) and BioSAR 2008 (test site: Krycklan, northern Sweden, biomass range: 8–257 tons/ha, slope range: 0–19^\circ). The new model is compared to five other models in a set of tests to evaluate its performance in different conditions. All models are first tested on data sets from Remningstorp with different moisture conditions, acquired during three periods in the spring of 2007. Thereafter, the models are tested in topographic terrain using SAR data acquired for different flight headings in Krycklan. The models are also evaluated across sites, i.e., training on one site followed by validation on the other site. Using the new model with parameters estimated on Krycklan data, biomass in Remningstorp is retrieved with RMSE of 40–59 tons/ha, or 22–33% of the mean biomass, which is lower compared to the other models. In the inverse scenario, the examined site is not well represented in the training data set, and the results are therefore not conclusive. [ABSTRACT FROM PUBLISHER]

The structure of forests is important to observe for understanding coupling to global dynamics of ecosystems, biodiversity, and management aspects. In this paper, the sensitivity of X-band to boreal forest stem volume and to vertical and horizontal structure in the form of forest height and horizontal vegetation density is studied using TanDEM-X satellite observations from two study sites in Sweden: Remningstorp and Krycklan. The forest was analyzed with the Interferometric Water Cloud Model (IWCM), without the use of local data for model training, and compared with measurements by Airborne Lidar Scanning (ALS). On one hand, a large number of stands were studied, and in addition, plots with different types of changes between 2010 and 2014 were also studied. It is shown that the TanDEM-X phase height is, under certain conditions, equal to the product of the ALS quantities for height and density. Therefore, the sensitivity of phase height to relative changes in height and density is the same. For stands with a phase height >5 m we obtained an root-mean-square error, RMSE, of 8% and 10% for tree height in Remningstorp and Krycklan, respectively, and for vegetation density an RMSE of 13% for both. Furthermore, we obtained an RMSE of 17% for estimation of above ground biomass at stand level in Remningstorp and in Krycklan. The forest changes estimated with TanDEM-X/IWCM and ALS are small for all plots except clear cuts but show similar trends. Plots without forest management changes show a mean estimated height growth of 2.7% with TanDEM-X/IWCM versus 2.1% with ALS and a biomass growth of 4.3% versus 4.2% per year. The agreement between the estimates from TanDEM-X/IWCM and ALS is in general good, except for stands with low phase height. [ABSTRACT FROM AUTHOR]

Forest growth estimation is important in forest research and forest management, but complex to analyze in diverse forest stands. Twelve summertime TanDEM-X acquisitions from the boreal test site, Krycklan, in Sweden, with a known digital terrain model, DTM, have been used to study phase height and aboveground biomass change over 3.2 years based on the Interferometric Water Cloud Model, IWCM. The maximum phase height rate was determined to 0.29 m/yr, while the mean phase height rate was 0.16 m/yr. The corresponding maximum growth rate of the aboveground dry biomass, AGB, was 4.0 Mg/ha/yr with a mean rate of 1.9 Mg/ha/yr for 27 stands, varying from 23 to 183 Mg/ha. The highest relative AGB growth was found for young stands and high growth rates up to an age of 150 years. Growth rate differences relative a simplified model assuming AGB to be proportional to the phase height were studied, and the possibility to avoid a DTM was discussed. Effects of tree species, thinning, and clear cutting were evaluated. Verifications using in situ data from 2008 and a different in situ dataset combined with airborne laser scanning data from 2015 have been discussed. It was concluded that the use of multi-temporal TanDEM-X interferometric synthetic aperture radar observations with AGB estimates of each individual observation can be an important method to derive growth rates in boreal forests. [ABSTRACT FROM AUTHOR]