Search

Ultraviolet-C light-emitting diodes (UV-C LEDs) are an emerging technology for decontamination applications in different sectors. In this study, the inactivation of bacterial biofilms was investigated by applying an UV-C LED emitting at 280 nm and by measuring both the influence of the initial cell density (load) and presence of an extracellular matrix (biofilm). Two bacterial strains exposing diverging matrix structures and biochemical compositions were used: Pseudomonas aeruginosa and Leuconostoc citreum. UV-C LED irradiation was applied at three UV doses (171 to 684 mJ/cm 2 ) on both surface-spread cells and on 24-h biofilms and under controlled cell loads, and bacterial survival was determined. All surface-spread bacteria, between 10 5 and 10 9  CFU/cm 2 , and biofilms at 10 8  CFU/cm 2 showed that bacterial response to irradiation was dose-dependent. The treatment efficacy decreased significantly for L. citreum surface-spread cells when the initial cell load was high, while no load effect was observed for P. aeruginosa. Inactivation was also reduced when bacteria were grown under a biofilm form, especially for P. aeruginosa: a protective effect could be attributed to abundant extracellular DNA and proteins in the matrix of P. aeruginosa biofilms, as revealed by Confocal Laser Scanning Microscopy observations. This study showed that initial cell load and exopolymeric substances are major factors influencing UV-C LED antibiofilm treatment efficacy. KEY POINTS: • Bacterial cell load (CFU/cm 2 ) could impact UV-C LED irradiation efficiency • Characteristics of the biofilm matrix have a paramount importance on inactivation • The dose to be applied can be predicted based on biofilm properties., (© 2024. The Author(s).)

In freshwater ecosystem, phototrophic biofilms play a crucial role through adsorption and sequestration of organic and inorganic pollutants. However, extracellular polymeric substance (EPS) secretion by phototrophic biofilms exposed to metals is poorly documented. This work evaluated the physiological responses of phototrophic biofilms by exposing three microorganisms (cyanobacterium Phormidium autumnale, diatom Nitzschia palea and green alga Uronema confervicolum) to 20 and 200 μg L -1 of Cu or 60 and 600 μg L -1 of Zn, both individually and in combination. Analysis of metal effects on algal biomass and photosynthetic efficiency showed that metals were toxic at higher concentrations for these two parameters together and that all the strains were more sensitive to Cu than to Zn. U. confervicolum was the most impacted in terms of growth, while P. autumnale was the most impacted in terms of photosynthetic efficiency. In consequence to metal exposure at higher concentrations (Cu200, Zn600 and Cu200Zn600), a higher EPS production was measured in diatom and cyanobacterium biofilms, essentially caused by an overproduction of protein-like polymers. On the other hand, the amount of secreted polysaccharides decreased during metal exposure of the diatom and green alga biofilms. Size exclusion chromatography revealed specific EPS molecular fingerprints in P. autumnale and N. palea biofilms that have secreted different protein-like polymers during their development in the presence of Zn600. These proteins were not detected in the presence of Cu200 despite an increase of proteins in the EPS extracts compared to the control. These results highlight interesting divergent responses between the three mono-species biofilms and suggest that increasing protein production in EPS biofilms may be a fingerprint of natural biofilm against metal pollutants in freshwater rivers.

Aims: This study attempts to determine which of the exopolymeric substances are involved in the adherence and aggregation of a Bacillus licheniformis biofilm., Methods and Results: The involvement of extracellular proteins and eDNA were particularly investigated using DNase and proteinase K treatment. The permeability of the biofilms increased fivefold after DNase I treatment. The quantification of the matrix components showed that, irrespective to the enzyme tested, eDNA and amyloid-like polymers were removed simultaneously. Size-exclusion chromatography analyses supported these observations and revealed the presence of associated nucleic acid and protein complexes in the biofilm lysates. These data suggest that some extracellular DNA and amyloid-like proteins were closely interlaced within the matrix. Finally, confocal laser scanning microscopy imaging gave supplementary clues about the 3D organization of the biofilms, confirming that eDNA and exoproteins were essentially layered under and around the bacterial cells, whereas the amyloid-like fractions were homogeneously distributed within the matrix., Conclusion: These results confirm that some DNA-amyloid complexes play a key role in the modulation of the mechanical resistance of B. licheniformis biofilms., Significance and Impact of the Study: The study highlights the need to consider the whole structure of biofilms and to target the interactions between matrix components. A better understanding of B. licheniformis biofilm physiology and the structural organization of the matrix will strengthen strategies of biofilm control., (© 2017 The Society for Applied Microbiology.)

A novel approach to the quantification of extracellular polysaccharides in miniaturized biofilms presenting a wide variety of extracellular matrices was developed. The assay used the periodic acid-Schiff reagent and was first calibrated on dextran and alginate solutions. Then it was implemented on 24-h and 48-h biofilms from three strains known to produce different exopolymeric substances (Pseudomonas aeruginosa, Bacillus licheniformis, Weissella confusa). The assay allowed quantification of the total exopolysaccharides, taking into account possible interferences due to cells or other main expolymers of the matrix (eDNA, proteins)., (Copyright © 2016 Elsevier Inc. All rights reserved.)

Biofilms are ecosystems of closely associated bacteria encapsulated in an extracellular matrix mainly composed of polysaccharides and proteins. A novel approach was developed for in situ quantification of extracellular proteins (ePNs) in various bacterial biofilms using epicocconone, a natural, fluorescent compound that binds amine residues of proteins. Six commercial proteins were tested for their reaction with epicocconone, and bovine serum albumin (BSA) was selected for assay optimization. The optimized protocol, performed as a microassay, allowed protein amounts as low as 0.7 μg to as high as 50 μg per well to be detected. Addition of monosaccharides or polysaccharides (glucose, dextran or alginate) to the standard BSA solutions (0 to 250 μg ml(-1)) showed little or no sugar interference up to 2000 μg ml(-1), thus providing an assessment of the specificity of epicocconone for proteins. The optimized protocol was then applied to three different biofilms, and in situ quantification of ePN showed contrasted protein amounts of 22.1 ± 3.1, 38.3 ± 7.1 and 0.3 ± 0.1 μg equivalent BSA of proteins for 48-h biofilms of Pseudomonas aeruginosa, Bacillus licheniformis and Weissella confusa, respectively. Possible interference due to global matrix compounds on the in situ quantification of proteins was also investigated by applying the standard addition method (SAM). Low error percentages were obtained, indicating a correct quantification of both the ePN and the added proteins. For the first time, a specific and sensitive assay has been developed for in situ determination of ePN produced by bacterial cells. This advance should lead to an accurate, rapid tool for further protein labelling and microscopic observation of the extracellular matrix of biofilms.

A heterotrophic biofilm (B1) and a mixed autotrophic-heterotrophic biofilm (B2) were developed in an annular reactor and submitted to an erosion test in order to selectively detach top layers from the bottom layers. Densities of the basal layers were 5-fold higher and 3-fold higher than the densities of the entire biofilms B1 and B2, respectively. After extraction, EPS content in B1 biofilm was found higher in the basal layer (95 mg g⁻¹ VSS) compared to the top layer (30 mg g⁻¹ VSS), while B2 biofilm had a higher EPS content in the top layer (303 mg g⁻¹ VSS) compared to the basal layer (135 mg g⁻¹ VSS). Hydrophobic Interaction Chromatography (HIC) indicates that hydrophobic EPS (HEPS) in both biofilms reached 21% of EPS in basal cohesive layers, and remained slightly lower or identical (16-19%) in top detached biofilm layers. Strong interacting HEPS were found in a higher proportion in the mixed autotrophic-heterotrophic B2 which was also more diversified in terms of bacterial populations than the B1 heterotrophic biofilm. These results show that HEPS content correlates better with cohesive properties of the biofilm layers than global EPS content and that strong hydrophobic adhesion forces may be related to microbial populations such as the presence of nitrifiers., (Copyright © 2013 Elsevier B.V. All rights reserved.)

This study aimed to characterize biofilms from the paper industry and evaluate the effectiveness of enzymatic treatments in reducing them. The extracellular polymeric substances (EPS) extracted from six industrial biofilms were studied. EPS were mainly proteins, the protein to polysaccharide ratio ranging from 1.3 to 8.6 depending on where the sampling point was situated in the paper making process. Eight hydrolytic enzymes were screened on a 24-h multi-species biofilm. The enzymes were tested at various concentrations and contact durations. Glycosidases and lipases were inefficient or only slightly efficient for biofilm reduction, while proteases were more efficient: after treatment for 24 h with pepsin, Alcalase® or Savinase®, the removal exceeded 80%. Savinase® appeared to be the most adequate for industrial conditions and was tested on an industrial biofilm sample. This enzyme led to a significant release of proteins from the EPS matrix, indicating its potential efficiency on an industrial scale.

Extracellular Polymeric Substances (EPS) analysis was undertaken on three biofilms grown under different feeding conditions and offering diverging microbial activities and structural characteristics. EPS were extracted by a multi-method protocol including sonication, Tween and EDTA treatments and were characterized by size exclusion chromatography (SEC). Tween and sonication extracts presented higher EPS size diversity compared to EDTA extracts. EPS size diversity also increased with microbial functions within the biofilms and a specific 25-50 kDa cluster was identified only in extracts from biofilms presenting autotrophic activity. Another specific size cluster (180 kDa) occurred in Tween extracts provided from the mechanically stable biofilms. Such specific EPS appear as potential indicators for describing microbial and structural properties of biofilms. This study brings new elements for designing EPS fractionation and shows that size distribution analysis is an interesting tool to relate EPS diversity with macro-scale characteristics of biofilms., (© 2010 Elsevier Ltd. All rights reserved.)

Abstract: The high water recycling ratio used in some industries can cause nutrients to accumulate in the system, leading to thick, rapidly growing biofilms inducing detrimental effects. Nowadays, chemical treatments are widely used but the increasingly restrictive environmental regulations induce the necessity to take the environmental aspect into account in the choice of a suitable treatment. With this in mind, this study analyses a method for controlling thick, dense biofilm development by applying synergistic actions having low environmental impact, i.e., an enzymatic and a mechanical (shear stress) treatment well suited to industrial water networks. For that purpose, biofilms were grown on plastic plates set in a Couette–Taylor reactor (CTR) that was inoculated using a “white water” sampled from a paper industry network. Development of the biofilms was controlled by applying a constant continuous feeding with a high COD/N ratio of 20, a well-defined shear stress and an external aeration, those conditions leading to a well-controlled G-value and a γ S/O2 value close to 1, and consequently, to the development of thick mainly aerobic heterotrophic biofilms representative of that encountered in high loaded industrial water networks. Optimal operating conditions for biofilm treatments were determined considering the penetration time for the enzymatic treatment taking into account both internal and external mass transport (using Biot number calculation). In addition, an optimal shear stress increment of 2.5Pa was selected in order to maximise biofilm detachment while avoiding compression phenomena due to the mechanical treatment. The combined treatment led to an increase of 80% in biofilm mass removal (COD) compared to the enzymatic treatment alone and removed a large part of the basal layer of the biofilm, 80% reduction being observed in the support coverage. [Copyright &y& Elsevier]