Search

The fast depletion of conventional fuel supplies has forced the world to find suitable substitutes to overcome the expected energy crisis. Fossil fuels also contribute to global warming because of their harmful emissions. Biofuels are sustainable and environment friendly. Biodiesel can be sourced from both edible and non-edible oils to replace fossil fuels. To avoid a shortage of food supply, it is preferred to produce biodiesel from non-edible oils. In this research, Litchi chinensis seed oil (LSO) is used as a feedstock to synthesize biodiesel employing transesterification using a microwave oven. The catalyst, potassium hydroxide (KOH), used in this research was extracted from potato waste. Sundried potato waste was converted into ash. The produced ash is then dissolved in distilled water, leading to a 34% yield of KOH. The transesterification achieves a 92.9% conversion rate under the conditions: 30% microwave power utilization, a catalyst loading of 15% (W/W), a stirring speed of 700 RPM, and a methanol concentration of 70% (V/V) with an 8-min reaction time. Response surface methodology (RSM), in comparison with artificial neural networks (ANNs), has been utilized for the optimization of biodiesel yield, giving efficient results with errors of 0.003% for RSM and 0.005% for ANN. Consequently, the study reports optimized biodiesel yields of 92.9% (experimental), 93.27% (RSM), and 92.40% (ANN). Physicochemical properties such as kinematic viscosity (4.4 mm2/s) at 40°C, density (875kg/m3) at 15°C, cetane number (53.2), calorific value (38.8 MJ/kg), flash point (175°C), oxidative stability (6.1 h), and cold flow properties were determined with respect to the ASTM and EN standards. The findings reveal that biofuels primarily support Sustainable Development Goals (SDGs) 7 and 13, with the prime focus on "affordable and clean energy" and "climate action," respectively. [ABSTRACT FROM AUTHOR]

This document is a corrigendum for an article titled "Microwave-assisted transesterification of Litchi chinensis seed oil using extracted KOH from potato waste for sustainable development." The corrigendum addresses errors in the funding statement and acknowledgments of the original article. The authors apologize for the errors and state that they do not affect the scientific conclusions of the article. The corrigendum also includes a note from the publisher stating that the claims expressed in the article are solely those of the authors and do not necessarily represent the views of their affiliated organizations or the publisher. The article was written by authors from various institutions in Pakistan, Saudi Arabia, and Australia. [Extracted from the article]

In this investigation, biodiesel was produced from Moringa oleifera oil through a transesterification process at operating conditions including a reaction temperature of 60 °C, catalyst concentration of 1% wt., reaction time of 2 h, stirring speed of 1000 rpm and methanol to oil ratio of 8.50:1. Biodiesel blends, B10 and B20, were tested in a compression ignition engine, and the performance and emission characteristics were analyzed and compared with high-speed diesel. The engine was operated at full load conditions with engine speeds varying from 1000 rpm to 2400 rpm. All the performance and exhaust pollutants results were collected and analyzed. It was found that MOB10 produced lower BP (7.44%), BSFC (7.51%), and CO2 (7.7%). The MOB10 also reduced smoke opacity (24%) and HC (10.27%). Compared to diesel, MOB10 also increased CO (2.5%) and NOx (9%) emissions. [ABSTRACT FROM AUTHOR]

In this study, waste cooking oil (WCO) was used as a feedstock for biodiesel production, where the pretreatment of WCO was performed using mineral acids to reduce the acid value. The response surface methodology (RSM) was used to create an interaction for different operating parameters that affect biodiesel yield. The optimised biodiesel yield was 93% at a reaction temperature of 57.50 °C, catalyst concentration 0.25 w/w, methanol to oil ratio 8.50:1, reaction stirring speed 600 rpm, and a reaction time of 3 h. Physicochemical properties, including lower heating value, density, viscosity, cloud point, and flash point of biodiesel blends, were determined using American Society for Testing and Materials (ASTM) standards. Biodiesel blends B10, B20, B30, B40, and B50 were tested on a compression ignition engine. Engine performance parameters, including brake torque (BT), brake power (BP), brake thermal efficiency (BTE), and brake specific fuel consumption (BSFC) were determined using biodiesel blends and compared to that of high-speed diesel. The average BT reduction for biodiesel blends compared to HSD at 3000 rpm were found to be 1.45%, 2%, 2.2%, 3.09%, and 3.5% for B10, B20, B30, B40, and B50, respectively. The average increase in BSFC for biodiesel blends compared to HSD at 3500 rpm were found to be 1.61%, 5.73%, 8.8%, 12.76%, and 18% for B10, B20, B30, B40, and B50, respectively. [ABSTRACT FROM AUTHOR]