Search

The rapid, inexpensive, and on-site detection of bacterial contaminants using highly sensitive and specific microfluidic sensors is attracting substantial attention in water quality monitoring applications. Cell-imprinted polymers (CIPs) have emerged as robust, cost-effective, and versatile recognition materials with selective binding sites for capturing whole bacteria. However, electrochemical transduction of the binding event to a measurable signal within a microfluidic device to develop easy-to-use, compact, portable, durable, and affordable sensors remains a challenge. For this paper, we employed CIP-functionalized microwires (CIP-MWs) with an affinity towards E. coli and integrated them into a low-cost microfluidic sensor to measure the conductometric transduction of CIP–bacteria binding events. The sensor comprised two CIP-MWs suspended perpendicularly to a PDMS microchannel. The inter-wire electrical resistance of the microchannel was measured before, during, and after exposure of CIP-MWs to bacteria. A decline in the inter-wire resistance of the sensor after 30 min of incubation with bacteria was detected. Resistance change normalization and the subsequent analysis of the sensor's dose-response curve between 0 to 109 CFU/mL bacteria revealed the limits of detection and quantification of 2.1 × 105 CFU/mL and 7.3 × 105 CFU/mL, respectively. The dynamic range of the sensor was 104 to 107 CFU/mL where the bacteria counts were statistically distinguishable from each other. A linear fit in this range resulted in a sensitivity of 7.35 μS per CFU/mL. Experiments using competing Sarcina or Listeria cells showed specificity of the sensor towards the imprinted E. coli cells. The reported CIP-MW-based conductometric microfluidic sensor can provide a cost-effective, durable, portable, and real-time solution for the detection of pathogens in water. [ABSTRACT FROM AUTHOR]

Molecular imprinting has advanced towards synthesizing whole-cell imprints of microorganisms such as bacteria on various sensor surfaces including wire electrodes, quartz crystal microbalances, and microparticles (MPs). We recently introduced cell-imprinted polymers (CIPs) coated on MPs, called CIP-MPs, for bacteria recovery from water. In this paper, we have advanced towards rapid fluorometric Escherichia coli (E. coli) detection by applying fluorescent magnetic CIP-MPs, which were captured by soft ferromagnetic microstructures integrated into a microfluidic channel. The shape of ferromagnetic microstructures was optimized numerically to enhance the magnetophoretic accumulation of CIP-MPs in the microchannel. The device was then fabricated and the flow rate required to enhance bacteria capturing efficiency by CIP-MPs was determined. Decreasing the flow rate reduced the flow-induced drag and increased the interactions between the bacteria and imprinted CIP cavities. Fluorescent imaging of the accumulated CIP-MPs was done before and after bacteria capturing to quantify the changes in the fluorescence intensity as E. coli cells were captured by CIP-MPs in the microchannel. The dose-response curve of the sensor at 0–109 CFU/mL bacterial counts was obtained. Using the 3- and 10-sigma methods on the dose-response curve, the limits of detection (LOD) and quantification (LOQ) of the sensor were determined to be 4 × 102 and 3 × 103 CFU/mL, respectively, within a dynamic range of 102–107 CFU/mL. Lastly, the specificity of the CIP-MPbased sensor towards E. coli was tested and confirmed using Sarcina as a non-specific target bacterium. In summary, our developed sensor offers a promising approach for rapid and low-cost detection of bacteria in water and is suitable for development of portable and durable all-polymeric sensors for point-of-need detection. [Display omitted] • Magnetic cell imprinted polymer microparticles (CIP-MPs) and their capturing optimization in a microchannel. • Rapid E. coli detection by fluorescent magnetic CIP-MPs in a microfluidic device. • Low-cost and durable all-polymeric sensor for bacteria detection in water. • Sensor limit of detection at 4 × 102 CFU/mL and limit of quantification at 3 × 103 CFU/mL. • Sensor specificity towards E. coli , providing a reliable tool for targeted bacterial quantification. [ABSTRACT FROM AUTHOR]