Search

Objective: To investigate the biomechanical effect of C1 lateral mass-C2 pedicle screw-rod (C1LM-C2PS) fixation with and without transverse connectors (TC) in an atlantoaxial instability (AAI) model., Methods: Ten freshly frozen cadaveric specimens were tested using an industrial robot under the following conditions: intact model, AAI model, C1-C2 model, C1-C2 with one TC model, and C1-C2 with two TCs model. Three types of motion, flexion-extension (FE), lateral bending (LB), and axial rotation (AR), were applied (1.5 Nm) to the specimens. The range of motion (ROM) and neutral zone (NZ) between C1 and C2 in all directions were measured., Results: Compared with those of the intact and AAI models, the C1-C2 ROM and NZ of all instrumented groups were decreased significantly in each direction of loading motion (P < 0.05). The mean FE ROM in the no TC, 1 TC, and 2 TC groups was 2.12° ± 0.41°, 2.29° ± 0.42°, and 2.04° ± 0.69°, respectively (P = 0.840, 0.981, 0.628, respectively); the mean LB ROM in the 3 intervention groups was 1.26° ± 0.67°, 1.02° ± 0.51° and 1.03° ± 0.57°, respectively (P = 0.489, 0.501, 1.000, respectively). During AR, the ROM and NZ of the no TC group (3.19° ± 0.89° and 1.51° ± 0.42°) were significantly reduced by more than 60% compared with those in the 1 (0.98° ± 0.28° and 0.40° ± 0.11°) and 2 TC groups (1.17° ± 1.69° and 0.42° ± 0.61°) (P < 0.001). Two TCs were equivalent for all loading motions to 1 TC (P > 0.05)., Conclusions: Adding TCs to C1LM-C2PS can effectively decrease the axial rotation ROM and enhance the stability of C1-C2 segment. Therefore, it is necessary to use TC-strengthened C1 lateral mass -C2 pedicle screw-rod fixation in patients with instability of C1-C2., (Copyright © 2020 Elsevier Inc. All rights reserved.)

Objective: To report the technical nuances and clinical outcomes of posterior atlantoaxial facet joint reduction, fixation and fusion (AFRF) technique as a revision procedure for BI and AAD patients with failed suboccipital decompression and large occipital bone defect., Patients and Methods: We reviewed 32 patients with BI and AAD who were misdiagnosed as a simple Chiari malformation and received a suboccipital decompression surgery before admission. All patients underwent AFRF as a revision surgery. The separating, fusing, opacifying and false-coloring-volume rendering (SFOF-VR) technique was used to identify the course of the VA. Clinical and radiological outcomes were assessed after revision surgeries., Results: Clinical symptoms improved in all patients. The postoperative atlantodens interval, Wackenheim line and clivus-canal angle significantly improved (all P < 0.01). Intraoperative dural tear and cerebrospinal fluid leakage occurred in 3 patients and were managed by suture repair and lumbar drain. Abnormal VA was identified in 7 patients and no VA injury occurred with the aid of SFOF-VR technique. The average follow-up was 19.1 months and atlantoaxial bone fusion was confirmed in 31 patients., Conclusion: For BI and AAD patients with failed suboccipital decompression, revision surgery is challenging. Occipitocervical fixation and posterior midline bone grafting are rather difficult due to the large occipital bone defect. The current study demonstrated that the posterior AFRF is a simple, safe and highly effective technique in revision surgery for such cases. For VA variations, the SFOF-VR technique is an effective tool to delineate the course VA., Competing Interests: Declaration of Competing Interest None., (Copyright © 2020. Published by Elsevier B.V.)

Objective: To evaluate the usefulness of 3-dimensional (3D) printed models as an aid for the treatment of complex CVJ anomalies., Methods: 3D printed models were fabricated for 21 patients with complex CVJ anomalies, including vertebral artery anomaly, thin C2 pedicle, vertical atlantoaxial facet joint, or rotational dislocation combined with atlantoaxial dislocation and basilar invagination. Preoperative planning, surgical simulation, and intraoperative reference were achieved using the 3D model during the surgical treatment. The usefulness of 3D printed models, and postoperative clinical and radiological outcomes were assessed., Results: Direct posterior reduction and atlantoaxial fixation were achieved in 19 patients. Transoral odontoidectomy followed by posterior fixation was implemented for 2 patients with vertical facet joint and rotational dislocation. All screws were safely inserted with no complication, and 90% patients achieved a >60% reduction of both horizontal and vertical dislocation. Clinical symptoms improved in all patients, with the averaged Japanese Orthopedic Association scores increasing from 11.14 to 14.43 (P < 0.01)., Conclusions: The patient-specific 3D printed model would be an effective tool for evaluation of the reducibility of the atlantoaxial dislocation and basilar invagination, decision making in choosing the optimal surgical approach and way of fixation, and precise placement of the screw while protecting the vertebral artery and spinal cord. The risk of neurovascular injury was minimized, and encouraging outcomes were achieved with the aid of this technique., (Copyright © 2019 Elsevier Inc. All rights reserved.)