Search

Diamond-like carbon (DLC) coatings doped with bioactive elements of silver (Ag) and copper (Cu) have been receiving increasing attention in the last decade, particularly in the last 5 years, due to their potential to offer a combination of enhanced antimicrobial and mechanical performance. These multi-functional bioactive DLC coatings offer great potential to impart the next generation of load-bearing medical implants with improved wear resistance and strong potency against microbial infections. This review begins with an overview of the status and issues with current total joint implant materials and the state-of-the art in DLC coatings and their application to medical implants. A detailed discussion of recent advances in wear resistant bioactive DLC coatings is then presented with a focus on doping the DLC matrix with controlled quantities of Ag and Cu elements. It is shown that both Ag and Cu doping can impart strong antimicrobial potency against a range of Gram-positive and Gram-negative bacteria, but this is always accompanied so far by a reduction in mechanical performance of the DLC coating matrix. The article concludes with discussion of potential synthesis methods to accurately control bioactive element doping without jeopardising mechanical properties and gives an outlook to the potential long-term impact of developing a superior multifunctional bioactive DLC coating on implant device performance and patient health and wellbeing. Multi-functional diamond-like carbon (DLC) coatings doped with bioactive elements of silver (Ag) and copper (Cu) offer great potential to impart the next generation of load-bearing medical implants with improved wear resistance and strong potency against microbial infections. This article provides a critical review of the state-of-the-art in Ag and Cu doped DLC coatings, beginning with an overview of the current applications of DLC coatings in implant technology followed by a detailed discussion of Ag/Cu doped DLC coatings with particular focus on the relationship between their mechanical and antimicrobial performance. Finally, it ends with a discussion on the potential long-term impact of developing a truly multifunctional ultra-hard wearing bioactive DLC coating to extend the lifetime of total joint implants. [Display omitted] [ABSTRACT FROM AUTHOR]

Total hip replacement with metal-on-polymer hip prostheses is the most common treatment for late-stage osteoarthritis. However, the wear debris generated from the polymer acetabular liner remains a problem. Alternative materials with claimed superior wear properties have been proposed to overcome this problem. In this study, the wear behaviour of carbon fibre reinforced polyether ether ketone (CFR PEEK) was investigated under different contact stresses that are observed in the natural hip joint. A 50-station pin-on-disc machine (SuperCTPOD) was used to investigate the wear behaviour of 50 CFR PEEK pins articulated against cobalt chromium (CoCr) discs under five different contact stresses, namely 1.11, 1.38, 1.61, 2.00 and 5.30 MPa. The results showed that the wear rates of the pins did not differ significantly between groups under different contact stresses. In addition, CFR PEEK produced lower wear rates than ultrahigh molecular weight polyethylene and cross-linked polyethylene. However, the weight of the CoCr discs was found to decrease significantly at the end of the wear test, which was indicative of metallic wear. The findings of this study indicated that, despite having relatively low wear rates, CFR PEEK is not a good alternative to be utilised against orthopaedic metals. [ABSTRACT FROM AUTHOR]

Artificial finger joints lack the long-term clinical success seen with hip and knee prostheses. In part, this can be explained by the challenges of rheumatoid arthritis, a progressive disease which attacks surrounding tissues as well as the joint itself. Therefore, the natural finger joints' biomechanics are adversely affected, and consequently, this imbalance due to subluxing forces further challenges any prosthesis. Many different designs of finger prosthesis have been offered over a period of greater than 50 years. Most of these designs have failed, and it is likely that many of these failures could have been identified had the prostheses been appropriately tested prior to implantation into patients. While finger joint simulators have been designed, arguably only those from a single centre have been able to reproduce clinical-type failures of the finger prostheses tested in them. This article describes the design and development of a finger simulator at Durham University, UK. It explains and justifies the engineering decisions made and thus the evolution of the finger simulator. In vitro results and their linkage to clinical-type failures are outlined to help to show the effectiveness of the simulator. Failures of finger implants in vivo continue to occur, and the need for appropriate in vitro testing of finger prostheses remains strong. [ABSTRACT FROM AUTHOR]

This work aimed to engineer a multi-station shoulder simulator in order to wear test shoulder prostheses using recognized shoulder activities of daily living. A bespoke simulator was designed, built and subject to commissioning trials before a first wear test was conducted. Five JRI Orthopaedics Reverse Shoulder VAIOS 42 mm prostheses were tested for 2.0 million cycles and a mean wear rate and standard deviation of 14.2 ± 2.1 mm(3)/10(6) cycles measured for the polymeric glenoid components. This result when adjusted for prostheses diameters and test conditions showed excellent agreement with results from hip simulator studies of similar materials in a lubricant of bovine serum. The Newcastle Shoulder Simulator is the first multi-station shoulder simulator capable of applying physiological motion and loading for typical activities of daily living. [ABSTRACT FROM AUTHOR]

Using a 50-station pin-on-disc (SuperCTPOD) machine, the influence of lubricant viscosity on the wear of vitamin E blended crosslinked polyethylene was investigated. Five different test lubricants were prepared by mixing different concentrations of carboxymethyl cellulose powder with deionised water. The viscosity range of the lubricants was 0.002–0.155 Pa, a range that represents the viscosities of diseased and healthy synovial fluids. Five groups of pins (10 pins in each group) were articulated against cobalt chromium discs. Wear was measured in terms of weight loss from each pin and disc for every group. Every 500,000 cycles the experiment was stopped to take gravimetric measurements along with roughness measurements of the articulating surfaces. The test discs did not show a significant change in weight after 2.5 million cycles of testing (p > 0.05). For the pins, the group tested with the lowest viscosity (0.002 Pa) produced the highest wear rate, namely 0.931 mg/million cycles, and the wear rates of the other groups were 0.074, 0.027, 0.034 and 0.021 mg/million cycles respectively. The wear rates calculated for the five groups were all lower than the wear rates recorded for ultrahigh molecular weight polyethylene and not significantly different to crosslinked polyethylene. In addition, apart from group 1 pins (tested with the lowest lubricant viscosity (0.002 Pa)), the machining marks on the other pins were still present after 2.5 million cycles of testing, indicating low wear. [ABSTRACT FROM AUTHOR]

Explant analysis can provide key insights to understanding failures of artificial joints and thus how they might be improved for the ultimate benefit of patients. There are no previous reports of explant analysis of an artificial wrist joint. In this study, an explanted metal-on-polymer Maestro wrist was analysed both in macro and nanoscales to estimate its biotribological performance. The articulation was formed between a cobalt chromium carpal head and an ultrahigh molecular weight polyethylene bearing. The surface roughness values of its articulating surfaces and the backside of the articulation were measured. On average, the articulating surface roughness values were calculated as 0.06 ± 0.02 μm and 1.29 ± 0.63 μm for the cobalt chromium carpal head and ultrahigh molecular weight polyethylene bearing, respectively. Both surfaces had negative skewness, indicating a preponderance of valleys. On the articulating surface of the carpal head, light scratches were observed, and no impingement was observed throughout the component. The polymeric surface had a polished appearance. It had unidirectional scratches at the centre of the articulation, pits of different sizes on its articulating surface, and matt white subsurface regions. The backside of the UHMWPE bearing and the convex surface of the radial body that it was sitting on, were found to have average surface roughness values of 4.23 ± 0.69 μm and 5.57 ± 1.05 μm, respectively. The difference in the means was not significant (p > 0.05). Taking the articulating surface roughness values, the lubrication regime that the explanted Maestro wrist operated under in vivo was estimated for varying physiological conditions, i.e. varying loads, entraining velocities and lubricant viscosities. In every case considered, the explant was found to operate under boundary lubrication. [ABSTRACT FROM AUTHOR]

It has been proposed that an increased surface roughness of the femoral components of Total Knee Replacements (TKRs) may be a contributing factor to the accelerated wear of the polyethylene (PE) bearing and ultimately prosthesis failure. Oxidised Zirconium was introduced to the orthopaedic market in an attempt to reduce PE wear associated failures and increase the longevity of the prosthesis. In this study, non-contacting profilometry was used to measure the surface roughness of the femoral components of 6 retrieved TKRs (3 Oxidised Zirconium (OxZr) and 3 Cobalt Chromium alloy (CoCr) femoral components) and 2 as-manufactured femoral components (1 OxZr and 1 CoCr). A semi-quantitative method was used to analyse the damage on the retrieved PE components. The S a values for the retrieved OxZr femoral components ( S a = 0.093 µm ± 0.014) and for the retrieved CoCr femoral components ( S a = 0.065 µm ± 0.005) were significantly greater ( p < .05) than the roughness values for the as-manufactured femoral components (OxZr S a = 0.061 µm ± 0.004 and CoCr S a = 0.042 µm ± 0.003). No significant difference was seen between the surface roughness parameters of the retrieved OxZr and retrieved CoCr femoral components. There was no difference between the PE component damage scores for the retrieved OxZr TKRs compared to the retrieved CoCr TKRs. These results agree with other studies that both OxZr and CoCr femoral components roughen during time in vivo but the lack of difference between the surface roughness measurements of the two materials is in contrast to previous topographical reports. Further analysis of retrieved OxZr TKRs is recommended so that a fuller appreciation of their benefits and limitations be obtained. [ABSTRACT FROM AUTHOR]