Search

In this work, we propose and demonstrate an integrated dual linearly polarized cavity-backed patch antenna, which is excited by a concurrent dual-mode substrate integrated waveguide (SIW) structure. For the first time, we have exploited the TE10 and TE20 modes of a traveling wave in a dual-mode SIW configuration to excite the horizontal and vertical polarizations of the patch antenna. The proposed methodology yields a low-profile structure with a high interport isolation thanks to the inherent symmetry of the structure. Measurement results indicate an isolation performing better than 42 dB over a 600 MHz impedance bandwidth of the antenna. Moreover, a methodology is developed to implement transitions from the dual-mode SIW to the two different TEM transmission lines for separate but concurrent excitations of the device. Detailed field and impedance analyses are presented to explain the operation principle of the proposed antenna, which are supported by an excellent agreement between the obtained measurement and simulation results. [ABSTRACT FROM AUTHOR]

This article proposes and presents a fully planar endfire circularly polarized (CP) antenna with mingled three-layer substrates. It consists of a unidirectional dielectric radiator (UDR) and an antipodal linearly tapered slot antenna (ALTSA) surrounded by a UDR. The ALTSA is fed by a substrate integrated waveguide (SIW) on a thin substrate of $0.05\lambda _{0}$ , which can easily be integrated with RF subsystems. The UDR is fed by the ALTSA, which enables the UDR to enhance the original vertically polarized radiation rather than the horizontally polarized radiation from the ALTSA. Due to the polarization selectivity enhancement, an endfire CP antenna with a very thin substrate is created. An experimental prototype of the proposed antenna has been studied, designed, and measured. The measured impedance bandwidth of −10 dB covers a broadband of 29.7 GHz from 26.1 to 55.8 GHz, and the 3 dB AR bandwidth is 19.7 GHz ranging from 25.3 to 45 GHz. The measured gain is over 9 dBic from 27.8 GHz to over 32 GHz. A good performance with a small size of only $2.57\lambda _{0} \times 0.78\lambda _{0} \times 0.33\lambda _{0}$ , including the CPW-SIW transition, makes it an attractive option in the development of high gain planar endfire CP antennas and arrays for 5G and B5G applications. [ABSTRACT FROM AUTHOR]

A generalized mesh-network equivalent model for a microstrip rectangular patch antenna (RPA), which is simple yet efficient is proposed, studied, and demonstrated in this article. The mesh-network equivalent model is established through the segmentation of RPA width and radiation parameters into $M$ sections, as well as the segmentation of RPA length into $N$ sections. A general design procedure to realize the mesh-network equivalent model is addressed and described for any number of RPA segmentations, as desired by specific applications. Subsequently, the proposed mesh-network equivalent model is used to accurately evaluate the input impedance responses at various feed positions along the length of RPA. In addition, to include the effects of a slot etched inside the RPA geometry, a generalized microstrip coupled line equivalent model is proposed, analyzed, and discussed in detail. Eventually, the microstrip coupled line model in conjunction with the proposed mesh-network equivalent model can accurately estimate the input impedance response of a slotted RPA, and has been verified for RPA with center slot, edge slot, and multiple slots as examples in this work. Two cases with multiport excitation of RPA are also analyzed and presented as a part of this work. For demonstration purposes, all these prototypes are designed, fabricated, and measured at 28 GHz. The proposed equivalent model-based results are validated by measured and simulated counterparts. Furthermore, the extension of the proposed mesh-network model to accommodate slots of smaller size inside RPA, RPA loaded with via, inverted-F antenna, and multimode operation are demonstrated and discussed through a comparison between mesh-network modeling results and simulation results. [ABSTRACT FROM AUTHOR]

Substrate integrated waveguide (SIW) cavity backed dual-band triangular-ring slot (TRS) antennas are proposed for planar integration. First, a low profile dual band 45^\circ linearly polarized (LP) antenna is designed and analyzed. The dual-mode TRS is proposed and developed by simultaneously exciting the mode of the slot and the mode of the patch inside the slot. To minimize the antenna size, the lowest mode (TE110 mode) of the SIW cavity is adopted to excite the TRS. The -10 dB impedance bandwidth at the higher band is 5.9%, 58.3% wider than that of the conventional SIW cavity backed slot antenna. The interactions of the SIW cavity, the slot mode and the patch mode are analyzed with circuit models and verified by full wave simulations, which provides a new insight into the SIW cavity backed antennas. Then, by exciting a pair of the 45^\circ LP antennas with an SIW coupler, a circularly polarized (CP) dual band antenna with a small frequency ratio of 1.26 is developed. The two antennas are fabricated and tested, and the measured and simulated results agree well. [ABSTRACT FROM PUBLISHER]

In this article, an effective design method is presented to design a miniaturized UWB antenna with four band-notches. By carefully integrating C-shaped slots, L-shaped open circuit stub, and T-shaped parasitic strip onto the primitive miniaturized antenna, four band-notches (VSWR > 2) could be achieved at 3.38-3.65 GHz, 4.95-6.05 GHz, 7.42-7.78 GHz, and 8.1-8.9 GHz to reject WiMAX, WLAN, X-band satellite communication, and ITU 8 GHz band signals. Simulated and measured results show that this antenna could operate from 3.15-11.1 GHz (VSWR < 2), and maintain omnidirectional directivity patterns at H-plane. Moreover, the proposed antenna has a very compact size of 18.6 × 22 × 1.5 mm3. © 2013 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:1202-1206, 2013; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27546 [ABSTRACT FROM AUTHOR]

A class of three-dimensional planar arrays in substrate integrated waveguide (SIW) technology is proposed, designed and demonstrated with 8 \times 16 elements at 35 GHz for millimeter-wave imaging radar system applications. Endfire element is generally chosen to ensure initial high gain and broadband characteristics for the array. Fermi-TSA (tapered slot antenna) structure is used as element to reduce the beamwidth. Corrugation is introduced to reduce the resulting antenna physical width without degradation of performance. The achieved measured gain in our demonstration is about 18.4 dBi. A taper shaped air gap in the center is created to reduce the coupling between two adjacent elements. An SIW H-to-E-plane vertical interconnect is proposed in this three-dimensional architecture and optimized to connect eight 1 \times 16 planar array sheets to the 1 \times 8 final network. The overall architecture is exclusively fabricated by the conventional PCB process. Thus, the developed SIW feeder leads to a significant reduction in both weight and cost, compared to the metallic waveguide-based counterpart. A complete antenna structure is designed and fabricated. The planar array ensures a gain of 27 dBi with low SLL of 26 dB and beamwidth as narrow as 5.15 degrees in the E-plane and 6.20 degrees in the 45^\circ-plane. [ABSTRACT FROM PUBLISHER]