Search

Research on the Alcator C-Mod tokamak [1] is focused on high particle- and power-density plasma regimes to understand particle and energy transport in the core, the dynamics of the H-mode pedestal, and scrape-off layer and divertor physics. The auxiliary heating is provided exclusively by RF waves, and both the physics and technology of RF heating and current drive are studied. The momentum which is manifested in strong toroidal rotation, in the absence of direct momentum input, has been shown to be transported in from the edge of the plasma following the L–H transition, with timescale comparable to that for energy transport. In discharges which develop internal transport barriers, the rotation slows first inside the barrier region, and then subsequently outside of the barrier foot. Heat pulse propagation studies using sawteeth indicate a very narrow region of strongly reduced energy transport, located near r/a = 0.5. Addition of on-axis ICRF heating arrests the buildup of density and impurities, leading to quasi-steady conditions. The quasi-coherent mode associated with enhanced D-Alpha (EDA) H-mode appears to be due to a resistive ballooning instability. As the pedestal pressure gradient and temperature are increased in EDA H-mode, small ELMs appear; detailed modelling indicates that these are due to intermediate n peeling–ballooning modes. Phase contrast imaging has been used to directly detect density fluctuations driven by ICRF waves in the core of the plasma, and mode conversion to an intermediate wavelength ion cyclotron wave has been observed for the first time. The bursty turbulent density fluctuations, observed to drive rapid cross-field particle transport in the edge plasma, appear to play a key role in the dynamics of the density limit. Preparations for quasi-steady-state advanced tokamak studies with lower hybrid current drive are well underway, and time dependent modelling indicates that regimes with high bootstrap fraction can be produced.

The effect of divertor baffling on impurity neutral and impurity ion compression in ohmic discharges in the Alcator C-Mod tokamak is explored. Experiments are performed using a novel divertor bypass which allows in situ variations to the divertor baffling. The results indicate that divertor baffling in Alcator C-Mod plays an important role in impurity neutral compression, but little role in impurity ion compression. The apparent separation between neutral compression and ion compression is surprising, but is consistent with a model in which the neutral compression (both in deuterium and argon) is determined by a leakage flux through the baffle structure from the divertor region to the main chamber which is independent of the leakage conductance. Instead, the leakage fluxes appear to be determined by the divertor plasma conditions (including impurity and fuel ions), which are not influenced by the baffle structure.

The formation of internal transport barriers (ITBs) has been observed in the core region of Alcator C-Mod [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] under a variety of conditions. The improvement in core confinement following pellet injection (pellet enhanced performance or PEP mode) has been well documented on Alcator C-Mod in the past. Recently three new ITB phenomena have been observed which require no externally applied particle or momentum input. Short lived ITBs form spontaneously following the high confinement to low confinement mode transition and are characterized by a large increase in the global neutron production (enhanced neutron or EN modes). Experiments with ion cyclotron range of frequencies power injection to the plasma off-axis on the high field side results in the central density rising abruptly and becoming peaked. The ITB formed at this time lasts for ten energy confinement times. The central toroidal rotation velocity decreases and changes sign as the density rises. Simi...

Co-current central impurity toroidal rotation has been observed in Alcator C-Mod plasmas with on-axis ICRF heating. The rotation velocity increases with plasma stored energy and decreases with plasma current. Very similar behaviour has been seen during ohmic H modes, which suggests that the rotation, generated in the absence of an external momentum source, is not mainly an ICRF effect. A scan of ICRF resonance location across the plasma has been performed in order to investigate possible influences on the toroidal rotation. With a slight reduction of toroidal magnetic field from 4.7 to 4.5 T and a corresponding shift of the ICRF resonance from r/a = -0.36 to -0.48, the central toroidal rotation significantly decreased together with the formation of an internal transport barrier (ITB). During the ITB phase, electrons and impurities peaked continuously for |r/a| ≤ 0.5. Comparison of the observed rotation and neoclassical predictions indicates that the core radial electric field changes from positive to negative during the ITB phase. Similar rotation suppression and ITB formation have been observed during some ohmic H mode discharges.

Detailed measurements of the magnitude and location of volumetric recombination occurring in the detached divertor of Alcator C-Mod tokamak [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] are presented. The drop in divertor plate ion current during detachment is due to two mechanisms: (1) volumetric recombination in the divertor plasma; and (2) reductions in the divertor ion source. Depending on plasma conditions, each of these can be the primary mechanism for the observed ion current reduction in detachment. The ion source during detachment is inferred and its magnitude is consistent with the measured divertor power flow. A scaling of the density in the divertor recombining region for L- (low confinement) mode plasmas is found, ne,r∝ne0.8⋅PSOL2/7. A model based on pressure variation along a flux surface during detachment is consistent with the main features of this scaling.

Recent breakthroughs in silicon detector technology now permit measurement of radiated power over a wide range in photon energies. These detectors (also known as AXUV photodiodes) have a flat spectral power response from ultraviolet to x-ray energies, and with a slightly reduced efficiency all the way down to visible wavelengths. Since they can be made small, multichannel detectors allow high spatial resolution to be combined with an intrinsic high temporal resolution, which can reach the microsecond range, depending on the application. Additional features include ease of use and installation, and relatively low cost compared to other techniques. A combination of two multichannel toroidally viewing systems has been recently installed on the Alcator C-Mod tokamak. The first array, which is composed of 16 channels, sees tangentially the outer-half of the plasma at the midplane, and is used to measure the total power radiated. The second array, also located at the midplane, consists of 19 channels and views ...

The intrinsic impurity content of molybdenum and carbon was measured in the Alcator C-Mod tokamak using low resolution, multilayer mirror (MLM) spectroscopy ( Delta lambda ~1-10 AA). Molybdenum was the dominant high-Z impurity and originated from the molybdenum armour tiles covering all of the plasma facing surfaces (including the inner column, the poloidal divertor plates and the ion cyclotron resonant frequency (ICRF) limiter) at Alcator C-Mod. Despite the all metal first wall, a carbon concentration of 1 to 2% existed in the plasma and was the major low-Z impurity in Alcator C-Mod. Thus, the behaviour of intrinsic molybdenum and carbon penetrating into the main plasma and the effect on the plasma must be measured and characterized during various modes of Alcator C-Mod operation. To this end, soft X-ray extreme ultraviolet (XUV) emission lines of charge states, ranging from hydrogen-like to helium-like lines of carbon (radius/minor radius, r/a~1) at the plasma edge to potassium to chlorine-like (0.4

A series of experiments, examining the confinement properties of ion cyclotron range of frequencies (ICRF) heated H mode plasmas, has been carried out on the Alcator C-Mod tokamak. Alcator C-Mod is a compact tokamak that operates at high particle, power and current densities at toroidal fields up to 8 T. Under these conditions the plasma is essentially thermal with very little contribution to the stored energy from energetic ions (typically no more than 5%) and with Ti~Te. Most of the data were taken with the machine in a single null `closed' divertor configuration with the plasma facing components clad in molybdenum tiles. The data include those taken both before and after the first wall surfaces were coated with boron, with emphasis on the latter. H modes obtained from plasmas run on boronized walls typically had a lower impurity content and radiated power and attained a higher stored energy than those run on bare molybdenum. Confinement enhancement, the energy confinement time normalized to L mode scaling, for discharges with boronized walls, ranged from 1.6 to 2.4. The unique operating regime of the Alcator C-Mod device provided a means for extending the tests of global scaling laws to parameter ranges not previously accessible. For example, the Alcator C-Mod edge localized mode (ELM)-free data were found to be 1.1 to 1.6 times the ITERH93 scaling and the ELMy data almost 2.0 to 2.8 times the ITERH92 ELMy scaling law, suggesting that the size scaling in both scalings may be too strong. While both ELM-free and ELMy discharges were produced, the ELM characteristics were not easily compared with observations on other devices. No large, low frequency ELMs were seen despite the very high edge pressure and temperature gradients that were attained. For all of our H mode discharges, a clear linear relationship between the edge temperature pedestal and the temperature gradient in the core plasma was observed; the discharges with the `best' transport barriers also showing the greatest improvement in core c

Trace non-recycling impurities have been injected into Alcator C-Mod [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] plasmas in order to determine impurity transport coefficients. Subsequent impurity emission has been observed with spatially scanning x-ray and Vacuum Ultra-Violet (VUV) spectrometer systems. Measured time-resolved brightness profiles of helium- and lithium-like transitions have been compared with those calculated from a transport code which includes impurity diffusion and convection in conjunction with an atomic physics package for individual line emission. During Low-Confinement-Mode (L-mode) plasmas, the transport can be characterized by pure diffusion, with coefficients ∼5000 cm2/s, reflecting the ∼20 ms decay in the x-ray and VUV line brightnesses. During High-Confinement-Modes (H-modes), the impurity confinement times are much longer, and the modelling requires that there be a strong inward convection (of order 1000 cm/s) near the plasma edge, with greatly reduced diffusion (o...

A series of experiments has been carried out to determine the relative screening of the low recycling gaseous impurities, nitrogen and methane, in Alcator C-Mod tokamak [Phys. Plasmas 1, 1511 (1994)] discharges. The impurity density in the core plasma is directly proportional to the rate of impurity injection. Screening was found to vary weakly with plasma density but to be markedly dependent on the poloidal position of injection. Detachment of the plasma results in significantly less screening both in Ohmic and in high confinement (H-mode) discharges, particularly when the gas is injected into the divertor or at the inner vessel wall. Evidence of impurity transport from the scrape-off layer into the divertor using bolometry and visible spectroscopy is presented and modeling of the transport using a two-dimensional Monte Carlo code is described.

Highly localized direct electron heating [full width at half-maximum (FWHM)≅0.2a] via mode converted ion Bernstein waves has been observed in the Alcator C-Mod Tokamak [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)]. Electron heating at or near the plasma center (r/a⩾0.3) has been observed in H(3He) discharges at B0=(6.0–6.5) T and ne(0)≅1.8×1020 m−3. [Here, the minority ion species is indicated parenthetically.] Off-axis heating (r/a⩾0.5) has also been observed in D(3He) plasmas at B0=7.9 T. The concentration of 3He in these experiments was in the range of n3He/ne≅(0.2–0.3) and the locations of the mode conversion layer and electron heating peak could be controlled by changing the 3He concentration or toroidal magnetic field (B0). The electron heating profiles were deduced using a rf modulation technique. Detailed comparisons with one-dimensional and toroidal full-wave models in the ion cyclotron range of frequencies have been carried out. One-dimensional full-wave code predictions were found to ...

Enhanced confinement modes up to a toroidal field of BT=8 T have been studied with up to 3.5 MW of radiofrequency (rf) heating power in the ion cyclotron range of frequencies (ICRF) at 80 MHz. H-mode is observed when the edge temperature exceeds a threshold value. The high confinement mode (H-mode) with higher confinement enhancement factors (H) and longer duration became possible after boronization by reducing the radiated power from the main plasma. A quasi-steady state with high confinement (H=2.0), high normalized beta (βN=1.5), low radiated power fraction (Pradmain/Ploss=0.3), and low effective charge (Zeff=1.5) has been obtained in Enhanced Dα H-mode. This type of H-mode has enhanced levels of continuous Dα emission and very little or no edge localized mode (ELM) activity, and reduced core particle confinement time relative to ELM-free H-mode. The pellet enhanced performance (PEP) mode is obtained by combining core fueling with pellet injection and core heating. A highly peaked pressure profile with a central value of 8 atmospheres was observed. The steep pressure gradient drives off-axis bootstrap current, resulting in a shear reversed safety factor (q) profile. Suppression of sawteeth appears to be important in maintaining the highly peaked pressure profile. Lithium pellets were found to be more effective than deuterium pellets in raising q0.

Local measurements of line emission of either intrinsic or gas puffed impurities will be performed around and below the X point. Such spectroscopic measurements, together with divertor Thomson scattering and bolometric imaging will enable estimates of divertor impurity particle distributions and power losses. A proposed multilayer mirror (MLM) diagnostic mounted inside the tokamak vessel will measure XUV (100–200 A) emission from impurities at multiple locations in the divertor region of the C-Mod tokamak. A prototype of this instrument measuring N V at 162.6 A is scheduled to be installed on C-Mod with a single chordal view of the X point. A multichordal/multispectral device using MLMs and gratings has been designed for the DIII-D tokamak. The instrument will measure the resonance emission of C II to C VI from 40–2000 A, thus enabling a more direct and reliable estimate of the impurity content in the divertor. At DIII-D, the device will be mounted on a port below the mid plane avoiding spectroscopic cont...

Results of ICRF heating experiments in Alcator C-Mod during the November 1994 to June 1995 campaign are summarized. Efficient heating of high-density plasmas was demonstrated with high power densities (up to volume averaged, surface averaged). These experiments were carried out with RF powers up to 3.5 MW at 80 MHz, at magnetic fields up to 8 T and plasma currents up to 1.2 MA. For on-axis hydrogen minority heating at 5.3 T, near complete absorption is achieved. Energy confinement in L-mode plasmas was found to be consistent with the ITER89-P scaling. H-mode is routinely observed when the ion drift is directed toward the X-point. The H-mode power threshold was found to scale as low as , which is a factor of two lower than the scaling observed on other tokamaks. PEP modes with highly peaked density and ion temperature profiles and highly enhanced fusion reactivity were obtained with Li pellet injection followed by on-axis ICRF heating at both (H minority heating) and 8 T ( minority heating). In H - plasmas at T highly localized direct electron heating by the mode converted ion Bernstein wave was observed. Nearly complete absorption by electrons in a small volume resulted in an extremely high electron heating power density of with .

The sign of the toroidal magnetic field has a major effect on the divertor in Alcator C-Mod, determining whether the higher recycling is on the inboard or outboard side and leading to inboard/outboard temperature and density differences of up to a factor of ten. A recently published paper (Hutchinson et al 1995 Plasma Phys. Control. Fusion 37 1389) reported in detail on these observations, which are an indication of the importance of plasma particle drifts for understanding and modelling the divertor. The conference presentation covered these published results and also some additional results, documented here, in which the plasma flows associated with the field-direction-dependent asymmetries are measured using a Mach probe and a localized impurity puffing plume analysis technique.

The divertor of the Alcator C‐Mod tokamak [Phys. Plasmas 1, 1511 (1994)] routinely radiates a large fraction of the power entering the scrape‐off layer. This dissipative divertor operation occurs whether the divertor is detached or not, and large volumetric radiative emissivities, up to 60 MW m−3 in ion cyclotron range of frequency (ICRF) heated discharges, have been measured using bolometer arrays. An analysis of both Ohmic and ICRF‐heated discharges has demonstrated some of the relative merits of detached divertor operation versus high‐recycling divertor operation. An advantage of detached divertor operation is that the power flux to the divertor plates is decreased even further than its already low value. Some disadvantages are that volumetric losses outside the separatrix in the divertor region are decreased, the neutral compression ratio is decreased, and the penetration efficiency of impurities increases.

The regime of high particle and energy confinement known as the H mode [Phys. Rev. Lett. 49, 1408 (1982)] has been extended to a unique range of operation for divertor tokamaks up to toroidal fields of nearly 8 T, line‐averaged electron densities of 3×1020 m−3, and surface power densities of nearly 0.6 MW/m2 in the compact high‐field tokamak Alcator C Mod [Phys. Plasmas 1, 1511 (1994)]. H modes are achieved in Alcator C Mod with Ion Cyclotron Resonant Frequency (ICRF) heating and with Ohmic heating alone without boronization of the all molybdenum tiled first wall. Large increases in charge exchange flux are observed during the H mode over the entire range of energies from 2 to 10 keV. There appears to be an upper limit to the midplane neutral pressure, of about 0.08 Pa above which no H modes have been observed. The plasmas with the best energy confinement have the lowest midplane neutral pressures, below 0.01 Pa. There is an edge electron temperature threshold such that Te≥280 eV ±40 eV for sustaining the...

Imbalances between the inboard and outboard legs of the single null divertor in tokamak Alcator C-Mod are observed to reverse when the direction of the toroidal field is reversed. These imbalances are measured by embedded probes in the target plates, tomographic reconstructions of bolometry and line radiation, and visible imaging. Density imbalances of about a factor of ten at the targets are observed at moderate density, decreasing as the density is raised until they are almost balanced. The data indicate that the electron pressure is not imbalanced, thus arguing against momentum imbalance as the cause of these drift-induced effects. Instead, power flux imbalance caused by Er V-product B convection, and enhanced by radiation, is suggested as the underlying cause.

A series of transport experiments has been carried out in Alcator‐C‐Mod. [Phys Plasmas 1, 1511 (1994)]. Data from both Ohmic and ICRF (ion cyclotron range of frequencies) heated plasmas can be fitted with an L‐mode (low mode) scaling law. The Ohmic τE’s show no scaling with density in any regime and can reach values of 2–3 times neo‐Alcator. Impurity confinement has been studied with the laser blow‐off technique with τI showing nearly linear scaling with plasma current. Ohmic and ICRF H modes are obtained over a wide range of discharge parameters, extending the range in the international database for nB, by almost a factor of 10. The power threshold for ELM‐free (edge localized mode) discharges is in rough agreement with the scaling P/S=0.044nB. Energy diffusivities of Ohmic and ICRF heated plasmas have been measured from local analysis of plasma profiles and power fluxes. The same analysis produces a value for plasma resistivity which lies between the Spitzer and neoclassical calculations. Analysis of pl...

Detailed measurements and transport analysis of divertor conditions in Alcator C‐Mod [Phys. Plasmas 1, 1511 (1994)] are presented for a range of line‐averaged densities, 0.7

Early results from the Alcator C-Mod tokamak indicate that ohmic energy confinement does not obey the Neo-Alcator scaling. Instead 'Ohmic L-mode' confinement, close to ITER89-P, is obtained, which substantially exceeds Neo-Alcator under some circumstances. ICRF-heated plasmas follow the same scaling. H-modes are observed both in ohmic and ICRF heated plasmas, with confinement enhancements of about 2 for ELM-free conditions. Divertor operation into the closed chamber shows different regimes, depending on the density. Of particular interest is the progressive detachment at moderate to high densities. Power to the divertor plates is generally low, reflecting the influence of strong radiation in the divertor. The scaling of parameters from Alcator's growing edge database is briefly summarized.

Ohmic H modes have been achieved in ALCATOR C-MOD with toroidal fields up to BT ≈ 5.25 T and line averaged densities up to ne ≈ 1.4 × 1020 m-3 with less than 1 MW of input power. In ELM-free cases at lower toroidal fields, the energy confinement increases by at least 60% and the particle confinement increases by more than a factor of two. The ELM-free H modes appear to fit the threshold power scaling observed on other tokamaks, P/S (MW/m2)=4.4 × 10-3 neBT (1019 m-3.T), up to power densities of about 0.15 MW/m2. At higher toroidal fields, ELMy H modes were observed after the injection of lithium pellets at about half of the scaled threshold power density. All of these results were obtained with molybdenum plasma facing components and the ELM-free H modes were obtained without boronization or other wall coatings

A 4‐strap ICRF antenna was designed and fabricated for plasma heating and current drive in the Alcator C‐Mod tokamak. Initial upgrades were carried out in 2000 and 2001, which eliminated surface arcing between the metallic protection tiles and reduced plasma‐wall interactions at the antenna front surface. A boron nitride septum was added at the antenna midplane to intersect electric fields resulting from rf sheath rectification, which eliminated antenna corner heating at high power levels. The current feeds to the radiating straps were reoriented from an E∥B to E⊥B geometry, avoiding the empirically observed ∼15 kV/cm field limit and raising antenna voltage holding capability. Further modifications were carried out in 2002 and 2003. These included changes to the antenna current strap, the boron nitride tile mounting geometry, and shielding the BN‐metal interface from the plasma. The antenna heating efficiency, power and voltage characteristics under these various configurations will be presented.

The object of this review is to summarize the achievements of research on the Alcator C-Mod tokamak [Hutchinson et al., Phys. Plasmas 1, 1511 (1994) and Marmar, Fusion Sci. Technol. 51, 261 (2007)] and to place that research in the context of the quest for practical fusion energy. C-Mod is a compact, high-field tokamak, whose unique design and operating parameters have produced a wealth of new and important results since it began operation in 1993, contributing data that extends tests of critical physical models into new parameter ranges and into new regimes. Using only high-power radio frequency (RF) waves for heating and current drive with innovative launching structures, C-Mod operates routinely at reactor level power densities and achieves plasma pressures higher than any other toroidal confinement device. C-Mod spearheaded the development of the vertical-target divertor and has always operated with high-Z metal plasma facing components—approaches subsequently adopted for ITER. C-Mod has made ground-breaking discoveries in divertor physics and plasma-material interactions at reactor-like power and particle fluxes and elucidated the critical role of cross-field transport in divertor operation, edge flows and the tokamak density limit. C-Mod developed the I-mode and the Enhanced Dα H-mode regimes, which have high performance without large edge localized modes and with pedestal transport self-regulated by short-wavelength electromagnetic waves. C-Mod has carried out pioneering studies of intrinsic rotation and demonstrated that self-generated flow shear can be strong enough in some cases to significantly modify transport. C-Mod made the first quantitative link between the pedestal temperature and the H-mode's performance, showing that the observed self-similar temperature profiles were consistent with critical-gradient-length theories and followed up with quantitative tests of nonlinear gyrokinetic models. RF research highlights include direct experimental observation of ion cyclotron range of frequency (ICRF) mode-conversion, ICRF flow drive, demonstration of lower-hybrid current drive at ITER-like densities and fields and, using a set of novel diagnostics, extensive validation of advanced RF codes. Disruption studies on C-Mod provided the first observation of non-axisymmetric halo currents and non-axisymmetric radiation in mitigated disruptions. A summary of important achievements and discoveries are included., United States. Dept. of Energy (Cooperative Agreement DE-FC02-99ER54512), United States. Dept. of Energy (Cooperative Agreement DE-FG03-94ER-54241), United States. Dept. of Energy (Cooperative Agreement DE-AC02-78ET- 51013), United States. Dept. of Energy (Cooperative Agreement DE-AC02-09CH11466), United States. Dept. of Energy (Cooperative Agreement DE-FG02-95ER54309), United States. Dept. of Energy (Cooperative Agreement DE-AC02-05CH11231), United States. Dept. of Energy (Cooperative Agreement DE-AC52-07NA27344), United States. Dept. of Energy (Cooperative Agreement DE-FG02- 97ER54392), United States. Dept. of Energy (Cooperative Agreement DE-SC00-02060)

An internal transport barrier (ITB) mode has been produced in the Alcator C-Mod tokamak via the application of 1–2 MW of off-axis ICRF heating power at 4.5 T and 80 MHz. This mode is characterized by strong peaking of the electron density profile with ne(0) increasing to 6–8×1020 m−3 while the plasma remains H-mode like outside the barrier foot (r/a≃0.5) with ne≃1.5−2.0×1020 m−3. Formation of the density barrier is typically accompanied by a decrease in the toroidal plasma rotation velocity from co-current to zero. Transport analysis of these discharges using the TRANSP code indicates the formation of a transport barrier in χeff(r) at r/a≲0.5. Heating and control of the transport barrier was successfully demonstrated by simultaneously injecting 0.6–1.0 MW of on-axis ICRF heating power at 70 MHz.

Internal transport barrier (ITB) modes have been observed with intense, off-axis ICRF heating in Alcator C-Mod. This barrier mode is routinely produced in enhanced Dα H-mode, 4.5 T, 0.8 MA discharges (H cyclotron position is r/a∼0.5 to the high field side). From TRANSP analysis, the χeff is significantly reduced inside r/a∼0.4 where the density peaking is observed. With the barrier formation, the toroidal plasma rotation near the axis reversed from co-current (+50 km/sec) to counter current direction (−20 km/sec). In an effort to maintain the barrier, experiments utilizing a third antenna, operated at 70 MHz, allowed central ICRF heating of the ITB mode. Initial experiments with up to 1.2 MW confirmed the energy transport barrier and allowed significant increase in the ion temperatures. With the central heating, the ITB was sustained and the density and impurity peaking were arrested. Furthermore, the central rotation was observed to rotate in the co-current direction with the central heating. We have als...

Routine high power operation of the ICRF heating system (up to 3.5 MW at 80 MHz) has enabled studies of enhanced confinement modes as well as high heat flux divertor experiments in the Alcator C-Mod tokamak with toroidal magnetic fields of up to 8 T. H-mode was routinely observed when the edge temperature exceeded a threshold value. Boronization has reduced the radiated power to approximately 30% of the input power, which had little effect on confinement of L-mode plasmas, but had a large impact on the performance of H-mode plasmas. It has become possible to achieve quasi-steady-state H-modes with H≃2 and βN≃1.5 simultaneously with Prad/Pin≃0.3 and Zeff≃1.5. PEP mode can be obtained with central ICRF heating combined with core fuelling by pellet injection. Because of the high central density, ion heating becomes the dominant heating channel during PEP mode. For direct electron heating schemes, such as heating by the mode converted ion Bernstein wave, the electron heating profile can be measured using the ...

ICRF heating experiments have been carried out in the Alcator C‐Mod tokamak at power levels up to 3.5 MW. Features of Alcator C‐Mod include high density operation, molybdenum plasma facing components, and a closed divertor configuration. The heating is accomplished with two two‐strap antennas each run with dipole phasing at 80 MHz in deuterium plasmas with a hydrogen minority resonant at 5.3 T. Plasmas with Ti=4 keV and Te=5 keV at ne=1×1020 m−3 have been produced with 3.5 MW of heating power. The heating has been shown to be strongest with a low minority concentration (1–5%) and the resonance on axis. For ne≳2×1020 m−3, the central Zeff remains below 1.5 with more than 2.5 MW of applied rf power. L‐mode confinement scaling is observed both for ohmic and ICRF‐heated plasmas with some deterioration at higher densities. H‐mode transitions have been produced with the threshold for ELM‐free H‐modes at or below the ASDEX/DIII‐D scaling. Enhanced confinement with strongly peaked density profiles has been achi...

Central toroidal rotation and impurity transport coefficients have been determined in Alcator C-Mod [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] Ohmic high confinement mode (H-mode) plasmas from observations of x-ray emission following impurity injection. Rotation velocities up to 3×104 m/sec in the co-current direction have been observed in the center of the best Ohmic H-mode plasmas. Purely ohmic H-mode plasmas display many characteristics similar to ion cyclotron range of frequencies (ICRF) heated H-mode plasmas, including the scaling of the rotation velocity with plasma parameters and the formation of edge pedestals in the electron density and temperature profiles. Very long impurity confinement times (∼1 sec) are seen in edge localized mode-free (ELM-free) Ohmic H-modes and the inward impurity convection velocity profile has been determined to be close to the calculated neoclassical profile.