Search

biBackground:/i/bIvermectin has received worldwide attention as a potential COVID-19 treatment after showing antiviral activity against SARS-CoV-2iin vitro./iHowever, the pharmacokinetic limitations associated with oral administration have been postulated as limiting factors to its bioavailability and efficacy. These limitations can be overcome by targeted delivery to the lungs. In this study, inhalable dry powders of ivermectin and lactose crystals were prepared and characterized for the potential treatment of COVID-19.biMethods:/i/bIvermectin was co-spray dried with lactose monohydrate crystals and conditioned by storage at two different relative humidity points (43% and 58% RH) for a week. Theiin vitro/idispersion performance of the stored powders was examined using a medium-high resistance Osmohaler connecting to a next-generation impactor at 60 L/min flow rate. The solid-state characteristics including particle size distribution and morphology, crystallinity, and moisture sorption profiles of raw and spray-dried ivermectin samples were assessed by laser diffraction, scanning electron microscopy, Raman spectroscopy, X-ray powder diffraction, thermogravimetric analysis, differential scanning calorimetry, and dynamic vapor sorption.biResults:/i/bAll the freshly spray-dried formulation (T0) and the conditioned samples could achieve the anticipated therapeutic dose with fine particle dose of 300 μg, FPFsubrecovered/subof 70%, and FPFsubemitted/subof 83%. In addition, the formulations showed a similar volume median diameter of 4.3 μm and span of 1.9. The spray-dried formulations were stable even after conditioning and exposing to different RH points as ivermectin remained amorphous with predominantly crystalline lactose.biConclusion:/i/bAn inhalable and stable dry powder of ivermectin and lactose crystals was successfully formulated. This powder inhaler ivermectin candidate therapy appears to be able to deliver doses that could be safe and effective to treat the SARS-COV-2 infection. Further development of this therapy is warranted.

In order to better understand powder dispersion in dry powder inhaler (DPI) devices, a new powder disperser was designed, which uses flow modifiers to alter powder fluidization behavior so as to physically replicate various flow conditions observed in a range of commercial DPIs. The influence of these modifiers on the performance of the DPI was analyzed for flowrates progressing from laminar (15 L/min) to transitional (30 L/min), and finally turbulent flow regimes (60 L/min) in the device. The aerosol performance of the disperser was measured using a Next Generation Impactor. For flowrate in the laminar regime, powder evacuation from the disperser was generally insufficient (85% when the device was operated in the turbulent flow regime. In contrast, the highest fine particle fraction (FPF) and lowest throat deposition were achieved when operating in the transitional flow regime. The FPF could be increased further by applying flow modifications such as narrowing the air passage before the powder pocket, inducing localized turbulence (by a grid) near the powder pocket, and by changing the loading position of the powder. Flow modifiers had the most noticeable effect under a laminar flow regime, however, the device operated most efficiently under a transitional flow regime.

The aim of this study was to investigate the ability of L-leucine (LL) in preventing moisture-induced deterioration in the in vitro aerosolization performance of spray-dried (SD) salbutamol sulfate (SS). Increasing mass fraction of LL (5-80%) were co-spray dried with SS, and the physicochemical properties of the powders were characterized by laser diffraction, X-ray powder diffraction (XRD) and dynamic vapour sorption (DVS). Furthermore, the surface morphology and chemistry of fine particles was analyzed by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The in vitro aerosolization performance of powders stored at different relative humidity (RH) was evaluated by a next generation impactor (NGI). The SD SS powders were moderately hygroscopic and amorphous, of which the uptake of moisture upon storage caused a drop in the aerosolization performance. The results showed that 40% (w/w) LL was sufficient to eliminate the effect of moisture on the aerosolization performance at 60% RH. The formulation containing 40% (w/w) LL also maximized the aerosolization performance of SD SS powders (stored in desiccator) with the emitted fraction being 90.0±1.8%, and the fine particle fraction based on the recovered dose (FPFrecovered) and emitted dose (FPFemitted) being 78.0±3.7% and 86.6±2.9%, respectively. The underlying mechanisms were that the crystalline LL increased the degree of particle surface corrugation, and reduced particle fusion and cohesiveness to facilitate dispersion. However, there is still a great challenge to prevent the moisture-induced deterioration in the aerosolization performance at 75% RH due to the recrystallization of SD SS. In conclusion, LL is a potential excipient for reducing moisture-induced deterioration in the aerosolization performance of SD amorphous powders, but still has drawbacks in preventing the recrystallization-induced deterioration.

Background: Aerosol delivery through a nasal high flow (NHF) system is attractive for clinicians as it allows for simultaneous administration of oxygen and inhalable drugs. However, delivering a fine particle fraction (FPF, particle wt. fraction < 5.0 μm) of drugs into the lungs has been very challenging, with highest value of only 8%. Here, we aim to develop an efficient nose-to-lung delivery system capable of delivering improved quantities (FPF > 16%) of dry powder aerosols to the lungs via an NHF system. Methods: We evaluated the FPF of spray-dried mannitol with leucine with a next generation impactor connected to a nasopharyngeal outlet of an adult nasal airway replica. In addition, we investigated the influence of different dispersion (20-30 L/min) and inspiratory (20-40 L/min) flow rates, on FPF. Results: We found an FPF of 32% with dispersion flow rate at 25 L/min and inspiratory flow rate at 40 L/min. The lowest FPF (21%) obtained was at the dispersion flow rate at 30 L/min and inspiratory flow rate at 30 L/min. A higher inspiratory flow rate was generally associated with a higher FPF. The nasal cannula accounted for most loss of aerosols. Conclusions: In conclusion, delivering a third of inhalable powder to the lungs is possible in vitro through an NHF system using a low dispersion airflow and a highly dispersible powder. Our results may lay the foundation for clinical evaluation of powder aerosol delivery to the lungs during NHF therapy in humans.

Knowledge that enables the accurate simulation of drug deposition in the human upper airway is necessary to develop robust platforms for efficient drug delivery by inhalation devices. The human upper airway is deformable during inhalation but how it could affect the deposition of inhaled drugs is unknown. We aimed to determine whether pharyngeal deformation at the soft palate level would have any significant effects on throat deposition, in vitro lung dose and fine particle fraction. In this study, dry mannitol powders were delivered to the next-generation cascade impactor (NGI) through the United States Pharmacopeia (USP) throat, and a realistic upper airway cast (RUPAC) at flow rates of 40, 60 and 80 L min−1. Deformation of the upper airway at 25%, 50%, and 75% in the lateral and antero-posterior directions were experimentally simulated in the RUPAC. Throat deposition (p = 0.04) is significantly affected when the upper airway deforms laterally but not antero-posteriorly.

L-Leucine (LL) has been widely used to enhance the dispersion performance of powders for inhalation. LL can also protect powders against moisture, but this effect is much less studied. The aim of this study was to investigate whether LL could prevent moisture-induced deterioration in in vitro aerosolization performances of highly hygroscopic spray-dried powders. Disodium cromoglycate (DSCG) was chosen as a model drug and different amounts of LL (2-40% w/w) were added to the formulation, with the aim to explore the relationship between powder dispersion, moisture protection and physicochemical properties of the powders. The powder formulations were prepared by spray drying of aqueous solutions containing known concentrations of DSCG and LL. The particle sizes were measured by laser diffraction. The physicochemical properties of fine particles were characterized by X-ray powder diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic vapor sorption (DVS). The surface morphology and chemistry of fine particles were analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). In vitro aerosolization performances were evaluated by a next generation impactor (NGI) after the powders were stored at 60% or 75% relative humidity (RH), and 25 degrees C for 24 h. Spray-dried (SD) DSCG powders were amorphous and absorbed 30-45% (w/w) water at 70-80% RH, resulting in deterioration in the aerosolization performance of the powders. LL did not decrease the water uptake of DSCG powders, but it could significantly reduce the effect of moisture on aerosolization performances. This is due to enrichment of crystalline LL on the surface of the composite particles. The effect was directly related to the percentage of LL coverage on the surface of particles. Formulations having 61-73% (molar percent) of LL on the particle surface (which correspond to 10-20% (w/w) of LL in the bulk powders) could minimize moisture-induced deterioration in the aerosol performance. In conclusion, particle surface coverage of LL can offer short-term protection against moisture on dispersion of hygroscopic powders Refereed/Peer-reviewed

Conventional nebulisation has the disadvantages of low aerosol output rate and potential damage to macromolecules due to high shear (jet nebulisation) or cavitation (ultrasonic nebulisation). HYDRA (HYbriD Resonant Acoustics) technology has been shown to overcome these problems by using a hybrid combination of surface and bulk sound waves to generate the aerosol droplets. We report the first in vivo human lung deposition study on such droplets. Twelve healthy adult subjects inhaled saline aerosols radiolabelled with technetium-99 m complexed with diethylene triamine penta-acetic acid (99mTc-DTPA). The distribution of the aerosolised droplets in the lungs was imaged by single photon emission computed tomography combined with low dose computed tomography (SPECT/CT). The volume median diameter and geometric standard deviation of the droplets were 1.32 ± 0.027 µm and 2.06 ± 0.040, respectively. The mean delivery efficiency from the nebuliser into the body was 51.2%. About 89.1 ± 4.3% and 2.3 ± 1.4% of the inhaled radiolabelled dose deposited in the lungs and oropharynx, respectively. The deposition was symmetrical and diffusive between the two lungs, with a mean penetration index of 0.82. Thus, the prototype HYDRA nebuliser showed excellent in vivo aerosol deposition performance, demonstrating its potential to be further developed for clinical applications.

The present study was conducted to harness spray drying technology as a novel method of producing Ciprofloxacin nanocrystals inside liposomes (CNL) for inhalation delivery. Liposomal ciprofloxacin dispersions were spray dried with sucrose as a lyoprotectant in different mass ratios (0.5:1, 1:1 and 2:1 sucrose to lipids), along with 2% w/w magnesium stearate and 5% w/w isoleucine as aerosolization enhancers. Spray drying conditions were: inlet air temperature 50 °C, outlet air temperature 33-35 °C, atomizer rate 742 L/h and aspirator 35 m3/h. After spray drying, the formation of ciprofloxacin nanocrystals inside the liposomes was confirmed by cryo- transmission electron microscopy. The physiochemical characteristics of the spray dried powder (particle size, morphology, crystallinity, moisture content, drug encapsulation efficiency (EE), in vitro aerosolization performance and drug release) were determined. The EE of the liposomes was found to vary between 44 and 87% w/w as the sucrose content was increased from 25 to 57% w/w. The powders contained partially crystalline particles with a volume median diameter of ~ 1 μm. The powders had low water content (~2 % wt.) and were stable at high relative humidity. Aerosol delivery using the Osmohaler® inhaler at a flow rate of 100 L/min produced an aerosol fine particle fraction (% wt. < 5 μm) of 58 - 64%. The formulation with the highest sucrose content (2:1 w/w sucrose to lipid) demonstrated extended ciprofloxacin release from liposomes (80% released within 7 hours) in comparison to the original liquid formulation (80% released within 2 hours). In conclusion, a stable and inhalable CNL powder with controlled drug release was successfully prepared by spray drying.

We aimed to obtain fundamental information for potential pulmonary delivery of powder aerosols using a clinically-approved nasal high-flow system (AIRVO), with spray-dried mannitol (SD-Man) being a model powder. Compressed air exiting the AIRVO at set 'dispersion' air flow rates dispersed SD-Man loaded in an Osmohaler® into a human nasal airway replica (NAR) coupled downstream to a Next Generation Impactor (NGI) running at specific 'inspiratory' flow rates. Increasing the dispersion flow rate from 30 to 60L/min increased powder deposition in the NAR from 50 to 70% of the emitted dose, while decreased the NGI deposition from 50 to 30% of the emitted dose. The inspiratory flow rate did not affect powder deposition in the NAR and NGI. In contrast, as the inspiratory flow rate was increased from 15 to 40L/min, powder recovery, emitted fraction, and fine particle fraction below 5μm (as aerosol performance indices) were increased from 90, 30 and 5% to 97, 45 and 8% of the loaded dose, respectively. The dispersion flow rate did not change the performance indices. Importantly, heating and humidification of dispersion airflow, loaded doses, and nasal cannula sizes did not greatly affect the aerosol characteristics.

The routine of loading multiple capsules for delivery of high-dose antibiotics is time consuming, which may reduce patient adherence to inhaled treatment. To overcome this limitation, an investigation was carried out using four modified versions of the Aerolizer® that accommodate a size 0 capsule for delivery of high payload formulations. In some prototypes, four piercing pins of 0.6 mm each were replaced with a single centrally located 1.2-mm pin and one-third reduced air inlet of the original design. The performance of these inhalers was evaluated using spray-dried antibiotic powders with distinct morphologies: spherical particles with a highly corrugated surface (colistin and tobramycin) and needle-like particles (rifapentine). The inhalers were tested at capsule loadings of 50 mg (colistin), 30 mg (rifapentine) and 100 mg (tobramycin) using a multistage liquid impinger (MSLI) operating at 60 L/min. The device with a single pin and reduced air inlet showed a superior performance than the other prototypes in dispersing colistin and rifapentine powders, with a fine particle fraction (FPF wt%

The design of a dry powder inhaler device has significant influence on aerosol performance; however, such influence may be different between the drug-only and carrier-based formulations. The present study aims to examine the potential difference on the dispersion between these distinct types of formulations, using Aerolizer(®) as a model inhaler with the original or modified (cross-grid) designs. A coupled CFD-discrete element method analysis was employed to determine the flow characteristics and particle impaction. Micronized salbutamol sulphate as a drug-only formulation and three lactose carrier-based formulations with various drug-to-carrier weight ratios 1:5, 1:10 and 1:100 were used. The in vitro aerosolization performance was assessed by a next-generation impactor operating at 100 L/min. Using the original device, FPFloaded was reduced from 47.5 ± 3.8% for the drug-only formulation to 31.8 ± 0.7%, 32.1 ± 0.7% and 12.9 ± 1.0% for the 1:5, 1:10 and 1:100 formulations, respectively. With the cross-grid design, powder-mouthpiece impaction was increased, which caused not only powder deagglomeration but also significant drug retention (doubling or more) in the mouthpiece, and the net result is a significant decrease in FPFloaded to 36.8 ± 1.2%, 20.9 ± 2.6% and 21.9 ± 1.5% for the drug-only, 1:5 and 1:10 formulations, respectively. In contrast, the FPFloaded of the 1:100 formulation remained the same at 12.1 ± 1.3%, indicating the increased mouthpiece drug retention was compensated by increased drug detachment from carriers caused by increased powder-mouthpiece impaction. In conclusion, this study has elucidated different effects and the mechanism on the aerosolization of varied dry powder inhaler formulations due to the grid design.

We hypothesize that the USP induction port may de-agglomerate carrier-free powder emitting from dry powder inhalers (DPIs).Aerosols emitting from a range of DPIs (Spinhaler®, Turbuhaler® and Osmohaler™) and induction ports (USP throat, straight tube, Alberta idealized mouth-throat geometry (AG)) were sized by laser diffraction. Total drug recovery was obtained by HPLC and fine particle fraction computed. Air flow patterns were simulated using Computational Fluid Dynamics (CFD).The straight tube did not de-agglomerate emitted powder. However, the USP throat and AG further de-agglomerated powders from the Spinhaler, but not the Turbuhaler and Osmohaler. While budesonide powder deposited similarly in all induction ports, deposition was significantly higher in the AG for both DSCG and mannitol. CFD revealed agglomerates impacting on the USP throat with higher localized velocity compared with the straight tube. CFD further showed a more complex flow pattern with high-velocity air jets in the AG, which explains the higher FPF for DSCG and the lower FPF for mannitol using the AG.The USP throat further de-agglomerated the emitted powder from the DPI when it did not sufficiently disperse the powder. Other tools such as laser diffraction may be used for cross-examining to avoid artifacts in the results.

The aim of this study was to develop a method for converting an amorphous drug to a crystalline form to enhance its stability and inhalation performance. Spray-dried amorphous salbutamol sulphate powder was conditioned with supercritical carbon dioxide (scCO 2 ) modified with menthol. The effect of menthol concentration, pressure, temperature and time on the characteristics of the resulting salbutamol sulphate powder was investigated. Pure scCO 2 had no effect on the physical properties of amorphous salbutamol sulphate; however, scCO 2 modified with menthol at 150 bar and 50 °C was efficient in converting amorphous drug to crystalline form after 12 h of conditioning. The average particle size of powders decreased slightly after the conditioning process because of reducing agglomeration between particles by increasing surface roughness. Emitted dose measured by the fine particle fraction (FPF emitted ) of amorphous salbutamol sulphate was enhanced from 32% to 43% after conditioning with scCO 2 + menthol and its water uptake was significantly decreased. This study demonstrates the potential of scCO 2 + menthol for converting amorphous forms of powders to crystalline, while preserving the particle size.

Atomic force microscopy (AFM) was used to evaluate the particle adhesion and surface morphology of engineered particles for dry powder inhaler (DPI) respiratory therapy to gain a greater understanding of interparticle forces and the aerosolisation process. A series of spherical model drug particles of bovine serum albumin (BSA) was prepared with different degrees of surface corrugation. The particles were evaluated in terms of particle size (laser diffraction) and microscopic morphology (scanning electron microscopy). Conventional tapping mode AFM was used to evaluate the nanoscopic morphology and derive specific roughness parameters, while AFM colloid probe microscopy was used to directly measure the interaction of functionalised probes. The physical characterisation and AFM measurements were evaluated in terms of in vitro aerosolisation performance, using a conventional Rotahaler((R)) DPI and multistage liquid impinger. A direct relationship between the root mean square roughness, particle adhesion and in vitro aerosol performance (measured as fine particle fraction, FPF) was observed suggesting that as the degree of corrugation increased, particle adhesion was reduced which, resulted in a concomitant increase in FPF. This study demonstrates that AFM may be used to predict the aerosolisation performance micron sized particles for inhalation based on their morphological properties.

The current study aimed to examine the pharmaceutical applications of the focused-ion-beam (FIB) in the inhalation aerosol field, particularly to particle porosity determination (i.e. percentage of particles having a porous interior). The interior of various spray dried particles (bovine serum albumin (BSA) with different degrees of surface corrugation, mannitol, disodium cromoglycate and sodium chloride) was investigated via FIB milling at customized conditions, followed by viewing under a high resolution field-emission scanning electron microscope. Two sets of ten particles for each sample were examined. For the spray-dried BSA particles, a decrease in particle porosity (from 50 to 0%) was observed with increasing particle surface corrugation. Spray-dried mannitol, disodium cromoglycate and sodium chloride particles were determined to be 90–100%, 0–10% and 0% porous, respectively. The porosity in the BSA and mannitol particles thus should be considered for the aerodynamic behaviour of these particles. The FIB technology represents a novel approach useful for probing the interior of particles linking to the aerosol properties of the powder. Suitable milling protocols have been developed which can be adapted to study other similar particles.

The US pharmacopeia (USP) and Alberta throats were recently reported to cause further de-agglomeration of carrier-free powders emitted from some dry powder inhalers (DPIs). This study assessed if they have similar influences on commercially available carrier-based DPIs. A straight tube, a USP throat, and an Alberta throat (non-coated and coated) were used for cascade impaction testing. Aerosol fine particle fraction (FPF ≤ 5 μm) was computed to evaluate throat-induced de-agglomeration. Computational fluid dynamics are employed to simulate airflow patterns and particle trajectories inside the USP and Alberta throats. For all tested products, no significant differences in the in vitro aerosol performance were observed between the USP throat and the straight tube. Using fine lactose carriers (10 μm), Symbicort(®) and Oxis(™) showed minimal impaction inside the Alberta throat and resulted in similar FPF among all induction ports. For products using coarse lactose carriers (10 μm), impaction frequency and energy inside the Alberta throat were significant. Further de-agglomeration was noted inside the non-coated Alberta throat for Seretide(®) and Spiriva(®), but agglomerates emitted from Relenza(®), Ventolin(®), and Foradil(®) did not further break up into smaller fractions. The coated Alberta throat considerably reduced the FPF values of these products due to the high throat retention, but they generally agreed better with the in vivo data. In conclusion, depending on the powder formulation (including carrier particle size), the inhaler, and the induction port, further de-agglomeration could happen ex-inhaler and create differences in the in vitro measurements.

Currently bronchial provocation testing (BPT) using mannitol powder cannot be performed in children under 6 years. A primary reason is it is challenging for children at this age to generate a consistent inspiratory effort to inhale mannitol efficiently from a dry powder inhaler. A prototype system, which does not require any inhalation training from the pediatric subject, is reported here. It uses an external source of compressed air to disperse mannitol powder into a commercial holding chamber. Then the subject uses tidal breathing to inhale the aerosol.The setup consists of a commercially available powder disperser and Volumatic™ holding chamber. Taguchi experimental design was used to identify the effect of dispersion parameters (flow rate of compressed air, time compressed air is applied, mass of powder, and the time between dispersion and inhalation) on the fine particle dose (FPD). The prototype was tested in vitro using a USP throat connected to a next generation impactor. The aerosols from the holding chamber were drawn at 10 L/min. A scaling factor for estimating the provoking dose to induce a 15% reduction in forced expiratory volume in 1 second (FEV1) (PD15) was calculated using anatomical dimensions of the human respiratory tract at various ages combined with known dosing values from the adult BPT.Consistent and doubling FPDs were successfully generated based on the Taguchi experimental design. The FPD was reliable over a range of 0.8 (±0.09) mg to 14 (±0.94) mg. The calculated PD15 for children aged 1-6 years ranged from 7.1-30 mg. The FPDs generated from the proposed set up are lower than the calculated PD15 and therefore are not expected to cause sudden bronchoconstriction.A prototype aerosol delivery system has been developed that is consistently able to deliver doubling doses suitable for bronchial provocation testing in young children.

Respiratory infections represent a major global health problem. They are often treated by parenteral administrations of antimicrobials. Unfortunately, systemic therapies of high-dose antimicrobials can lead to severe adverse effects and this calls for a need to develop inhaled formulations that enable targeted drug delivery to the airways with minimal systemic drug exposure. Recent technological advances facilitate the development of inhaled anti-microbial therapies. The newer mesh nebulisers have achieved minimal drug residue, higher aerosolisation efficiencies and rapid administration compared to traditional jet nebulisers. Novel particle engineering and intelligent device design also make dry powder inhalers appealing for the delivery of high-dose antibiotics. In view of the fact that no new antibiotic entities against multi-drug resistant bacteria have come close to commercialisation, advanced formulation strategies are in high demand for combating respiratory 'super bugs'.

The objective of this study is to investigate the effect of device design of the Aerolizer(®) on the aerosolization of a carrier-based dry powder inhaler formulation (Foradile(®)). The Aerolizer was modified by reducing the air inlet size and mouthpiece length to 1/3 of the original dimensions, or by increasing the grid voidage. Aerosolization of the powder formulation was assessed on a multi-stage liquid impinger at air flow rates of 30, 60, and 100 L/min. Coupled CFD-DEM simulations were performed to investigate the air flow pattern and particle impaction. There was no significant difference in the aerosolization behavior between the original and 1/3 mouthpiece length devices. Significant increases in FPF total and FPF emitted were demonstrated when the inlet size was reduced, and the results were explained by the increases in air velocity and turbulence from the CFD analysis. No significant differences were shown in FPF total and FPF emitted when the grid voidage was increased, but more drugs were found to deposit in induction port and to a lesser extent, the mouthpiece. This was supported by the CFD-DEM analysis which showed the particle-device collisions mainly occurred in the inhaler chamber, and the cross-grid design increased the particle-device collisions on both mouthpiece and induction port. The air inlet size and grid structure of the Aerolizer(®) were found to impact significantly on the aerosolization of the carrier-based powder.

Mannitol particles, produced by spray drying (SD), have been used commercially (Aridol) in bronchial provocation test. In this study, we propose an alternative method to produce inhalable mannitol powders. The elongated mannitol particles (number median length 4.0microm, and axial ratio of 3.5) were prepared using a confined liquid impinging jets (CLIJs) followed by jet milling (JM). Spray dried and jet milled raw mannitol particles were compared in an attempt to assess the performance of the particles produced by the new method. Aerosol performance of the three different powders (CLIJ, SD, and JM) was relatively poor (fine particle fraction or FPF(loaded) below 15%) when dispersed by the Rotahaler. Dispersion through the Aeroliser led to better aerosol performance of the CLIJ mannitol (FPF(loaded) 20.3%), which is worse than the JM (FPF(loaded) 30.3%) and SD mannitol particles (FPF(loaded) 45.7%) at 60 L/min, but comparable (FPF(loaded) 40.0%) with those of the JM (FPF(loaded) 40.7%) and SD (FPF(loaded) 45.5%) powders at 100L/min. Hence, the optimum use of these elongated mannitol particles can be achieved at increased air flow with a more efficient inhaler. In addition to crystallinity, morphology, and particle size distribution, the surface energies of these powders were measured to explain the differences in aerosol performance. A major advantage of using the CLIJ method is that it can be scaled up with a good yield as the precipitate can be largely collected and recovered on a filter, compared with spray drying which has a low collection efficiency for fine particles below 2microm.