Search

Additive manufacturing (AM) is a potential technology to be applied for replacing wood joints in the furniture industry. Overall, 3D-printed connectors have a lot of advantages in chair construction: the possibility of improving the design by using colored materials and new concepts with no limits of shape and size, avoiding the use of synthetic materials such as adhesives and finishing materials. The present research shows the results of the research conducted on 3D-printed connectors for a chair leg-stretchers joint. Larch (Larix decidua Mill.) wood was used for chair components and selective laser sintering (SLS) technology was employed for the 3D-printing connector designed to assemble the chair elements. Diagonal tensile and compression tests were performed on the L-type joints with 3D-printed connectors and the bending moments were determined and compared to the results obtained after testing the leg-stretchers mortise–tenon joints made of larch wood, taken as a reference. Micrograph investigation was finally performed on the broken areas of the 3D-printed connectors as a result of mechanical testing failures. The results show that the SLS printing technology applied to build the connector does not ensure enough strength to the assembly, and changes in printing parameters are needed for further research, in terms of laser power and scan speed. [ABSTRACT FROM AUTHOR]

In this paper, a blade with unconventional structure, corrugations and BERP tip, used in UAV helicopters, was designed, analyzed and additively manufactured. Aerodynamically, the unconventional blade shows better performance compared to the conventional blade at positive angles of attack. Acoustically, the unconventional blade showed a reduced noise level compared to the conventional blade. Acoustic testing of additively manufactured samples with five honeycomb core configurations showed higher performance for the 1.5 mm honeycomb cell samples 3D printed from T-PLA. [ABSTRACT FROM AUTHOR]

The paper presents the influence of the loading modelling on the simulation process results of the bending behaviour for 3D printed structures. The study is done on structures having different geometries of the cross section, and the type of structure is bar or tube. The materials used for 3D printing are poly(lactic) acid and poly(lactic acid) mixed with glass fibres. The simulation was carried out both based on a simple modelling (schematization) of the bending loading and a complex one. The complex modelling reproduces the bending of 3D printed structures more accurately but is also more time-consuming for the computer-aided design stage. Analysis of the study results shows that in terms of the Von Mises stresses determined by simulation, they are in line with those of the tests but with a slight advantage for the complex modelling compared to the simple one. In terms of deformations, the simulation introduces errors compared to the test results, but the source of the errors is the high elasticity of some 3D printed structures. The study also shows that the high elasticity is due to both the shape of the structure cross section and its arrangement during the bending test. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) is used in many fields and is a method used to replace wood components or wood-jointed furniture components in the furniture industry. Replacing wood joints by 3D printed connectors would be an advantage, considering the fact that during the process of assembling furniture, the execution technology of the joints is difficult, time-consuming, and labor-intensive. Advanced technology of AM applied in furniture manufacturing helps the designers to create new concepts of product design, with no limits of shape, number of joints, color, or size. The diversity of 3D printers and AM technologies provides the selection of materials in relation with the applicability of the 3D printed object. In this respect, the objective of the present research is to design a 3D printed connector to be used for jointing three chair components, namely the leg and two stretchers made from larch (Larix decidua Mill.) wood, and to use reinforced polylactic acid (PLA) fiberglass (20 wt. %) filament for 3D printing this connector using AM with fused filament fabrication (FFF) technology. The design of the connector, the possibility of using this type of material, and the deposition method of filament were investigated in this research. For this purpose, several evaluation methods were applied: microscopic investigation with 50×, 100×, and 200× magnifications, both of the filament and of the 3D printed connector; mechanical testing of corner joint formed with the help of connector between chair leg and the two stretchers; and a microscopic investigation of the connectors' defects that occurred after applying the compression and tensile loads on the diagonal direction of the L-type joint. The microscopic investigation of the composite filament revealed the agglomerations of glass fibers into the core matrix and areas where the distribution of the reinforcements was poor. The heterogeneous structure of the filament and the defects highlighted in the 3D printed connectors by the microscopic investigation contributed to the mechanical behavior of L-type connecting joints. The bending moments resulting from compression and tensile tests of the 3D printed connectors were compared to the results recorded after testing, under the same conditions, the normal mortise–tenon joint used to assemble the abovementioned chair components. The larch wood strength influenced the mechanical results and the conclusions of the microscopic investigations, as well as the analysis of the broken connectors after testing recommended the change of connector design and filament deposition direction. [ABSTRACT FROM AUTHOR]

With the fourth industrial revolution, Additive Manufacturing started to offer new possibilities of manufacturing, Fused Deposition Modeling being one of the most used processes for fabrication. In this paper, the studied specimens are manufactured based on the Fused Deposition Modeling (FDM) method, with a filament of short carbon fiber and polyethylene terephthalate (PET) matrix, with a variation of the layer thickness. For the resulted specimens the tensile properties are determined according to ASTM D638. The most advantageous results are obtained for the layer thickness of 0.15 mm, with the tensile strength of 58 MPa. Based on the stress-strain curves which are presented in this paper, it also can be assumed that the material is brittle. The results of the mechanical properties are very similar for each group of specimens and it can be assumed that the mechanical properties are homogenous due to the material quality and the machine performances. For all the specimens the rupture location is almost in the same area. Due to the difficulty of carbon fiber filament printing, the manufacturing defectives which appear during the manufacturing process are detected, the most common manufacturing defectives being the material gaps from each specimen, which are identified with microstructural analysis. As failure modes, the most common failure criteria are the delamination and the matrix cracks. [ABSTRACT FROM AUTHOR]

The main objective was to reduce the consumption of material when obtaining 3D printed parts (different empty shapes inside) and the secondary one was to maintain the mechanical properties closer to the full printed version. In order to achieve these objectives, two internal configurations were designed - a configuration with hexagonal gaps (material reduction was 30%) and a configuration with sinuous gaps (material reduction was 15%). The specimens thus obtained were tested for traction, threepoint bending and shock (resilience). Hexagonal hollow configuration has a resistance values close to those of solid specimens but with the advantage of consuming with 30% less material. [ABSTRACT FROM AUTHOR]

Being a relatively new process, additive manufacturing needs many studies to be able to produce parts with the required properties. The aim of the paper is to establish whether, based on the physical and mechanical properties determined by tensile testing and by applying finite element analysis (FEA), viable results can be obtained regarding the behavior of the 3D printed structures at the different, static loading. The application of FEA for the tensile testing of 3D specimens led to the results close to those obtained by the tests. The values of the results obtained by simulation are higher by up to 7.2% compared with those recorded by tests. The simulation was applied both for the printed specimens from a single material and from two materials (multi‐material). Regardless of the materials used in printing and the simulation method, the results of applying FEA are close to those recorded by testing. [ABSTRACT FROM AUTHOR]

The additive manufacturing process is one of the technical domains that has had a sustained development in recent decades. The designers' attention to equipment and materials for 3D printing has been focused on this type of process. The paper presents a comparison between the results of the bending tests and those of the simulation of the same type of stress applied on 3D-printed PLA and PLA–glass structures. The comparison of the results shows that they are close, and the simulation process can be applied with confidence for the streamline of filament consumption, with direct consequences on the volume and weight of additive manufactured structures. The paper determines whether the theories and concepts valid in the strength of materials can be applied to the additive manufacturing pieces. Thus, the study shows that the geometry of the cross-section, by its shape (circular or elliptical) and type (solid or ring shaped), influences the strength properties of 3D-printed structures. The use of simulation will allow a significant shortening of the design time of the new structures. Moreover, the simulation process was applied with good results on 3D-printed structures in which two types of filaments were used for a single piece (structure). [ABSTRACT FROM AUTHOR]

The utilization of polymer-based materials is quickly expanding. The enterprises of today are progressively seeking techniques to supplant metal parts with polymer-based materials as a result of their light weight, simple support and modest costs. The ceaselessly developing requirement for composite materials with new or enhanced properties brings about the preparation of different polymer mixes with various arrangements, morphologies and properties. Fused filament fabrication processes such as 3D-printing are nowadays shaping the actual pathway to a full pallet of materials, from art–craft to biomaterials. In this study, the structural and mechanical behavior of three types of commercially available filaments comprised of synthetic poly(acrylonitrile-co-butadiene-co-styrene) (ABS), poly(lactic acid) (PLA) and poly(lactic acid)/polyhydroxyalkanoate reinforced with bamboo wood flour composite (PLA/PHA BambooFill) were assessed through mechanical testing and optical microscopy, aiming to understand how the modifications that occur in the printed models with internal architecture are influencing the mechanical properties of the 3D-printed material. It has been determined that the material printed from PLA presents the highest compression strength, three-point bending and shock resistance, while the ABS shows the best tensile strength performance. A probability plot was used to verify the normality hypothesis of data for the tensile strength, in conjunction with the Anderson–Darling statistic test. The results of the statistic indicated that the data were normally distributed and that there is a marked influence of the internal architecture of the 3D-printed models on the mechanical properties of the printed material. [ABSTRACT FROM AUTHOR]